FAMILY & CONSUMER SCIENCES RESEARCH JOURNAL, Issue 3 2002
Patricia E. Horridge
Using the physical dimension triad of Branson and Sweeney's Model for Clothing Comfort as a conceptual framework, the purpose of the study was to examine the effects of cotton/wool fabrics on comfort and wear of trooper uniforms. Participants were 10 troopers recruited for wear- testing uniforms developed in accordance to Texas Department of Public Safety specifications. Trooper shirt and pants fabrics were developed in two fiber contents (80/20 and 70/30 cotton/wool) and tested before and after dry-cleaning. Twenty constructed uniforms and 10 issued uniforms were worn through four wear-refurbishing-dry-cleaning cycles. Surveys and scales were used to gather data during and after wear testing; data were analyzed by t-test and ANOVAs. Branson and Sweeney's comfort model was supported, in part, with person attributes (body weight, hours uniform worn) affecting uniform comfort. Implications are given for fabric producers and garment manufacturers. [source]

The Golden Freeway: a preliminary evaluation of a pilot study advancing information technology as a social intervention for boys with Duchenne muscular dystrophy and their families

HEALTH & SOCIAL CARE IN THE COMMUNITY, Issue 1 2004
Jennifer Soutter BSc PhD
Abstract Established information technology was used in an attempt to reduce social isolation by providing each family who had a child with Duchenne muscular dystrophy with a personal computer, and e-mail and Internet connectivity. Seventy-four of the 88 families in the north of England (i.e. Cumbria, Durham, Northumberland, Teesside, and Tyne and Wear) with a boy with Duchenne muscular dystrophy who was diagnosed before January 2000 had the equipment installed. Evaluations of equipment usage and parental perceptions of the project were carried out at 3 and 12 months post-installation. Results from quantitative and qualitative interviews with parents indicated that benefits accrued to the families and to the boys themselves: family relationships can be extended, and the boys can acquire a degree of independence which, according to parents' views, can boost self-confidence and self-esteem. As hoped, social isolation was felt to have been reduced, and an occupation, interest and enjoyment provided. The greatest use of the computer was for schoolwork with siblings sharing in this. Cost proved to be a problem for a number of families. For the project team, there were unexpected aspects: creating an e-community was more difficult than anticipated, more training was required and not all families would ever use the equipment to its fullest. However, families did emphasise the value of the project as a way of opening the world for their sons. [source]

Numerical derivation of contact mechanics interface laws using a finite element approach for large 3D deformation

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING, Issue 2 2004
Alex Alves Bandeira
Abstract In this work a homogenization method is presented to obtain by numerical simulation interface laws for normal contact pressure based on statistical surface models. For this purpose and assuming elastic behaviour of the asperities, the interface law of Kragelsky et al. (Friction and Wear,Calculation Methods, Pergamon, 1982) is chosen for comparison. The non-penetration condition and interface models for contact that take into account the surface micro-structure are investigated in detail. A theoretical basis for the three-dimensional contact problem with finite deformations is shortly presented. The augmented Lagrangian method is then used to solve the contact problem with friction. The algorithms for frictional contact are derived based on a slip rule using backward Euler integration like in plasticity. Special attention was dedicated to the consistent derivation of the contact equations between finite element surfaces. A matrix formulation for a node-to-surface contact element is derived consisting of a master surface segment with four nodes and a contacting slave node. It was also necessary to consider the special cases of node-to-edge contact and node-to-node contact in order to achieve the desired asymptotic quadratic convergence in the Newton method. A numerical example is selected to show the ability of the contact formulation and the algorithm to represent interface law for rough surfaces. Copyright © 2003 John Wiley & Sons, Ltd. [source]

Wear in molded tibial inserts: Knee simulator study of H1900 and GUR1050 polyethylenes

JOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 2 2008
Riichiro Tsukamoto
Abstract Hi-fax 1900Ô tibial inserts were used in the IB-1 total knee replacement (TKR) beginning 1978, soon followed by the AGC design. Such direct compression molded (DCM) inserts was relatively immune to oxidation. Unfortunately the Hi-fax 1900Ô resin (H1900) was taken off the market in year 2004. As an alternate, GUR1050 was introduced in the VanguardÔ TKR. However there appeared to be little or no wear comparisons of molded inserts. Therefore the study aim was to compare wear performance of GUR1050 to the historical H1900. The hypothesis was that Hi-fax and GUR1050 would show comparable wear performance. The VanguardÔ was a posterior-cruciate sacrificing design (Biomet Inc.). All tibial inserts were sterilized by gamma-radiation (3.2 Mrad) under argon. A 6-channel, displacement,controlled knee simulator was used with serum lubricant (protein concentration 20 mg/mL). Wear assessments were by gravimetric methods and linear regression techniques. The gross weight-loss trends over 2.5 Mc duration demonstrated excellent linear behavior with good agreement between TKR sets (<±10%). Fluid sorption artifacts in control represented less than 5% of gross wear magnitudes. Thus suitable corrections could be made in determining net wear. The H1900 and GUR1050inserts demonstrated net wear-rates of 3.6 and 3.4 mm3/Mc, respectively. This difference was not found to be statistically significant. This wear study demonstrated that GUR1050 inserts were indistinguishable from the Hi-fax 1900 in terms of laboratory wear performance, proving our hypothesis. Given the excellent clinical history of DCM Hi-fax 1900, the GUR1050 should be an ideal candidate for TKR. © 2007 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008 [source]

