			Home About us Contact

Voltage Deviation (voltage + deviation)

Distribution by Scientific Domains

Engineering	83%

Distribution within Engineering

Power Technology & Power Engineering	60%
General & Introductory Electrical & Electronics Engineering	39%

Selected Abstracts

Coordinated voltage control of transformer taps with provision for hierarchical structure in power system

ELECTRICAL ENGINEERING IN JAPAN, Issue 4 2009
Yoshiki Nakachi
Abstract Participation of distributed generators (DGs), such as wind turbines, cogeneration systems, etc., is a natural trend from an ecological point of view and will continue to increase. The outputs of these DGs mainly depend on weather conditions but do not correspond to the changes of electrical load demand necessarily. On the other hand, due to deregulation of the electric power market, the power flow in a power system will uncertainly vary with several power transactions. Thus, complex power flow by DGs or transactions will cause voltage deviation. It will be difficult to sustain the voltage quality by using conventional voltage/reactive power control in the near future. In this paper, in order to avoid such voltage deviation and to decrease the frequency of transformer tap operations, the coordinated voltage control scheme of transformer taps on account of hierarchical structure in the power system is proposed. In the proposed scheme, integral of voltage deviation at each layer bus is applied to decide the timing of each transformer tap operation. Numerical simulations confirm that the proposed scheme is able to respond to every condition on voltage deviation. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 166(4): 48,55, 2009; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/eej.20531 [source]

Simple circuit to improve electric field homogeneity in contour-clamped homogeneous electric field chambers

ELECTROPHORESIS, Issue 7-8 2003
José A. Herrera
Abstract We redesigned contour-clamped homogeneous electric field (CHEF) circuitry to eliminate crossover distortion, to set identical potentials at electrodes of each equipotential pair and to drive pairs with transistors in emitter follower stages. An equipotential pair comprised the two electrodes set at the same potential to provide electric field homogeneity inside of the hexagonal array. The new circuitry consisted of two identical circuits, each having a resistor ladder, diodes and transistors. Both circuits were interconnected by diodes that controlled the current flow to electrodes when the array was energized in the ,A' or ,B' direction of the electric field. The total number of transistors was two-thirds of the total number of electrodes. Average voltage deviation from potentials expected at electrodes to achieve a homogeneous electric field was 0.06 V, whereas 0.44 V was obtained with another circuit that used transistors in push-pull stages. The new voltage clamp unit is cheap, generated homogeneous electric field, and gave reproducible and undistorted DNA band patterns. [source]

Optimal Control of Voltage in Distribution Systems by Voltage Reference Management

IEEJ TRANSACTIONS ON ELECTRICAL AND ELECTRONIC ENGINEERING, Issue 5 2009
Tomonobu Senjyu Student member
Abstract Recently, renewable energy technologies such as wind turbine generators and photovoltaic (PV) systems have been introduced as distributed generations (DGs). Connections of a large amount of distributed generations may cause voltage deviation beyond the statutory range in distribution systems. A reactive power control of DGs can be a solution of this problem, and it also has a possibility to reduce distribution loss. In this paper, we propose a control methodology of voltage profile in a distribution system using reactive power control of inverters interfaced with DGs and tap changing transformers. In the proposed method, a one-day schedule of voltage references for the control devices are determined by an optimization technique based on predicted values of load demand and PV power generation. Reactive power control of interfaced inverters is implemented within the inverter capacity without reducing active power output. The proposed method accomplishes voltage regulation within the acceptable range and reduction of distribution loss. The effectiveness of the proposed method is confirmed by simulations. Copyright © 2009 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc. [source]

Maintaining the power balance in an ,empty network'

EUROPEAN TRANSACTIONS ON ELECTRICAL POWER, Issue 5 2006
M. Reza
Abstract This paper presents the concept of an ,empty network' and shows how the power balance can be maintained in such a system. In this study, an ,empty network' is defined as a power system in which no rotating mass is present; all generators are grid-connected via power electronic interfaces. One generator creates a neat 50,Hz voltage that serves as a frequency reference for the other generators. Consequently, a power unbalance cannot be detected in the classical way, as an altered system frequency. Therefore, in this paper, voltage deviations are used to detect the power unbalances. Simple test systems that consist of 1, 2 and 3 buses are applied on a real time digital simulator (RTDS). A load jump is simulated to cause a power unbalance in the system. The study shows that by using voltage deviations as control signals, the power balance can be maintained in an empty network. Copyright © 2006 John Wiley & Sons, Ltd. [source]

Improvement of interactions among facts controls

EUROPEAN TRANSACTIONS ON ELECTRICAL POWER, Issue 5 2000
X. Lei
Interaction among the FACTS (flexible AC transmission systems) devices in a multi-machine system can adversely influence the damping properties of individual FACTS devices. In some critical cases, it may even amplify power swings or increase voltage deviations. This paper presents a global tuning method for the FACTS controllers in a multi-machine system. Based on a non-linear optimization algorithm implemented in a simulation program, the parameter settings of the FACTS controllers involved can be simultaneously optimized at transient conditions in coping with the non-linear nature of the power system. By minimizing a non-explicit target function in which swing characteristics between areas are included, interactions among the FACTS controls at transient conditions in the multi-machine system are minimized. Two multi-machine power systems equipped individually with a TCSC (thyristor-controlled series compensator) and a SVC (static Var compensator) are applied to demonstrate the efficiency of the proposed tuning procedure. The results obtained from simulations validate the improvement in damping of overall power oscillations. The simulations also show that the optimized FACTS controllers are robust in providing adequate damping for a range of conditions on the system. [source]

A method for fast simulation of multiple catastrophic faults in analogue circuits

INTERNATIONAL JOURNAL OF CIRCUIT THEORY AND APPLICATIONS, Issue 3 2010
Micha, Tadeusiewicz
Abstract The paper offers an efficient method for simulation of multiple catastrophic faults in linear AC circuits. The faulty elements are either open circuits or short circuits. The method exploits the well-known Householder formula in matrix theory to find the node voltages deviations due to the perturbations of some circuit elements. The main achievement of the paper is a systematic method for performing the simulation of all combinations of the multiple catastrophic faults. The method includes two new procedures enabling us to find very efficiently the node impedance matrix of the nominal circuit and inverses of some matrices corresponding to different fault combinations. The procedures are the crucial point of this approach and make it very efficient. Consequently, the amount of the computing power needed to carry out all the simulations is significantly reduced. Numerical examples illustrating the proposed approach are provided. Copyright © 2008 John Wiley & Sons, Ltd. [source]