Home About us Contact
|
Home About us Contact | ||
|
|
||
Velocity Values (velocity + value)
Selected AbstractsThe resistance of packed beds of moth gram (Vigna aconitifolius) to airflowINTERNATIONAL JOURNAL OF FOOD SCIENCE & TECHNOLOGY, Issue 5 2006Prabhakar M. Nimkar Summary The resistance of packed beds of clean moth gram (Vigna aconitifolius) to airflow was studied at moisture contents varying from 5.64 to 19.42% dry basis (d.b.) and at superficial air velocities ranging between 0.0104 and 0.8321 m s,1 with bed depths of 0.2,0.6 m and bulk densities ranging from 745 to 875 kg m,3. The airflow resistance of moth gram increased with increase in airflow rate and bulk density and decreased with moisture content. Results indicated that a 13.78% increase in moisture content decreased the pressure drop by 26.58% whereas, a 7.7% increase in bulk density increased the pressure drop by 43%. The modified Shedd's equation and Hukill and Ives equation were evaluated to see if they predicted pressure drop accurately. Airflow resistance was accurately described by the modified Shedd's equation. The statistical model that related airflow rate and bulk density could fit pressure drop data reasonably well. For loose fill beds an increase in grain moisture content increased the minimum fluidization velocity value from 1.1009 to 1.2391 m s,1 whereas, for grain beds with 12.47% moisture content, the increase in bulk density decreased the minimum fluidization velocity value from 1.1152 to 1.0306 m s,1. [source] Shear wave velocity model of the Santiago de Chile basin derived from ambient noise measurements: a comparison of proxies for seismic site conditions and amplificationGEOPHYSICAL JOURNAL INTERNATIONAL, Issue 1 2010Marco Pilz SUMMARY We determined a high-resolution 3-D S -wave velocity model for a 26 km × 12 km area in the northern part of the basin of Santiago de Chile. To reach this goal, we used microtremor recordings at 125 sites for deriving the horizontal-to-vertical (H/V) spectral ratios that we inverted to retrieve local S -wave velocity profiles. In the inversion procedure, we used additional geological and geophysical constraints and values of the thickness of the sedimentary cover already determined by gravimetric measurements, which were found to vary substantially over short distances in the investigated area. The resulting model was derived by interpolation with a kriging technique between the single S -wave velocity profiles and shows locally good agreement with the few existing velocity profile data, but allows the entire area, as well as deeper parts of the basin, to be represented in greater detail. The wealth of available data allowed us to check if any correlation between the S -wave velocity in the uppermost 30 m (v30S) and the slope of topography, a new technique recently proposed by Wald and Allen, exists on a local scale. We observed that while one lithology might provide a greater scatter in the velocity values for the investigated area, almost no correlation between topographic gradient and calculated v30S exists, whereas a better link is found between v30S and the local geology. Finally, we compared the v30S distribution with the MSK intensities for the 1985 Valparaiso event, pointing out that high intensities are found where the expected v30S values are low and over a thick sedimentary cover. Although this evidence cannot be generalized for all possible earthquakes, it indicates the influence of site effects modifying the ground motion when earthquakes occur well outside of the Santiago basin. [source] Three-dimensional seismic structure beneath the Australasian region from refracted wave observationsGEOPHYSICAL JOURNAL INTERNATIONAL, Issue 3 2000Y. Kaiho The earthquakes in the seismicity belt extending through Indonesia, New Guinea, Vanuatu and Fiji to the Tonga,Kermadec subduction zone recorded at the 65 portable broad-band stations deployed during the Skippy experiment from 1993,1996 provide good coverage of the lithosphere and mantle under the Australian continent, Coral Sea and Tasman Sea. The variation in structure in the upper part of the mantle is characterized by deter-mining a suite of 1-D structures from stacked record sections utilizing clear P and S arrivals, prepared for all propagation paths lying within a 10° azimuth band. The azimuth of these bands is rotated by 20° steps with four parallel corridors for each azimuth. This gives 26 separate azimuthal corridors for which 15 independent 1-D seismic velocity structures have been derived, which show significant variation in P and S structure. The set of 1-D structures is combined to produce a 3-D representation by projecting the velocity values along the ray path using a turning point approximation and stacking into 3-D cells (5° by 50 km in depth). Even though this procedure will tend to underestimate wave-speed