Diagnosis and Management of Maxillary Incisors Affected by Incisal Wear: An Interdisciplinary Case Report

JOURNAL OF ESTHETIC AND RESTORATIVE DENTISTRY, Issue 6 2002
JUSSARA KARINA BERNARDON
ABSTRACT In the attempt to restore anterior teeth affected by erosion and bruxism, many clinicians have been frustrated with the constant restorative failures. Frequently, these failures are attributed to the restorative materials employed, especially in cases in which composite resins are used. However, some flaws of the restorations are related to the oversight of occlusal principles. The purpose of this article is to discuss the etiology, signs, and symptoms of incisal wear, with special attention to that caused by bruxism and chemical erosion. Relatively simple management techniques (e.g., occlusal adjustment, adhesive restorations) are proposed, and the diagnosis and management of a representative clinical case is presented. [source]

Surface wear of incoloy and darvic bands on Atlantic Puffin adults and chicks

JOURNAL OF FIELD ORNITHOLOGY, Issue 2 2006
André R. Breton
ABSTRACT Bands are a common marking method in bird studies and capture-mark-reencounter (CMR) models are often used to analyze banding data. Common to this family of models are two assumptions: marks do not fall off or become unreadable and individuals within groups remain equally detectable. When data fail to meet these assumptions, results of CMR analyses may be biased. In studies of long-lived seabirds exposed to coarse nesting substrates, band wear is especially problematic. We compared surface wear from abrasion against rocks on incoloy and darvic bands applied to a long-lived seabird, the Atlantic Puffin (Fratercula arctica). In 2003 and 2004, surface wear on bands applied to chicks and adults was scored at five colonies in the Gulf of Maine. We used logistic regression to analyze two subsets of these data by fitting the probability of being worn (one or more characters difficult to read or obliterated) to band age, bird age, and band type. In both analyses, an evidence ratio provided exclusive support for the model that included all factors. Immature puffins largely avoid colonies and remain at sea until their second or third summer after hatching. Consequently, probabilities of being worn were delayed on both band types by 4 yr on bands applied to chicks compared to adults. Based on our estimates, 25% and 87% of darvic bands applied to chicks and adults, respectively, were worn after 5 yr. Wear was reduced by 71% and 87% annually on incoloy compared to darvic bands applied to adults and chicks, respectively. To uphold assumptions of CMR models, we recommend incoloy bands over darvic in studies spanning more than about 5 yr of long-lived seabirds exposed to coarse substrates. SINOPSIS Las anillas colocadas en las patas son un método común de marcar aves y se han establecido modelos (recuento de aves marcadas , siglas en inglés CMR) para analizar los datos obtenidos de esta forma. Hay dos postulados que deben aceptarse en estos modelos: que las anillas no se pierden o que se puedan leer y que los individuos marcados y no-marcados tienen la misma probabilidad de ser contados. Cuando los datos no cumplen con las dos condiciones previamente mencionadas el análisis de CMR puede contener sesgo. En estudios de ave marinas que viven por mucho tiempo, el desgaste de las anillas crea problemas. Comparamos el desgaste y daño de anillas de metal (niquel-cromio y acero) y anillas de plástico (policloruro de vinilo) colocadas en individuos de Fratercula arctica. Durante el 2003 y 2004, estudiamos el desgaste y daño de anillas colocadas a pichones y adultos del ave en cinco colonias de estas en el Golfo de Maine. Utilizamos una regresión logística para analizar dos conjuntos de datos sobre la probabilidad de desgaste (uno o más caracteres en la anilla difíciles de leer) a la edad de la anilla (tiempo en la pata del ave), edad del ave y tipo de anilla. Las aves inmaduras, evitan los grupos en las colonias y permanecen en el mar hasta el segundo o tercer verano. Como resultado, la probabilidad de que ambos tipos de anillas hubieran estado desgastadas o dañadas en los juveniles se dilato por unos cuatro años, al ser este grupo comparado con los adultos. El 25% y el 87% de las anillas plásticas colocadas en pichones y adultos, respectivamente, estaban desgastadas a los cinco años. El desgaste en las anillas de metal se redujo en un 71% y 87% anual al compararse con las plásticas colocadas en adultos y pichones, respectivamente. Para cumplir con los postulados de los modelos CMR, recomendamos el uso de anillas de metal en aquellos estudios pautados para más de cinco años particularmente en aves marinas que utilizan o se exponen a sustratos duros. [source]

Distinguishing Between Damage to Clothing as a Result of Normal Wear and Tear or as a Result of Deliberate Damage: A Sexual Assault Case Study

JOURNAL OF FORENSIC SCIENCES, Issue 2 2009
Dyan J. Daly Ph.D.
Abstract:, This paper focuses on bra damage, specifically damage observed in hook and eye fasteners that are generally located at the backstraps of bras. We describe bra design including the method by which hook and eye fasteners are generally constructed. We assess bra damage in two situations where the damage observed was unexpected given the case scenarios. These were: (i) the complainant of an alleged rape attributed damage to her bra hooks to force during a struggle and (ii) the complainant had earlier manipulated her bra hooks in an incident not related to her complaint. Steriomicroscopy and reconstruction experimentation were necessarily used to assess the bra damage. A systematic approach to damage analysis was employed by the forensic practitioners to correctly identify damage as being a result of mechanical manipulation and therefore as falsified. This paper suggests that more examples of falsified damage should be documented. [source]

