Home About us Contact
|
Home About us Contact | ||
|
|
||
Testing System (testing + system)
Selected AbstractsPreparation and properties of polyurethane/montmorillonite nanocomposites cured under room temperaturePOLYMER COMPOSITES, Issue 5 2006Hangbin Jiang The polyurethane/C16C18 -MMT (the montmorillonite modified with cetyloctadecyldimethyl ammonium bromide) nanocomposites were synthesized by intercalative polymerization and cured under room temperature. The d -spacing and the dispersion of the C16C18 -MMT in the nanocomposites were measured by X-ray Diffraction (XRD) and Transmission Electron Microscope (TEM). The mechanical and thermal properties of the nanocomposites were measured by Universal Testing System, Electric Anti-fold Instrument, Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC). It was found out that introducing C16C18 -montmorillonite (MMT) in the polyurethane (PU) displayed good mechanical properties and thermal stability. Rheology behavior in liquid state showed that the addition of the C16C18 -MMT to PU resulted in low gel time and high viscosity. POLYM. COMPOS. 27:470,474, 2006. © 2006 Society of Plastics Engineers. [source] Biomechanical Strength of Human Nasal Septal Lining: Comparison of the Constituent LayersTHE LARYNGOSCOPE, Issue 8 2005David W. Kim MD Abstract Objective/Hypothesis: Nasal septal perforation is a common complication following surgery involving the nasal septum. Septoplasty, septorhinoplasty, and submucosal resection may result in the inadvertent resection of perichondrium, which may predispose the patient to septal perforations. Study Design: Controlled human cadaver study testing the biomechanical strength of the constituent layers of nasal septal lining. Methods: Uniform samples of nasal septal mucosa, perichondrium, and a composite of both layers were obtained from five fresh human cadavers. The mechanical tensile strength of these layers was evaluated and compared with the Instron 4301 Mechanical Testing System (Canton, MA). Results: Mixed-effects regression analysis demonstrated a significant difference in the tensile strength of the three groups (mean values ± SD: mucosa, 662 ± 308 g; perichondrium, 1370 ± 798 g; composite, 2340 ± 1252 g). All three pairwise comparisons among the three groups showed a significant difference in tensile strength. Conclusion: The perichondrial layer imparts the majority of the biomechanical strength to septal lining. Lining flaps containing both perichondrium and mucosa are stronger than flaps with either perichondrium or mucosa alone. Dissection in the subperichondrial plane during septal surgery provides a stronger septal flap and may prevent the development of nasal septal perforation during nasal surgery. [source] Exploring the role of face processing in facial emotion recognition in schizophreniaACTA NEUROPSYCHIATRICA, Issue 6 2009Paola Rocca Objective: Impairment in emotion perception represents a fundamental feature of schizophrenia with important consequences in social functioning. A fundamental unresolved issue is the relationship between emotion perception and face perception. The aim of the present study was to examine whether facial identity recognition (Identity Discrimination) is a factor predicting facial emotion recognition in the context of the other factors, known as contributing to emotion perception, such as cognitive functions and symptoms. Methods: We enrolled 58 stable schizophrenic out-patients and 47 healthy subjects. Facial identity recognition and emotion perception were assessed with the Comprehensive Affect Testing System. Different multiple regression models with backward elimination were performed in order to discover the relation of each significant variable with emotion perception. Results: In a regression including the six significant variables (age, positive symptomatology, Identity Discrimination, attentive functions, verbal memory-learning, executive functions) versus emotion processing, only attentive functions (standardised , = 0.264, p = 0.038) and Identity Discrimination (standardised , = 0.279, p = 0.029) reached a significant level. Two partial regressions were performed including five variables, one excluding attentive functions and the other excluding Identity Discrimination. When we excluded attentive functions, the only significant variable was Identity Discrimination (standardised , = 0.278, p = 0.032). When we excluded Identity Discrimination, both verbal memory-learning (standardised , = 0.261, p = 0.042) and executive functions (standardised , = 0.253, p = 0.048) were significant. Conclusions: Our results emphasised the role of face perception and attentional abilities on affect perception in schizophrenia. We additionally found a role of verbal memory-learning and executive functions on emotion perception. The relationship between those above-mentioned variables and emotion processing could have implications for cognitive rehabilitation. [source] Human exposure to endocrine disrupters: Standardisation of a marker of estrogenic exposure in adipose tissue,APMIS, Issue 