Home About us Contact
|
Home About us Contact | ||
|
|
||
TiAl Alloys (tial + alloy)
Selected AbstractsNano-Scale Design of TiAl Alloys Based on ,-Phase Decomposition,ADVANCED ENGINEERING MATERIALS, Issue 5 2006F. Appel Abstract Phase decomposition and ordering reactions in ,/B2-phase containing TiAl alloys were utilized to establish a novel, previously unreported, type of laminate microstructure. The characteristic constituent of this microstructure are laths with a nanometer-scale substructure that are comprised of several stable and metastable phases. Microstructural control can be achieved by conventional thermomechanical processing and leads to a structurally and chemically very homogeneous material with excellent mechanical properties. The physical metallurgy of this novel type of alloy has been assessed by transmission electron microscope investigations and mechanical testing. [source] Microstructural Characterization of Lamellar Features in TiAl by FIB Imaging,ADVANCED ENGINEERING MATERIALS, Issue 6 2010Dennis Peter A novel experimental procedure is introduced to determine phase fractions and the distribution of individual phases of TiAl-based two-phase alloys using the focused ion beam (FIB) technique. Two , -titanium aluminide alloys with a fine-grained duplex and a nearly lamellar microstructure are examined. The special FIB-based preparation procedure results in high contrast ion beam-induced images for all investigated alloys and allows to quantify the phase contents easily by automated microstructural analysis. Fine two-phase structures, e.g. lamellar colonies in , -TiAl, can be imaged in high resolution with respect to different phases. To validate the FIB-derived data, we compare them to results obtained with another method to determine phase fractions, electron back-scatter diffraction (EBSD). This direct comparison shows that the FIB-based technique generally provides slightly higher ,2 -fractions, and thus helps to overcome the limited lateral resolution near grain boundaries and interfaces associated with the conventional EBSD approach. Our study demonstrates that the FIB-based technique is a simple, fast, and more exact way to determine high resolution microstructural characteristics with respect to different phase constitutions in two-phase TiAl alloys and other such materials with fine, lamellar microstructures. [source] Nano-Scale Design of TiAl Alloys Based on ,-Phase Decomposition,ADVANCED ENGINEERING MATERIALS, Issue 5 2006F. Appel Abstract Phase decomposition and ordering reactions in ,/B2-phase containing TiAl alloys were utilized to establish a novel, previously unreported, type of laminate microstructure. The characteristic constituent of this microstructure are laths with a nanometer-scale substructure that are comprised of several stable and metastable phases. Microstructural control can be achieved by conventional thermomechanical processing and leads to a structurally and chemically very homogeneous material with excellent mechanical properties. The physical metallurgy of this novel type of alloy has been assessed by transmission electron microscope investigations and mechanical testing. [source] Investigation on the oxidation behaviour of gamma titanium aluminides coated with thermal barrier coatingsMATERIALS AND CORROSION/WERKSTOFFE UND KORROSION, Issue 7 2008R. Braun Abstract In the present study, the applicability of thermal barrier coatings (TBCs) on ,-TiAl alloys was investigated. Two alloys with the chemical compositions of Ti-45Al-8Nb-0.2B-0.15C and Ti-45Al-1Cr-6Nb-0.4W-0.2B-0.5C-0.2Si were used. Before TBC deposition, the specimens were pre-oxidised in laboratory air or low partial pressure oxygen atmosphere. Yttria partially stabilised zirconia top coats were then deposited using electron-beam physical vapour deposition (EB-PVD). The oxidation behaviour of the ,-TiAl specimens with TBC was studied by cyclic oxidation testing in air at 850 and 900,°C. Post-oxidation analysis of the coating systems was performed using scanning electron microscopy with energy-dispersive X-ray spectroscopy (EDS). No spallation of the TBC was observed for pre-oxidised specimens of both alloys when exposed to air at 850,°C for 1100 cycles of 1,h dwell time at high temperature. SEM micrographs of the thermally grown oxide scale revealed outer mixed TiO2/Al2O3 protrusions with a columnar structure. The protrusions contained small particles of zirconia and a low amount of about 0.5 at% zirconium was measured by EDS analysis throughout this outer oxide mixture. The TBCs exhibited excellent adherence on the oxide scale. Intercolumnar gaps and pores in the root area of the TBC were filled with titania and alumina. Below the outer columnar oxide scale, a broad porous zone of predominant titania was observed. The transition region between the oxide scale and substrate consisted of a discontinuous nitride layer intermixed with alumina particles and intermetallic phases rich in niobium formed at the nitride layer/substrate interface. When thermally cycled at 900,°C, the oxide scales on the alloy Ti-45Al-8Nb-0.2B-0.15C pre-oxidised in low partial pressure oxygen spalled off after 540 cycles. For the sample with TBC, spallation was observed after 810 cycles. Failure occurred in the thermally grown oxide near the oxide/nitride layer interface. Microstructural examinations revealed again oxide scales with columnar structure beneath the zirconia top coat and good adherence of the TBC on the thermally grown oxides formed at 900,°C. [source] | ||||||||||