Age Estimation of Korean Adults by Occlusal Tooth Wear

JOURNAL OF FORENSIC SCIENCES, Issue 3 2007
Jong-Il Yun M.S.D.
ABSTRACT: The aim of the present study was to evaluate the validity of the modified Kim's scoring system as a practical method of recording occlusal tooth wear and estimating age. For this purpose, 1092 pairs of maxillary and mandibular full-arch casts were randomly selected, scored, and analyzed. The results showed that the modified Kim's scoring system had excellent reliability, and that occlusal tooth wear had a positive correlation with age. Tooth wear scores of all teeth except the two lower central incisors were higher in males than in females. Calculating tables for age estimation were designed by multiple linear regression analysis. Estimated ages were within ±5 years of actual ages in 63.5% of male subjects, and 64.0% of female subjects. The accuracy of age estimation was increased when the subjects were divided into two age groups and data were re-analyzed. Collectively, it was shown that the modified Kim's scoring system is a reliable and accurate method for age estimation, and that the data from these 1092 individuals can be used as a standard for age estimation of Korean adults. [source]

Wear of human enamel and nano-filled composite resin denture teeth under different loading forces

JOURNAL OF ORAL REHABILITATION, Issue 1 2009
M. GHAZAL
Summary, To evaluate and correlate the two-body wear of human enamel and nano-filled composite resin teeth with the loading forces used in a dual-axis chewing simulator. Three groups of human enamel and three of nano-filled composite resin teeth were tested in a chewing simulator. Zirconia ceramic balls were used as antagonists. The teeth were tested with three different loading forces (20, 49 and 78 N). Wear was analysed by measuring the volume and vertical substance loss using a laser scanner after 300000 chewing cycles. Data were statistically analysed using two-way anova followed by the Scheffé test (P , 0·05). Spearman correlation test was used to determine whether there was a relationship between the loading force and the degree to which the human enamel and composite resin had worn. An increase in the loading force significantly increased the wear of composite resin and of human enamel. The effect of the loading force on the wear was statistically significant at the 0·001 level. Human enamel showed a lower volume and vertical substance loss than composite resin under loading forces of 20 and 49 N and lower vertical loss under loading force of 78 N. The correlation between the volume loss and loading force was statistically significant (r = 0·616, P < 0·001). Nano-filled composite resin and human enamel exhibited different amount of wear under different loading forces. In general, human enamel showed less vertical substance loss than nano-filled composite resin. [source]

Wear, delamination, and fatigue resistance of melt-annealed highly crosslinked UHMWPE cruciate-retaining knee inserts under activities of daily living

JOURNAL OF ORTHOPAEDIC RESEARCH, Issue 9 2010
Oludele O. Popoola
Abstract The wear, delamination, and fatigue resistance of artificially aged gamma irradiation-sterilized conventional polyethylene (CPE) and gas-plasma-sterilized melt-annealed highly crosslinked polyethylene tibial inserts (HXPE) were compared. Six CPE and 12 HXPE (six irradiated at 58,kGy and six at 72,kGy) left knee inserts were wear tested for 5.5 million cycles (Mc) under loads and motions that mimic activities of daily living, such as walking, chair rise, stair ascent, and deep squatting. Another six HXPE (72,kGy) and six CPE inserts were also tested under conditions that could produce severe delamination for 8 Mc. Ten other knees (five 72,kGy HXPE and five CPE) were subjected to posterior edge loading fatigue testing for 5 Mc. The HXPE inserts had an average wear rate reduction of about 80% relative to their CPE counterparts during all activities. All of the CPE inserts delaminated and fractured during high cycle deep squat (152° flexion) motions, while all the HXPE remained intact. None of the HXPE inserts delaminated after 8 Mc, while all of the CPE inserts developed delamination damage within 1.5,5.8 Mc of delamination testing. All CPE inserts developed subsurface cracks and delamination within 2.8 Mc during posterior edge loading fatigue studies, while none of the HXPE inserts showed cracking or delamination after 5 Mc. These results show that aged HXPE has higher wear and fatigue resistance than aged CPE, and offers potential long-term advantages for young active patients with sustained activities of daily living. © 2010 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 28:1120,1126, 2010 [source]