3 2001Ana Rivas In many epidemiological studies based on the direct measurement of exposure to organochlorines, the chemicals of concern are determined directly from adipose tissue samples. Although the measurement of all possible organochlorines, their metabolites, isomers and congeners may be desirable, it is expensive and time-consuming and many chemicals with hormonal activity may not yet have been identified. Testing systems are therefore required to screen for estrogenicity and to identify appropriate biomarkers of human exposure. To address this issue, we developed and standardised a method to assess the total estrogenic xenobiotic burden in human adipose tissue. The method extracts and separates the more lipophilic xenoestrogens from ovarian estrogens, with a subsequent bioassay determination of the cumulative effect of the xenoestrogens. It was applied to 400 women, using 200 mg of adipose tissue: 65% of samples showed measurable estrogenicity in the fraction where most non-polar xenoestrogens eluted, and 76% of fractions where ovarian estrogens eluted were positive for estrogenicity. Residues of 16 organochlorine pesticides were determined. No correlation was found between pesticide content and estrogenicity of the samples. The high percentage of positive samples suggests that the method is sensitive enough to be used as a biomarker of human exposure to estrogenic xenobiotics and can be applied in epidemiological studies. [source] Validation and Clinical Utility of a Simple In-Home Testing Tool for Sleep-Disordered Breathing and Arrhythmias in Heart Failure: Results of the Sleep Events, Arrhythmias, and Respiratory Analysis in Congestive Heart Failure (SEARCH) StudyCONGESTIVE HEART FAILURE, Issue 5 2006William T. Abraham MD Fifty patients with New York Heart Association class III systolic heart failure were enrolled in this prospective multicenter study that compared the diagnostic accuracy of a home-based cardiorespiratory testing system with standard attended polysomnography. Patients underwent at least 2 nights of evaluation and were scored by blinded observers. At diagnostic cutoff points of ,5, ,10, and ,15 events per hour for respiratory disturbance severity, polysomnography demonstrated a sleep-disordered breathing prevalence of 69%, 59%, and 49%, respectively. Compared with polysomnography, the cardiorespiratory testing system demonstrated predictive accuracies of 73%, 73%, and 75%, which improved to 87%, 87%, and 83%, respectively, when analysis of covariance suggested reanalysis omitting one site's data. The system accurately identified both suspected and unsuspected arrhythmias. The device was judged by 80% of patients to be easy or very easy to use, and 74% of patients expressed a preference for the in-home system. Therefore, this system represents a reasonable home testing device in these patients. [source] Stability analysis for real-time pseudodynamic and hybrid pseudodynamic testing with multiple sources of delayEARTHQUAKE ENGINEERING AND STRUCTURAL DYNAMICS, Issue 10 2008Oya Mercan Abstract Real-time pseudodynamic (PSD) and hybrid PSD test methods are experimental techniques to obtain the response of structures, where restoring force feedback is used by an integration algorithm to generate command displacements. Time delays in the restoring force feedback from the physical test structure and/or the analytical substructure cause inaccuracies and can potentially destabilize the system. In this paper a method for investigating the stability of structural systems involved in real-time PSD and hybrid PSD tests with multiple sources of delay is presented. The method involves the use of the pseudodelay technique to perform an exact mapping of fixed delay terms to determine the stability boundary. The approach described here is intended to be a practical one that enables the requirements for a real-time testing system to be established in terms of system parameters when multiple sources of delay exist. Several real-time testing scenarios with delay that include single degree of freedom (SDOF) and multi-degree of freedom (MDOF) real-time PSD/hybrid PSD tests are analyzed to illustrate the method. From the stability analysis of the real-time hybrid testing of an SDOF test structure, delay-independent stability with respect to either experimental or analytical substructure delay is shown to exist. The conditions that the structural properties must satisfy in order for delay-independent stability to exist are derived. Real-time hybrid PSD testing of an MDOF structure equipped with a passive damper is also investigated, where observations from six different cases related to the stability plane behavior are summarized. Throughout this study, root locus plots are used to provide insight and explanation of the behavior of the stability boundaries. Copyright © 2008 John Wiley & Sons, Ltd. [source] Measurement of pressure and flow rates during irrigation of a root canal ex vivo with three endodontic needlesINTERNATIONAL ENDODONTIC JOURNAL, Issue 7 2007C. Boutsioukis Abstract Aim, To