perturbations, S -velocity deviations from the ak135 reference model exceed 6 per cent in the lithosphere. In the uppermost mantle the results display complex features and very high S -wave speeds beneath the Precambrian shields with a significant low-velocity zone beneath. High velocities are also found towards the base of the transition zone, with highS -wave speeds beneath the continent and high P -wave speeds beneath the ocean. The wave-speed patterns agree well with independent surface wave studies and delay time tomography studies in the zones of common coverage. [source] Sequential integrated inversion of refraction and wide-angle reflection traveltimes and gravity data for two-dimensional velocity structuresGEOPHYSICAL JOURNAL INTERNATIONAL, Issue 3 2000Rosaria Tondi A new algorithm is presented for the integrated 2-D inversion of seismic traveltime and gravity data. The algorithm adopts the ,maximum likelihood' regularization scheme. We construct a ,probability density function' which includes three kinds of information: information derived from gravity measurements; information derived from the seismic traveltime inversion procedure applied to the model; and information on the physical correlation among the density and the velocity parameters. We assume a linear relation between density and velocity, which can be node-dependent; that is, we can choose different relationships for different parts of the velocity,density grid. In addition, our procedure allows us to consider a covariance matrix related to the error propagation in linking density to velocity. We use seismic data to estimate starting velocity values and the position of boundary nodes. Subsequently, the sequential integrated inversion (SII) optimizes the layer velocities and densities for our models. The procedure is applicable, as an additional step, to any type of seismic tomographic inversion. We illustrate the method by comparing the velocity models recovered from a standard seismic traveltime inversion with those retrieved using our algorithm. The inversion of synthetic data calculated for a 2-D isotropic, laterally inhomogeneous model shows the stability and accuracy of this procedure, demonstrates the improvements to the recovery of true velocity anomalies, and proves that this technique can efficiently overcome some of the limitations of both gravity and seismic traveltime inversions, when they are used independently. An interpretation of field data from the 1994 Vesuvius test experiment is also presented. At depths down to 4.5 km, the model retrieved after a SII shows a more detailed structure than the model obtained from an interpretation of seismic traveltime only, and yields additional information for a further study of the area. [source] Three-dimensional VP and VP,/VS models of the upper crust in the Friuli area (northeastern Italy)GEOPHYSICAL JOURNAL INTERNATIONAL, Issue 2 2000G. F. Gentile 3-D images of P velocity and P - to S -velocity ratio have been produced for the upper crust of the Friuli area (northeastern Italy) using local earthquake tomography. The data consist of 2565 P and 930 S arrival times of high quality. The best-fitting VP and VP,/VS 1-D models were computed before the 3-D inversion. VP was measured on two rock samples representative of the investigated upper layers of the Friuli crust. The tomographic VP model was used for modelling the gravity anomalies, by converting the velocity values into densities along three vertical cross-sections. The computed gravity anomalies were optimized with respect to the observed gravity anomalies. The crust investigated is characterized by sharp lateral and deep VP and VP,/VS anomalies that are associated with the complex geological structure. High VP,/VS values are associated with highly fractured zones related to the main faulting pattern. The relocated seismicity is generally associated with sharp variations in the VP,/VS anomalies. The VP images show a high-velocity body below 6 km depth in the central part of the Friuli area, marked also by strong VP,/VS heterogeneities, and this is interpreted as a tectonic wedge. Comparison with the distribution of earthquakes supports the hypothesis that the tectonic wedge controls most of the seismicity and can be considered to be the main seismogenic zone in the Friuli area. [source] Ineffective Peripheral Tissue Perfusion: Clinical Validation in Patients With Hypertensive CardiomiopathyINTERNATIONAL JOURNAL OF NURSING TERMINOLOGIES AND CLASSIFICATION, Issue 2 2006Rita de Cassia Gengo de Silva MS PURPOSE.,To validate defining characteristics of ineffective peripheral tissue perfusion using vasomotor function assessment. METHODS.,Twenty-four patients with hypertensive cardiomiopathy were evaluated for 18 defining characteristics of ineffective peripheral tissue perfusion and underwent vasomotor function assessment with induction