Confocal Examination of Subsurface Cracking in Ceramic Materials

JOURNAL OF PROSTHODONTICS, Issue 7 2009
MMedSc, Maged K. Etman DDS
Abstract Purpose: The original ceramic surface finish and its microstructure may have an effect on crack propagation. The purpose of this study was to investigate the relation between crack propagation and ceramic microstructure following cyclic fatigue loading, and to qualitatively evaluate and quantitatively measure the surface and subsurface crack depths of three types of ceramic restorations with different microstructures using a Confocal Laser Scanning Microscope (CLSM) and Scanning Electron Microscope (SEM). Materials and Methods: Twenty (8 × 4 × 2 mm3) blocks of AllCeram (AC), experimental ceramic (EC, IPS e.max Press), and Sensation SL (SSL) were prepared, ten glazed and ten polished of each material. Sixty antagonist enamel specimens were made from the labial surfaces of permanent incisors. The ceramic abraders were attached to a wear machine, so that each enamel specimen presented at 45 degrees to the vertical movement of the abraders, and immersed in artificial saliva. Wear was induced for 80K cycles at 60 cycles/min with a load of 40 N and 2-mm horizontal deflection. The specimens were examined for cracks at baseline, 5K, 10K, 20K, 40K, and 80K cycles. Results: Twenty- to 30-,m deep subsurface cracking appeared in SSL, with 8 to 10 ,m in AC, and 7 ,m close to the margin of the wear facets in glazed EC after 5K cycles. The EC showed no cracks with increasing wear cycles. Seventy-,m deep subsurface cracks were detected in SSL and 45 ,m in AC after 80K cycles. Statistically, there was significant difference among the three materials (p < 0.05). Bonferroni multiple comparison of means test confirmed the ANOVA test and showed that there was no statistical difference (p > 0.05) in crack depth within the same ceramic material with different surface finishes. Conclusions: The ceramic materials with different microstructures showed different patterns of subsurface cracking. [source]

Soot,additive interactions in engine oils

LUBRICATION SCIENCE, Issue 1 2010
Dairene Uy
Abstract Soot is known to cause engine wear. In this work, we focus on how engine oil formulation affects soot-related wear, and how the lubricant-derived anti-wear film changes when soot is present. Friction and wear experiments of fully and partially formulated diesel engine oils (containing basestock, dispersants and viscosity modifiers) are conducted with a ball-on-disk rig in the presence of carbon black (CB) as a soot surrogate. The friction coefficient was largely unaffected by CB dispersed in the oils, but electrically insulating film formation, an indication of the formation of anti-wear films, was decreased. Wear on the disk was found to either remain the same or decrease when CB was present, depending on the oil formulation. An examination of the lubricant-derived films using Raman and Auger electron spectroscopies found that the presence of more abundant amorphous carbon and lesser amounts of anti-wear film components on the surface was associated with higher wear. Copyright © 2009 John Wiley & Sons, Ltd. [source]

Mechanical properties of tribologically modified nanolayers

LUBRICATION SCIENCE, Issue 4 2005
D. Shakhvorostov
Abstract Wear in modern mechanical systems is characterised by ultra-low wear rates in the range of a few nanometres per hour. The surfaces of the materials involved, as well as their volumes, experience modifications as regards morphology, crystalline arrangement, and chemical bonds. The depth of the tribological interactions under given conditions extends to a micrometre or less. To probe these thin modified zones, synchrotron-based X-ray diffraction and nano-indentation were applied. The specimens were taken from tribometer experiments employing the radionuclide technique to measure ultra-low wear rates. To obtain different degrees of tribological interaction, various loads and sliding velocities were applied. The specimens were subdivided according to the total power dissipated during the tribometer experiment. [source]

Influence of Normal Force and Humidity on the Friction and Wear of Unlubricated Reciprocating Sliding Steel/Steel Couples

LUBRICATION SCIENCE, Issue 4 2004
D. Klaffke
Abstract The friction and wear behaviour of different steel/steel couples was investigated in laboratory tests with unlubricated reciprocating sliding motion. Two different steel balls were tested against two different steel discs in dry, normal, and moist air at room tem-perature. The influence of normal force on friction and wear was studied in the range from 1 to 10 N for all three levels of relative humidity (RH). RH strongly influenced wear behaviour for all four couples, while the friction behaviour was less affected by RH. For all the couples, normal force was found to influence wear rate with a tendency for the wear rate to increase with decreasing normal force. The coefficient of friction also increased with decreasing normal force, but to a much lesser extent than that evaluated for the wear rate. [source]

Influence of Temperature and Relative Humidity on the Friction and Wear of Unlubricated Reciprocating Sliding Steel/ Steel Couples

LUBRICATION SCIENCE, Issue 4 2004
D. Klaffke
Abstract Many tribosystems are subjected to different conditions with respect to temperature and humidity. Reciprocating sliding tests with steel/steel couples were performed using a laboratory test rig in air with varying relative humidity and temperature. During each test the friction force, the total linear wear, the electrical contact resistance, and the acoustic emission were recorded. Tests with self-mated couples of bearing steel (100r6) and of stainless steel (X10CrNiMoNb18-10/X5CrNi18-9) in a ball-on-disc arrangement revealed small effects of temperature and humidity on friction, but a strong effect of the water vapour content on the wear rate of the system. Attempts were made to correlate changes of wear behaviour with different wear mechanisms. [source]

Abrasive Wear of DLC/PVD Multilayer Coatings: AFM Studies

LUBRICATION SCIENCE, Issue 3 2004
C. Martini
Abstract The tribological behaviour of multilayered coatings deposited on plain carbon steel was investigated by microscale abrasion tests (MSATs). The multilayered coatings consisted of an outer diamond-like carbon (DLC) layer, a physical vapour deposition (PVD) nitride-based interlayer, and an inner electroless Ni-P layer. PVD TiN- and Ti(C,N)-coated samples with and without the DLC outer layer were studied in order to evaluate the influence of each layer on the tribological behaviour of the multilayer-coated system. The MSATs were carried out using a device based on ball-cratering geometry: a hard steel sphere was rotated against the coated specimen in the presence of an aqueous suspension of SiC particles. The wear coefficients of the multilayers were calculated from the diameter of the wear craters. The morphology of the wear scars produced by the MSATs was studied by atomic force microscopy (AFM). The wear damage was described by measuring the r.m.s. roughness (Sq) on the sides of the wear craters. Roughness values were related to the wear coefficients (kc) for the different multilayers on the basis of mathematical elaboration typical of the ,design of experiment' (DOE) statistical technique. The presence of the DLC outer layer reduced the roughness of the crater sides and significantly increased the wear resistance of the multilayer only in the case of the PVD TiN sublayer. [source]

