Home About us Contact
|
Home About us Contact | ||
|
|
||
Ultrasonic Spray Pyrolysis (ultrasonic + spray_pyrolysi)
Selected AbstractsHigh-Performance Carbon-LiMnPO4 Nanocomposite Cathode for Lithium BatteriesADVANCED FUNCTIONAL MATERIALS, Issue 19 2010Seung-Min Oh Abstract A cathode material of an electrically conducting carbon-LiMnPO4 nanocomposite is synthesized by ultrasonic spray pyrolysis followed by ball milling. The effect of the carbon content on the physicochemical and electrochemical properties of this material is extensively studied. A LiMnPO4 electrode with 30 wt% acetylene black (AB) carbon exhibits an excellent rate capability and good cycle life in cell tests at 55 and 25 °C. This electrode delivers a discharge capacity of 158 mAh g,1 at 1/20 C, 126 mAh g,1 at 1 C, and 107 mAh g,1 at 2 C rate, which are the highest capacities reported so far for this type of electrode. Transmission electron microscopy and Mn dissolution results confirm that the carbon particles surrounding the LiMnPO4 protect the electrode from HF attack, and thus lead to a reduction of the Mn dissolution that usually occurs with this electrode. The improved electrochemical properties of the C-LiMnPO4 electrode are also verified by electrochemical impedance spectroscopy. [source] Synthesis and Characterization of Nanostructured Cerium Dioxide Thin Films Deposited by Ultrasonic Spray PyrolysisJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 1 2010Mario F. García-Sánchez Nanostructured thin films of cerium dioxide have been prepared on single-crystalline silicon substrates by ultrasonic spray pyrolysis using cerium acetylacetonate as a metal,organic precursor dissolved in anhydrous methanol and acetic acid as an additive. The morphology, structure, optical index, and electrical properties were studied by X-ray diffraction, scanning electron microscopy, atomic force microscopy, ellipsometry, and impedance spectroscopy. The use of additives is very important to obtain crack-free films. The substrate temperature and flow rate was optimized for obtaining smooth (Ra<0.4 nm), dense (n>2), and homogeneous nanocrystalline films with grain sizes as small as 10 nm. The influence of thermal annealing on the structural properties of films was studied. The low activation energy calculated for total conductivity (0.133 eV) is attributed to the nanometric size of the grains. [source] Structure of Disodium Dimolybdate Synthesized Using Thermodynamically Stable Molybdenum (VI) Oxide Clusters as PrecursorsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 10 2009Dragana J. Jovanovi The structure of disodium dimolybdate (Na2Mo2O7) synthesized by a low-temperature method in the process of ultrasonic spray pyrolysis using acidified aqueous solutions of thermodynamically stable molybdenum (VI) oxide clusters as a precursor was refined down to an R -factor of 7%. The refinement of the diffraction data showed that Na2Mo2O7 powder synthesized at 300°C belongs to the base-centered orthorhombic type of structure with a space group of Cmca (no. 64). It was found that the basic units of the octahedral MoO6 precursor complexes exist in the structure of Na2Mo2O7. Tetrahedral MoO4 building units that coexist together with octahedral units in the structure of Na2Mo2O7 are most likely developed by the termination of weak octahedral bonds and by the placement of the molybdenum atom in the center of the tetrahedra. [source] Spray Pyrolysis of Fe3O4,BaTiO3 Composite ParticlesJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 2009Tomoyuki Adachi Fe3O4,BaTiO3 composite particles were successfully prepared by ultrasonic spray pyrolysis. A mixture of iron(III) nitrate, barium acetate and titanium tetrachloride aqueous solution were atomized into the mist, and the mist was dried and pyrolyzed in N2 (90%) and H2 (10%) atmosphere. Fe3O4,BaTiO3 composite particle was obtained between 900° and 950°C while the coexistence of FeO was detected at 1000°C. Transmission electron microscope observation revealed that the composite particle is consisted of nanocrystalline having primary particle size of 35 nm. Lattice parameter of the Fe3O4,BaTiO3 nanocomposite particle was 0.8404 nm that is larger than that of pure Fe3O4. Coercivity of the nanocomposite particle (390 Oe) was much larger than that of pure Fe3O4 (140 Oe). These results suggest that slight diffusion of Ba into Fe3O4 occurred. [source] | ||||||||||