of reactive hyperemia, intra-arterial infusion of acetylcholine, and pulse wave velocity measurement. The Student's t test and Kruskall,Wallis test were used to assess the significance of relationships between defining characteristics and vasomotor function data. FINDINGS.,Diminished lower extremity pulses were associated with diminished forearm blood flow during acetylcholine infusion; left ventricular overload, intermittent claudication, and diminished skin moisture were associated with elevated pulse wave velocity values. CONCLUSION.,The defining characteristics of ineffective peripheral tissue perfusion were highly associated with vasomotor function data as "gold standards" for that diagnosis. PRACTICE IMPLICATIONS.,Nurses should be able to accurately assess diminished lower extremity pulses, intermittent claudication, and diminished skin moisture as relevant characteristics of ineffective peripheral tissue perfusion in patients with hypertensive cardiomiopathy. Irrigation Tissulaire Périphérique Inefficace: Validation Clinique Chez les Patients Atteints de Cardiomyopathie Hypertensive BUT.,Valider les caractéristiques de Irrigation tissulaire périphérique inefficace en utilisant l'évaluation de la fonction vasomotrice. MÉTHODES.,Vingt-quatre patients souffrant de cardiomyopathie hypertensive furent évalués au regard des 18 caractéristiques du diagnostic Irrigation vasculaire périphérique inefficace et de la fonction vasomotrice par induction d'une hyperémie réactionnelle, la perfusion intra-artérielle d'acétylcholine, et la mesure de la vélocité de l'onde du pouls. Les tests "Student t et Kruskall,Wallis" furent utilisés pour déterminer l'importance des liens entre les caractéristiques et les valeurs de la fonction vasomotrice. RÉSULTATS.,La diminution des pulsations périphériques des membres inférieurs fut associée à une diminution du flot sanguin pendant la perfusion d'acétylcholine; une surcharge ventriculaire gauche, de la claudication intermittente et une diminution de l'hydratation de la peau furent associées à des valeurs élevées de la vélocité de l'onde du pouls. CONCLUSION.,,Les caractéristiques de Irrigation tissulaire périphérique inefficace qui furent associées de manière significative à la fonction vasomotrice peuvent être considérées comme les "étalons or" de ce diagnostic. IMPLICATIONS POUR LA PRATIQUE.,Les infirmières devraient être capables d'évaluer correctement la diminution des pouls périphériques, la claudication intermittente, et la diminution de l'hydratation de la peau, car ce sont des caractéristiques pertinentes de l'irrigation tissulaire périphérique inefficace chez les patients atteints de cardiomyopathie hypertensive. Translation by Cécile Boisvert, MSN, RN Perfusão Tissular Periférica Ineficaz: Validação Clínica em Pacientes com Miocardiopatia Hipertensiva PROPÓSITO.,Validar as caraterísticas definidoras do diagnóstico de perfusão tissular periférica ineficaz usando a avaliação da função vasomotora. MÉTODO.,Vinte e quatro pacientes com miocardiopatia hipertensiva foram avaliados segundo 18 características definidoras de perfusão tissular periférica ineficaz e submetidos a avaliação da função vasomotora por indução de hiperemia reativa, infusão intra-arterial de acetilcolina e por mensuração da velocidade da onda de pulso. Testes T de Student e de Kruskall,Wallis foram aplicados para avaliar a significância das relações entre as características definidoras e os dados da função vasomotora. RESULTADOS.,Diminuição de pulso nas extremidades inferiores foi associada com o menor fluxo de sangue no antebraço durante a infusão de acetilcolina; sobrecarga ventricular esquerda, claudicação intermitente e diminuição da hidratação da pele foram associados com valores elevados de velocidade de onda de pulso. CONCLUSÃO.,Quatro características definidoras de perfusão tissular periférica ineficaz foram altamente associadas com função vasomotora alterada como "padrão ouro" para este diagnóstico. IMPLICAÇÕES PARA A PRÁTICA.,As enfermeiras devem ser capazes de avaliar com precisão a diminuição dos pulsos das extremidades inferiores, claudicação intermitente e diminuição na hidratação da pele como características definidoras relevantes da perfusão tissular periférica ineficaz em pacientes com miocardiopatia hipertensiva. Translation by Alba Leite de Barros, PhD, RN Perfusión Tisular Periférica Inefectiva: Validación Clínica en Pacientes que Presentan Miocardiopatía Hipertensiva PROPÓSITO.,Validar las características definitorias del diagnóstico Perfusión tisular periférica inefectiva utilizando una valoración de la función vasomotora. METODOLOGÍA.,Veinticuatro pacientes diagnosticados de Miocardiopatía Hipertensiva fueron evaluados con respecto a las 18 características definitorias del diagnóstico Perfusión tisular periférica inefectiva y sometidos a una valoración de la función