An Approach to Calculating Wear on Annular Non-Return Valves

MACROMOLECULAR MATERIALS & ENGINEERING, Issue 11 2002
Helmut Potente
Abstract The serviceability of non-return valves has a major influence on the productivity of the injection molding process. During a meeting of experts held at our Institute, it was seen that closing behavior and wear are the key problems encountered in practice. The conducted investigations to tackle these questions have shown that both an improved closing behavior and a lower level of wear can be achieved by reducing the inside radius of the locking ring. Pressure profile over the length of a non-return valve (n,=,0.4; ,=,25,000 mm3/s). [source]

Wear and microstructural characteristics of spray atomized zircon sand reinforced LM13 alloy.

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, Issue 7 2010
Verschleiß- und Gefügecharakteristik von sprühkompaktierter mit Zirkoniumsand verstärkter LM13 Legierung
Verbundwerkstoff; Aluminiummatrix; Sprühkompaktieren; Verschleißverhalten Abstract The requirement of the high performance light weight materials demands the development of varieties of materials within the economical range to get it commercialized. Light weight aluminium alloys are used in several structural applications like automotive, aerospace, defense industry and other fields of engineering. The ceramic particle reinforced aluminium metal matrix composites (AMCs) have emerged as a suitable candidate for commercial applications. A variety of processing routes have been adopted to manufacture AMCs. In the present work LM13 alloy reinforced with zircon sand is formed via spray forming. During experimentation a self prepared convergent-divergent nozzle is used for inert gas atomization of the melt which is subsequently deposited on copper substrate placed vertically below the atomizer. The zircon sand particles are injected in the atomization zone by external injectors aligned perpendicular to the gas atomization axis. Zircon sand has been found to have new promising economical commercial candidate due to its easy availability and good mechanical properties like high hardness, high modulus of elasticity and good thermal stability. The microhardness of cast alloy and spray formed composite shows that the spray formed zircon sand reinforced composite has higher hardness. Also the lower wear rate has been observed in case of the zircon sand reinforced AMC as compared to LM13 alloy. This behaviour is further analyzed in light of microstructural features of the spray deposited composite using optical and scanning electron microscope (SEM). A comparative study of this material (LM13/Zircon sand) with the parent alloy (LM13) is presented in this work. [source]

Verschleißreduzierung in hydraulischen Verdrängereinheiten durch Verwendung PVD-beschichteter Komponenten

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, Issue 10-11 2004
H. Murrenhoff
Wear; hydraulic system; PVD coating Abstract In hydrostatischen Verdrängereinheiten sind Komponenten und mineralölbasierte, meist hochadditivierte, Fluide für einen optimalen Betrieb aufeinander abgestimmt. Ein Wechsel zu niedrig oder unadditivierten Druckübertragungsmedien bedeutet den Verlust wichtiger Funktionsträger in den verschiedenen Tribokontakten. Im SFB 442 ,Umweltverträgliche Tribosysteme" wird dies durch die Übertragung der entsprechenden Funktionen auf die PVD-beschichteten Kontaktflächen kompensiert. Dabei werden gradierte Kohlenstoffschichten verwendet. Auf verschiedenen Prüfständen sind dabei maßgebliche Fortschritte beim Einsatz beschichteter Tribokontaktkörper gemacht worden. Wear reduction with PVD-coatings in hydrostatic displacement units Hydrostatic pumps and motors are most important parts of hydraulic systems. The majority of these systems is designed to be used with fluids, which are based on mineral oil and improved by numerous additives. These systems are a rather optimal synthesis of fluid and solids, developed in this unity to a high performing standard. A change to fluids, which are environmentally friendly, means the loss of environmental harmful additivs and though, among other things, an increasing friction and wear of the system. To compensate this loss of technically helpful additivs, their tribological functions have to be transferred to the surface of the solid parts. That may be done with coating the surfaces of the tribological contacts with PVD-coatings, like those based on ZrC-materials. Experiments on speciments and pistons have shown the potential of that method. [source]

Wear and corrosion behavior of W/WC bilayers deposited by magnetron sputtering

PHYSICA STATUS SOLIDI (C) - CURRENT TOPICS IN SOLID STATE PHYSICS, Issue 11 2007
N. A. de Sánchez
Abstract WC/W coatings were deposited by reactive magnetron sputtering using 40%, 60% and 80% methane CH4 in the gas mixture. The bilayers were grown on to AISI 420 stainless-steel substrates in order to study the wear and corrosion behavior. Before growing the bilayers, one Ti monolayer was grown to improve the adherence of the coatings to the substrate. The wear resistance and the friction coefficient of the coatings were determined using a pin-on-disk tribometer. All coatings had a friction coefficient of about 0.5. The measured weight lost of the bilayers from each probe allowed the qualitative analysis of wear behavior all coatings. The bilayers grown with 80% methane showed the best abrasive wear resistance and adhesion without failure through the coating in the wear track for dry pin-on-disk sliding. Electrochemical corrosion test showed that the bilayers grown with 80% methane were more resistant to corrosion than the ones uncoated. (© 2007 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source]

