Home  About us  Contact
 

Toughness Values (toughness + value)

Distribution by Scientific Domains
Polymers and Materials Science80%

Kinds of Toughness Values

  • fracture toughness value
    		•

    Selected Abstracts

    Comparison of polyamide 66,organoclay binary and ternary nanocomposites

    ADVANCES IN POLYMER TECHNOLOGY, Issue 3 2009
    Miray Mert
    Abstract Polyamide 66,Lotader® 2210 blends (95/5 w/w), polyamide 66,Cloisite® 15A binary nanocomposites (98/2 w/w), and polyamide 66,Lotader® 2210,Cloisite® 15A ternary nanocomposites (93/5/2 w/w) were prepared by twin-screw extrusion, and the changes in mechanical properties, morphology, and flow properties of the materials prepared by different mixing sequences were investigated in this study. Lotader® 2210, which is a random terpolymer of ethylene, butyl acrylate, and maleic anhydride, was used as the impact modifier for polyamide 66 blends as well as polyamide 66 based nanocomposites. The best dispersion level, highest mechanical properties, highest viscosity values, and smallest elastomeric domain sizes were obtained for the mixing sequence in which all the components forming the ternary nanocomposites were compounded simultaneously. Incorporation sequence of either the organoclay or the impact modifier into the polymeric matrix was varied in the other mixing sequences, and this resulted in poorer distribution of the organoclay platelets and elastomeric domains in the matrix owing to insufficient shear intensity applied on the components in a single extrusion step. Toughness values of the ternary nanocomposites were improved compared with the binary nanocomposites upon addition of the impact modifier into polymer,organoclay combination. It was concluded that the compounding sequence of the components plays a significant role in the dispersion of organoclay and the properties of the nanocomposites, because it directly affects the interaction between the different phases. © 2009 Wiley Periodicals, Inc. Adv Polym Techn 28:155,164, 2009; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.20158 [source]

    Experimental and numerical studies on dynamic crack growth in layered slate rock under wedge impact loads: part II , non-plane strain problem

    FATIGUE & FRACTURE OF ENGINEERING MATERIALS AND STRUCTURES, Issue 10 2007
    M. R. ALAM
    ABSTRACT Dynamic crack propagation in non-plane strain (or 3D) slate blocks under wedge impact loads was investigated numerically in this part of the paper. A parabolic-shaped crack trajectory was taken into consideration to model the crack propagation in slate blocks for analyzing the impact splitting of layered slate rock. Major and minor axes of the parabola were determined from the condition of equal mode I stress intensity factors (SIFs) along the crack front. Mode I SIFs were determined for experimental breaking loads for each increment of crack growth in a manner similar to that mentioned in part I of this paper. These values were compared with the plane strain material fracture toughness value obtained from experimental studies and very good agreement was obtained between them, for the case of actual load applied on the specimen. Numerical analysis of a field problem, i.e., separation of a large-sized slate slab from the rock strata in a slate quarry using wedge impacting, was also carried out in this paper. It can be observed that a large magnitude of load is required to break large-sized slate blocks; but this load is applied through a number of smaller load-capacity actuators-in-parallel, requiring large power capacity for the hydraulic pumps. However, this required power could be reduced considerably if the load applied on the line of hydraulic actuators is cascaded across the (line of) actuators (starting from centrally placed actuators) with a small time delay (equal to the initial crushing time in slate rock). [source]

    Modelling ductile fracture behaviour from deformation parameters in HSLA steels

    FATIGUE & FRACTURE OF ENGINEERING MATERIALS AND STRUCTURES, Issue 10 2004
    S. SIVAPRASAD
    ABSTRACT In this work, an attempt is made to model the ductile fracture behaviour of two Cu-strengthened high strength low alloy (HSLA) steels through the understanding of their deformation behaviour. The variations in deformation behaviour are imparted by prior deformation of steels to various predetermined strains. The variations in parameters such as yield strength and true uniform elongation with prior deformation is studied and was found to be analogous to that of initiation fracture toughness determined by independent method. A unique method is used to measure the crack tip deformation characterized by stretch zone depth that also depicted a similar trend. Fracture toughness values derived from the stretch zone depth measurements were found to vary in the same fashion as the experimental values. A semiempirical relationship for obtaining ductile fracture toughness from basic deformation parameters is derived and model is demonstrated to estimate initiation ductile fracture toughness accurately. [source]

    Spark Plasma Sintering of Alumina

    JOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 8 2002
    Zhijian Shen
    A systematic study of various spark plasma sintering (SPS) parameters, namely temperature, holding time, heating rate, pressure, and pulse sequence, was conducted to investigate their effect on the densification, grain-growth kinetics, hardness, and fracture toughness of a commercially available submicrometer-sized Al2O3 powder. The obtained experimental data clearly show that the SPS process enhances both densification and grain growth. Thus, Al2O3 could be fully densified at a much lower temperature (1150°C), within a much shorter time (minutes), than in more conventional sintering processes. It is suggested that the densification is enhanced in the initial part of the sintering cycle by a local spark-discharge process in the vicinity of contacting particles, and that both grain-boundary diffusion and grain-boundary migration are enhanced by the electrical field originating from the pulsed direct current used for heating the sample. Both the diffusion and the migration that promote the grain growth were found to be strongly dependent on temperature, implying that it is possible to retain the original fine-grained structure in fully densified bodies by avoiding a too high sintering temperature. Hardness values in the range 21,22 GPa and fracture toughness values of 3.5 ± 0.5 MPa·m1/2 were found for the compacts containing submicrometer-sized Al2O3 grains. [source]

    Cyclic Fatigue-Crack Growth and Fracture Properties in Ti3SiC2 Ceramics at Elevated Temperatures

    JOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 12 2001
    Da Chen
    The cyclic fatigue and fracture toughness behavior of reactive hot-pressed Ti3SiC2 ceramics was examined at temperatures from ambient to 1200°C with the objective of characterizing the high-temperature mechanisms controlling crack growth. Comparisons were made of two monolithic Ti3SiC2 materials with fine- (3,10 ,m) and coarse-grained (70,300 ,m) microstructures. Results indicate that fracture toughness values, derived from rising resistance-curve behavior, were significantly higher in the coarser-grained microstructure at both low and high temperatures; comparative behavior was seen under cyclic fatigue loading. In each microstructure, ,Kth fatigue thresholds were found to be essentially unchanged between 25° and 1100°C; however, there was a sharp decrease in ,Kth at 1200°C (above the plastic-to-brittle transition temperature), where significant high-temperature deformation and damage are first apparent. The substantially higher cyclic-crack growth resistance of the coarse-grained Ti3SiC2 microstructure was associated with extensive crack bridging behind the crack tip and a consequent tortuous crack path. The crack-tip shielding was found to result from both the bridging of entire grains and from deformation kinking and bridging of microlamellae within grains, the latter forming by delamination along the basal planes. [source]