vasomotora con inducción de Hiperemia reactiva, infusión intra-arterial de acetilcolina, y medida de la velocidad de la onda del pulso. Se utilizaron los análisis estadísticos de t-Student y Kruskall,Wallis para valorar el significado de las relaciones entre las características definitorias y los datos obtenidos de la valoración de la función vasomotora. HALLAZGOS.,Durante la infusión de acetilcolina se detectó disminución de los pulsos en la extremidad inferior relacionado con la disminución del volumen de sangre en el antebrazo; la sobrecarga ventricular izquierda, claudicación intermitente y disminución de la hidratación de la piel fueron asociadas con la elevación de los valores de la velocidad de la onda del pulso. CONCLUSIÓN.,Las características definitorias del diagnóstico Perfusión tisular periférica inefectiva estaban fuertemente asociadas a los datos procedentes de la valoración de la función vasomotora identificándose como "estándares fundamentales" para este diagnóstico. IMPLICACIONES PARA LA PRÁCTICA.,Las enfermeras deberían ser capaces de valorar cuidadosamente la presencia de pulsos disminuidos en las extremidades inferiores, y la disminución de la hidratación de la piel ya que son características relevantes del diagnóstico Perfusión tisular periférica inefectiva en pacientes que presentan Miocardiopatía Hipertensiva. Translation by Adolf Guirao, RN [source] Calcium Accretion in Girls and Boys During Puberty: A Longitudinal AnalysisJOURNAL OF BONE AND MINERAL RESEARCH, Issue 11 2000Donald A. Bailey Abstract The primary purpose of this study was to estimate the magnitude and variability of peak calcium accretion rates in the skeletons of healthy white adolescents. Total-body bone mineral content (BMC) was measured annually on six occasions by dual-energy X-ray absorptiometry (DXA; Hologic 2000, array mode), a BMC velocity curve was generated for each child by a cubic spline fit, and peak accretion rates were determined. Anthropometric measures were collected every 6 months and a 24-h dietary recall was recorded two to three times per year. Of the 113 boys and 115 girls initially enrolled in the study, 60 boys and 53 girls who had peak height velocity (PHV) and peak BMC velocity values were used in this longitudinal analysis. When the individual BMC velocity curves were aligned on the age of peak bone mineral velocity, the resulting mean peak bone mineral accrual rate was 407 g/year for boys (SD, 92 g/year; range, 226,651 g/year) and 322 g/year for girls (SD, 66 g/year; range, 194,520 g/year). Using 32.2% as the fraction of calcium in bone mineral, as determined by neutron activation analysis (Ellis et al., J Bone Miner Res 1996;11:843-848), these corresponded to peak calcium accretion rates of 359 mg/day for boys (81 mg/day; 199,574 mg/day) and 284 mg/day for girls (58 mg/day; 171,459 mg/day). These longitudinal results are 27,34% higher than our previous cross-sectional analysis in which we reported mean values of 282 mg/day for boys and 212 mg/day for girls (Martin et al., Am J Clin Nutr 1997;66:611-615). Mean age of peak calcium accretion was 14.0 years for the boys (1.0 years; 12.0-15.9 years), and 12.5 years for the girls (0.9 years; 10.5-14.6 years). Dietary calcium intake, determined as the mean of all assessments up to the age of peak accretion was 1140 mg/day (SD, 392 mg/day) for boys and 1113 mg/day (SD, 378 mg/day) for girls. We estimate that 26% of adult calcium is laid down during the 2 adolescent years of peak skeletal growth. This period of rapid growth requires high accretion rates of calcium, achieved in part by increased retention efficiency of dietary calcium. [source] Fast GC analysis with a 50 ,m ID column: theory, practical aspects, and application to a highly complex sampleJOURNAL OF SEPARATION SCIENCE, JSS, Issue 14 2004Luigi Mondello Abstract This research focuses on the minimization of GC analysis times through the use of a 5 m×0.05 mm ID×0.05 ,m (film thickness) column. Experimental minimum plate height (Hmin) and optimum linear velocity values were derived from standard compound applications, under various analytical conditions, and then related to classical chromatographic theory. Deviations from the latter are measured and discussed. Practical aspects linked to the use of such capillaries, such as column sample capacity and detector acquisition rates, are also considered. Furthermore, a fast, and what can be considered a very fast method, were applied to the separation of a fuel sample. Coefficients of variation of elution times and relative peak areas were calculated in the very fast application. All analytical results are compared with those obtained by conventional 0.25 mm ID column applications. [source] Simultaneous Measurement of Particle Size and Particle Velocity by the Spatial Filtering Technique,PARTICLE & PARTICLE SYSTEMS CHARACTERIZATION, Issue 