Engineering and Design of Wear and Corrosion Resistant PVD Coatings Regarding the Exceptional Properties of Magnesium Substrates

PLASMA PROCESSES AND POLYMERS, Issue S1 2007
Holger Hoche
Abstract Although magnesium alloys were popular in the first half of the 20th century, the bad corrosion properties prevented their breakthrough in industrial mass production. Since the technology for the production of high purity alloys was introduced in the 1970s, magnesium alloys became more and more in the focus of industrial attention. Today magnesium alloys are state-of-the-art in construction parts in automotive industry. Despite its outstanding properties like good castability, low density and nearly unlimited availability the negative aspects like weak corrosion and wear behaviour still limit the application of magnesiums in industry, due to the need of sufficient surface protection (E. Aghion, B. Bronfin, Mater. Sci. Forum2000, 350,351, 19). Today, plasma electrolytic anodisations are state-of-the-art (H. Haferkamp, "Magnesiumkorrosion,Prozesse, Schutz von Anode und Kathode", in: Moderne Beschichtungsverfahren, F.-W. Bach, T. Duda, Eds., Wiley-VCH, Weinheim 2000, ISBN 3-527-30117-8, 242; M. Thoma, Metalloberfläche1984, 38, 393; T. W. Jelinek, Galvanotechnik2003, 94, 46; A. Kuhn, Galvanotechnik2003, 94, 1114). They provide acceptable corrosion resistance and protect the magnesium from mechanical damage due to their high hardness. On the other hand, their high porosity limits their use in combination with electrochemically noble materials, leading to galvanic corrosion (J. Senf, "Untersuchung und Beschreibung von Magnesiumdruckgusslegierungen unter tribologischer, korrosiver und mechanisch-korrosiver Beanspruchung, Berichte aus der Werkstofftechnik", Shaker Verlag, Germany 2001, ISBN 3-8265-8428-7). In addition, the high surface roughness of the plasma electrolytic anodisations restricts their use in tribological applications, particularly under sliding conditions (H. Hoche, "Grundlegende Untersuchungen zur Entwicklung von PVD-Beschichtungen auf Magnesiumlegierungen im Hinblick auf die Erhöhung der Verschleißbeständigkeit und unter Berücksichtigung des Korrosionsverhaltens", Dissertation, TU-Darmstadt D17, Shaker Verlag, Germany 2004). In order to achieve smooth surfaces with high quality, the PVD technology moves into the centre of interest. Since the 1980s PVD coatings are well established and widely used for different industrial applications, mainly for steel and tool coatings. The authors were the first who carried out serious studies on the development of PVD coatings for magnesium alloys in 1999 (J. Senf, "Untersuchung und Beschreibung von Magnesiumdruckgusslegierungen unter tribologischer, korrosiver und mechanisch-korrosiver Beanspruchung, Berichte aus der Werkstofftechnik", Shaker Verlag, Germany 2001, ISBN 3-8265-8428-7; H. Hoche, "Grundlegende Untersuchungen zur Entwicklung von PVD-Beschichtungen auf Magnesiumlegierungen im Hinblick auf die Erhöhung der Verschleißbeständigkeit und unter Berücksichtigung des Korrosionsverhaltens", Dissertation, TU-Darmstadt D17, Shaker Verlag, Germany 2004). The extensive research activities lead to the recent development of a coating system, which provides both, good wear properties as well as good corrosion behaviour. [source]

Effect of different types of peroxides on properties of vulcanized EPDM + PP blends

POLYMER COMPOSITES, Issue 10 2010
Witold Brostow
Mechanical and tribological behavior of several dynamic vulcanizate blends of polypropylene (PP) with ethylene-propylene-diene rubber (EPDM) was examined and compared with those of uncrosslinked blends. Vulcanization was performed using two types of organic peroxides combined with (meth)acrylate coagent. The effect of different types and concentrations of peroxides as crosslinking agents on the properties of the resulting materials were investigated. Dicumyl peroxide (DCP) provides higher reactivity and exhibits nearly the same crosslinking efficiency for both 60/40 and 50/50 blends; almost fully crosslinked samples are obtained if the compound contains 1.0 or 2.0 wt% DCP. These results correlate to the gel content and mechanical properties of our materials. Variation of PP + elastomer ratio does not have a significant influence on friction. From 60/40 group of composites, lower friction values were obtained for samples cured with 0.5 wt% benzoyl peroxide (BP) and 1.0 wt% DCP. The tribological properties of the samples with higher amount of DCP show rubbery rather than a toughened thermoplastic behavior. Wear of the composites decreases with the increasing concentration of the curing agent. Compared to BP, the samples cured with DCP display lower wear. POLYM. COMPOS., 31:1678,1691, 2010. © 2010 Society of Plastics Engineers. [source]

Ceramic-On-Metal for Total Hip Replacement: Mixing and Matching Can Lead to High Wear

ARTIFICIAL ORGANS, Issue 4 2010
Saverio Affatato
Abstract Ceramic-on-ceramic and metal-on-metal bearing surfaces are often employed for total hip replacement because of their resistance to wear. However, they have some limits: brittleness is a major concern for ceramic, and ion release is a drawback for metal. To reduce the effect of these limitations, a hybrid coupling of ceramic-on-metal has been proposed. The theoretical advantage of this new coupling might lead orthopedic surgeons to use it indiscriminately. We asked whether the wear rate of this innovative solution was comparable with that of ceramic-on-ceramic, which is considered to be the gold standard for wear resistance. In a hip simulator study, we tested the wear pattern of a hybrid ceramic-on-metal coupling supplied by the same distributor; in particular, three different configurations were tested for 5 million cycles: 36-mm ceramic-on-ceramic, 32-mm and 36-mm ceramic-on-metal. These combinations were gravimetrically and geometrically evaluated. After 5 million cycles, the volumetric loss for the metal acetabular cups (, 36-mm) was 20-fold greater than that of the ceramic cups of the same size (, 36-mm); a volumetric loss of 4.35 mm3 and 0.26 mm3 was observed, respectively, for ceramic-on-metal and ceramic-on-ceramic combinations. Significant statistical differences were observed between all 36-mm different combinations (P < 0.0001). The increased diameter of the 36-mm ceramic-on-metal configuration resulted in a lower volumetric loss compared with that of the 32-mm ceramic-on-metal configuration. Our findings showed an increase in wear for the proposed hybrid specimens with respect to that of the ceramic-on-ceramic ones. This confirms that even in the case of ceramic-on-metal bearings, mixing and matching could not prove effective wear behavior, not even comparable with that of the ceramic-on-ceramic gold standard. [source]

Wear of the artificial hip joint material under lubrication

ASIA-PACIFIC JOURNAL OF CHEMICAL ENGINEERING, Issue 1 2009
E. P. J. Waters
Abstract A study of wear properties of hip-replacement materials, namely high-nitrogen stainless-steel femoral heads and ultra-high molecular weight polyethylene (UHMWPE), was conducted in a non-conforming apparatus using various liquid lubricants. The liquids used were normal saline solution, sodium azide solution, pure ethanol, aqueous hyaluronic acid and aqueous hyaluronic acid/cholesterol and cholesterol palmitate liquid crystal lubricant. Saline solution proved to be unsuitable as a lubricant while sodium azide that was used as a bactericide provided some evidence of mixed lubrication. A bactericide was included to overcome degradation. The aqueous hyaluronic acid exhibited cushion form lubrication as evidenced by retention of the original polymer surface features within the wear indent. Cholesterol addition showed little improvement on the wear properties but massively increased the bacterial activity. Again, inclusion of a bactericide was necessary. Liquid crystal lubricant significantly reduced wear and the atomic force microscope (AFM) showed that the liquid crystal formed protective layers on the counter face surfaces. The sub-surface of the polymer possessed plastic creep under load but low adhesive wear was present. There also was an absence of sub-micron polymer debris. It was concluded that a dramatic reduction in wear could be achieved by incorporation of liquid crystal lubricant in hip-replacement elements. Copyright © 2009 Curtin University of Technology and John Wiley & Sons, Ltd. [source]

Physical-mechanical properties of glass ionomer cements indicated for atraumatic restorative treatment

AUSTRALIAN DENTAL JOURNAL, Issue 3 2009
CC Bonifácio
Abstract Background:, This study evaluated mechanical properties of glass ionomer cements (GICs) used for atraumatic restorative treatment. Wear resistance, Knoop hardness (Kh), flexural (Fs) and compressive strength (Cs) were evaluated. The GICs used were Riva Self Cure (RVA), Fuji IX (FIX), Hi Dense (HD), Vitro Molar (VM), Maxxion R (MXR) and Ketac Molar Easymix (KME). Methods:, Wear was evaluated after 1, 4, 63 and 365 days. Two-way ANOVA and Tukey post hoc tests (P = 0.05) analysed differences in wear of the GICs and the time effect. Fs, Cs, and Kh were analysed with one-way ANOVA. Results:, The type of cement (p < 0.001) and the time (p < 0.001) had a significant effect on wear. In early-term wear and Kh, KME and FIX presented the best performance. In long-term wear, Fs and Cs, KME, FIX and HD had the best performance. Strong explanatory power between Fs and the Kh (r2 = 0.85), Cs and the Kh (r2 = 0.82), long-term wear and Fs of 24 h (r2 = 0.79) were observed. Conclusions:, The data suggested that KME and FIX presented the best in vitro performance. HD showed good results except for early-term wear. [source]

Hardware-Based Volumetric Knit-Wear

COMPUTER GRAPHICS FORUM, Issue 3 2002
Katja Daubert
We present a hardware-based, volumetric approach for rendering knit wear at very interactive rates. A single stitch is represented by a volumetric texture with each voxel storing the main direction of the strands of yarn inside it. We render the knit wear in layers using an approximation of the Banks model. Our hardware implementation allows specular and diffuse material properties to change from one voxel to the next. This enables us to represent yarn made up of different components or render garments with complicated color patterns. Furthermore, our approach can handle self-shadowing of the stitches, and can easily be adapted to also include view-independent scattering. The resulting shader lends itself naturally to mip-mapping, and requires no reordering of the base geometry, making it versatile and easy to use. Categories and Subject Descriptors (according to ACM CCS): I.3.3 [Computer Graphics]: Hardware Applications Volumetric Textures [source]