6 2002Dieter Petrak Abstract The objective of this study was to compare the measuring results of a fiber-optical probe based on a modified spatial filtering technique with given size distributions of different test powders and also with particle velocity values of laser Doppler measurements. Fiber-optical spatial filtering velocimetry was modified by fiber-optical spot scanning in order to determine simultaneously the size and the velocity of particles. The fiber-optical probe system can be used as an in-line measuring device for sizing of particles in different technical applications. Spherical test particles were narrow-sized glass beads in the range 30,100,,m and irregularly shaped test particles were limestone particles in the range 10,600,,m. Particles were dispersed by a brush disperser and the measurements were carried out at a fixed position in a free particle-laden air stream. Owing to the measurement of chord lengths and to the influence of diffraction and divergent angle, the probe results show differences from the given test particle sizes. Owing to the particle-probe collisions, the mean velocity determined by the probe is smaller than the laser Doppler mean velocity. [source] Growth and long-term lung function in cystic fibrosis: A longitudinal study of patients diagnosed by neonatal screeningPEDIATRIC PULMONOLOGY, Issue 3 2009Baroukh Maurice Assael MD Abstract Objective So far there is no long-term analysis relating the achievement of growth milestones (such as prepubertal and pubertal take-off and peak velocity) to the course of respiratory function from childhood to adulthood in cystic fibrosis. This study was designed to evaluate linear growth and severity of lung disease, find a correlation between growth and disease severity throughout childhood. Patients One hundred sixty-three patients from one center were selected according to: diagnosis by neonatal screening, complete follow-up available (four height measurements/year) until the age of 20, respiratory tests available from the age of 5,6 years until adulthood, lung transplantation, or death. Disease was classified as mild or severe according to FEV1 (group 1 and group 2). A third group of patients (group 3) consisted of those who died or underwent lung transplantation before the age of 18. Methods Individual growth profiles were fitted with a seven-constant nonlinear growth function. A multivariate linear model was fitted, with gender and severity of disease as covariates, and age, height, and height velocity at growth milestones as dependent variables. Data were compared with those of the normal Italian population. Results Lung disease severity correlates with delayed prepubertal and pubertal growth milestones. Peak height velocities were significantly reduced in relation to the severity of the disease. Conclusions Patients with severe forms of cystic fibrosis exhibit reduced growth velocity values at an early age, before a clear decline in pulmonary function. Pediatr Pulmonol. 2009; 44:209,215. © 2009 Wiley-Liss, Inc. [source] Preparation and characterization of nylon 6/organoclay nanocomposite filament fibersPOLYMER COMPOSITES, Issue 3 2009Kap Jin Kim A series of nylon 6 (NY6)/organoclay nanocomposites were prepared via in situ polymerization of ,-caprolactam in the presence of 1,2-aminododecanoic acid-intercalated montmorillonite (ADA-MMT) organoclay (1,5 wt%) using 6-aminocaproic acid as polymerization catalyst. The extent of organoclay dispersion in NY6 matrix was analyzed using WAXD and SEM measurements. DSC studies revealed marginal shift in melting and melt-crystallization peaks toward lower temperature with increasing clay content. Melt viscosity studies for NY6/ADA-MMT exhibited higher shear-thinning behavior than neat NY6 probably due to the slip between NY6 matrix and exfoliated organoclay platelets during shear flow. The prepared nanocomposites were melt-spun and studied for their property improvements against varying clay content, draw ratios, and annealing conditions. Birefringence and sonic velocity values increased initially at lower draw ratios (,2.5) due to increased orientation of molecular chains along the drawing direction but saturated at higher draw ratio (3.0) for all the samples. At the same draw ratio; compared to neat NY6, NY6/organoclay fibers showed increased chain orientation along the drawing direction which can be attributed to the "tethering effect" of organoclay on NY6 matrix. The initial modulus and stress at break were sensitive to factors such as draw ratio, clay content, and annealing conditions. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers [source] Turbulent flows on forested hilly terrain: the recirculation regionTHE QUARTERLY JOURNAL OF THE ROYAL METEOROLOGICAL SOCIETY, Issue 625 2007D. Poggi Abstract A number of analytical and numerical studies employing first-order closure principles have suggested that canopy flows on gentle sinusoidal hills feature a recirculation region, situated on the lee side, that can dramatically affect scalar transfer between the biosphere and the atmosphere. To date, the onset of this region, and its effects on bulk flow properties, have not been experimentally investigated. We study the applicability of first-order closure schemes jointly with the properties of this recirculation region, using detailed laser Doppler anemometry (LDA) measurements. These experiments are conducted in a neutrally stratified boundary-layer flow within a large flume over a train of gentle and narrow hills. The canopy is composed of an array of vertical cylinders with a frontal-area index concentrated in the upper third, to resemble a tall hardwood forest at maximum leaf area. The LDA measurements are recorded for both sparse and dense canopies. We find that, while the onset of a recirculation region is ambiguous in the sparse-canopy case, it is well delineated in the dense-canopy case. This finding constitutes the first experimental evidence confirming the analytical and numerical model predictions concerning this region in dense canopies on gentle hills. Moreover, we show that the presence of the recirculation region can explain the anomalous pressure variation across the hill (first reported in numerical simulations) using an ,effective hill shape' function. Detailed momentum-flux measurements show, surprisingly, that the effective mixing length leff within the canopy and in the inner layer is not significantly affected by the recirculation region. We expected leff to be comparable to the size of the vortex responsible for the recirculation zone, but the measurements show that leff maintains its canonical canopy turbulence shape. Using laser-induced fluorescence (LIF) measurements, we find that the recirculation region is not characterized by a classical ,rotor', but by a highly intermittent zone with alternating positive and negative velocity values in the lower layers of the canopy. These LIF measurements may explain why leff maintains its canonical canopy turbulence shape in the recirculation region. The LIF measurements also show that the main mechanism for scalar transfer within the recirculation region is a sequence of accumulation,ejection episodes that are quasi-periodic in nature. Copyright © 2007 Royal Meteorological Society [source] Macular blood flow measured by blue-field entoptoscopy and Heidelberg retinal flowmetry: comparison of two techniques in type 1 diabetes women during pregnancyACTA OPHTHALMOLOGICA, Issue 5 2009Sirpa Loukovaara Abstract. Purpose:, This study compared macular capillary leucocyte velocity values measured with a psychophysical blue-field entoptic simulation (BFS) technique and confocal scanning laser Doppler flowmetry. Methods:, A cross-sectional study was performed where macular capillary leucocyte velocity was measured by BFS using an Oculix BFS-2000 V2.1 psychophysical system and by confocal scanning laser Doppler flowmetry using Heidelberg retinal flowmetry (HRF) in 35 type 1 diabetes women during the second trimester. Results:, The macular leucocyte velocities measured with BFS correlated significantly with the 50th percentile (r = 0.345, p = 0.042, n = 35, Spearman's non-parametric correlation), the 75th percentile (r = 0.432, p = 0.009) and the 90th percentile (r = 0.373, p = 0.027) of HRF flow values during the second trimester. However, there was no correlation between BFS velocity and the 25th percentile of HRF measurements. Conclusions:, Blue-field simulation is known to be an experimental technique that provides a quantitative measure of flow in the perifoveal capillary network. By contrast, HRF imaging reflects quantitative, multispectral, objective and non-invasive measurements in a two-dimensional projection of a three-dimensional retinal capillary bed. Our study showed that BFS velocity was correlated with HRF values in a group of women with diabetes during pregnancy. The positive correlation between BFS and HRF values suggests that the psychophysical BFS and scanning laser-based HRF measure similar functions in the retina. [source] Pseudoexfoliatio capsulae and endothelin-1 plasma levelsACTA OPHTHALMOLOGICA, Issue S232 2000G. L. Possati M. Cellini Summary The authors found an increase of endothelin-1 (ET-1) plasma levels in patients with pseudoexfoliatio syndrome (PXS): 2.730±0.224 pg/ml vs 1.420±0.30S pg/ml. With Color Doppler Imaging (CDI) they found in PXS patients a decrease of peak systolic velocity values in the posterior ciliary arteries that were 12.725 ± 2.536 cm/sec vs 15.450 ± 3.173 cm/sec (p<0.049) while the resistance values were increased 0.640 ± 0.051 vs 0.548 ± 0.058 (p<0.001). The increase of ET-1 plasma levels may assess the vasospasm and uveal tissue hypoxia. [source] | |||||||||||||||||||