Use of mouthguards by basketball players in Victoria, Australia

DENTAL TRAUMATOLOGY, Issue 4 2003
Helen Cornwell
Abstract ,,,Basketball is a popular sport in Australia. Although orofacial injuries are common, mouthguard (MG) wear in basketball appears to be low. The purposes of this study were: to measure mouthguard wear by basketball players before and after a promotional intervention; to assess players' knowledge of the value of mouthguards for prevention of injury; and to describe their experience of orofacial injury. Two questionnaires (baseline and follow-up) were administered to a convenience sample of 496 basketball players in Victoria, Australia. Players recruited were youths (12,15-year olds, n = 208) and adults (18 years and over, n = 288), from all basketball levels (social to elite). Completion of the baseline questionnaire was followed immediately by an intervention comprising written and verbal information, a mouthguard blank and instructions on mouthguard construction. The follow-up questionnaire was mailed to all respondents 10,12 weeks later; 135 youths (65%) and 157 adults (54%) completed this. Mouthguard wear at baseline was low but was more frequent at games (62%) than at training (25%). Despite 90% of players acknowledging the protective value of a mouthguard, wear by youths did not increase following the intervention, and wear by adults increased by only 14% for training and 10% at games. Previous orofacial injury was recorded at baseline by 23% of players, but few had requested compensation from Basketball Australia (youths, 17%; adults, 30%). Two predictor variables were statistically identified as related to mouthguard wear: previous orofacial injury and age group. Mouthguard wear was significantly more frequent amongst players with previous injury; such players were 2.76 times more likely to be wearers than those without previous injury. Youths were 2.31 times more likely to wear mouthguards than adults. Only 34 players (12% of respondents at follow-up) had a mouthguard constructed from the blank provided. Although youth and adult groups differed, the overall extent of mouthguard use was disappointingly low. Despite wide recognition of mouthguard value, the intervention had little effect on promoting their use. [source]

Ultrastructural identification of the antennal gland complement in Siagona europaea Dejean 1826, a myrmecophagous carabid beetle

ACTA ZOOLOGICA, Issue 3 2005
Anita Giglio
Abstract We examined antennal exocrine glands in adults of a myrmecophagous carabid beetle, Siagona europaea Dejean 1826 (Coleoptera, Carabidae), by light and electron microscopy and we identified two types of integumentary glands. The first type includes glands formed by three cells (a secretory cell, an intercalary cell and a duct cell) known as class 3 of Noirot and Quennedey (1991). The secretory cell has several large multivesicular electron-lucent bodies, indicating a glycoprotein product associated with lipids. We hypothesize that this secretion protects the surface of antennae and sensilla from wear. The second group of glands includes unicellular glands known as oenocytes (class 2 of Noirot and Quennedey, 1991), which secrete epicuticular hydrocarbons through epidermal cells. [source]

Using age grading by wing injuries to estimate size-dependent adult survivorship in the field: a case study of the yellow dung fly Scathophaga stercoraria

ECOLOGICAL ENTOMOLOGY, Issue 5 2002
Dieter U. Burkhard
Abstract 1. Studies of natural selection depend on estimates of longevity and mortality in the wild. In small and mobile species such as insects, direct, mark,recapture (resight), studies are difficult to perform because individuals cannot be tracked easily. 2. It was investigated whether age grading based on wing injuries alone can be used to estimate size-specific survivorship in the field in the yellow dung fly Scathophaga stercoraria (L.) (Diptera: Scathophagidae). 3. The accumulation of different types of wing injury throughout the spring and autumn flight seasons for both sexes was recorded: tears, notches (both reflecting regular wear), and large missing areas (probably due to intra- and inter-specific interactions). 4. Female longevity increased with body size in both spring and autumn, whereas male longevity increased slightly with size in spring but decreased in autumn. 5. The two sexes and males of different size classes accumulated the various types of wing injury differentially, presumably due to differential patterns of intraspecific interactions. Additionally, body size exhibited a seasonal pattern, complicating interpretation of the relationship between body size and wing injuries. 6. It is therefore concluded that estimating adult viability selection on body size using wing injuries is problematic in dung flies, and potentially also in other species. It is suggested that before this method is applied in any particular species, pilot studies should be conducted to verify whether wing injuries accumulate equally in all classes of individuals of interest. In addition, it is necessary to investigate the causes of different types of wing injury. [source]

Equine dental disease Part 3: a long-term study of 400 cases: disorders of wear, traumatic damage and idiopathic fractures, tumours and miscellaneous disorders of the cheek teeth

EQUINE VETERINARY JOURNAL, Issue 1 2000
P. M. Dixon
Summary Of 400 horses referred because of dental disorders, 349 cases were diagnosed as suffering from primary disorders of their cheek teeth. Details of 104 of these cases are presented, including 44 cases with abnormalities of wear, 26 cases with traumatic damage, 24 cases with idiopathic fractures and 10 cases with miscellaneous cheek teeth disorders including oral tumours. The long-term response to treatment was excellent in most cases, even in cases with residual secondary periodontal disease. [source]