monitor ex vivo intra-canal irrigation with three endodontic needles (25, 27 and 30 gauge) and compare them in terms of irrigant flow rate, intra-barrel pressure, duration of irrigation and volume of irrigant delivered. Methodology, A testing system was constructed to allow measurement of selected variables with pressure and displacement transducers during ex vivo intra-canal irrigation with a syringe and three different needles (groups A, B, C) into a prepared root canal. Ten specialist endodontists performed the irrigation procedure. Each operator performed ten procedures with each needle. Data recorded by the transducers were analysed using Friedman's test, Wilcoxon Signed Rank test, Mann,Whitney U -test and Kendall's Tb test. The level of significance was set to 95%. Results, Significant differences were detected among the three needles for most variables. Duration of delivery and flow rates significantly decreased as the needle diameter increased, whilst pressure increased up to 400,550 kPa. Gender of the operator had a significant impact on the results. Experience of the operators (years) were negatively correlated to volume of irrigant (all groups), to the duration of delivery (groups A, B) and to the average flow rate (group A). Conclusions, Finer diameter needles require increased effort to deliver the irrigant and result in higher intra-barrel pressure. The syringe and needles used tolerated the pressure developed. Irrigant flow rate should be considered as a factor directly influencing flow beyond the needle. Wide variations of flow rate were observed among operators. Syringe irrigation appears difficult to standardize and control. [source] Intensification of liquid,liquid two-phase mass transfer by gas agitation in a microchannelAICHE JOURNAL, Issue 8 2009Yuanhai Su Abstract In this experiment, the inert gas is used to agitate two immiscible fluids in microchannels. The mass transfer performances with or without gas agitation are investigated. 30% TBP (in kerosene)-acetic acid-water is chosen as testing system, and nitrogen as agitating gas. The superficial velocities of the immiscible liquid,liquid two phases and gas phase are varied in the range from 0.02 to 1.2 m/s, and 0 to 3.0 m/s, respectively. In microchannels, with enough gas agitating intensity, high dispersion between two immiscible liquid phases can be obtained. The overall volumetric mean mass transfer coefficients are two-folds higher than those without gas agitating, which are in the range of 3.8,30.6 s,1. Some parameters which impact on the mass transfer process, such as the mixture superficial velocity of the immiscible liquid,liquid two phases, the gas superficial velocity, the microchannel structure, the gas inlet locations and the sampling time are experimentally investigated. © 2009 American Institute of Chemical Engineers AIChE J, 2009 [source] Joint degeneration following closed intraarticular fracture in the mouse knee: A model of posttraumatic arthritisJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 5 2007Bridgette D. Furman Abstract Posttraumatic arthritis is one of the most frequent causes of disability following joint trauma. The objective of this study was to develop a model of a closed articular fracture in the mouse knee joint to quantify the temporal sequence of joint degeneration in a model of posttraumatic arthritis. Closed intraarticular fractures were created in the tibial plateau of adult mice (C57BL/6) using a computer-controlled materials testing system and a custom-built indenter tip. Tibial plateau fractures were classified and imaged over time using high-resolution digital radiography. Animals were sacrificed at 2, 4, 8, and 50 weeks following fracture, and the experimental and contralateral control limbs were harvested for histology and micro-computed tomography (microCT) analysis. By radiographic analysis, tibial plateau fractures closely resembled clinical fractures. More complex and comminuted fractures correlated to significantly higher fracture energies. Histologic analysis demonstrated progressive joint degeneration as measured by a modified Mankin scale, with fibrillation and loss of proteoglycan in the articular cartilage. Subchondral bone thickening was also observed in experimental joints. The induction of a closed intraarticular fracture of the mouse tibial plateau generated a reproducible and clinically relevant joint injury that progressed to osteoarthritis-like changes by histologic and microCT evaluations. The ability to induce joint degeneration without an osteotomy or open arthrotomy provides a valuable new model for studying the natural sequelae of posttraumatic arthritis. Notably, the use of a murine model will facilitate the use of genetically modified animals for the investigation of specific genes implicated in the pathology of posttraumatic arthritis. © 2007 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 25:578,592, 2007 [source] Knee biomechanics after UKA and its relation to the ACL,a robotic investigationJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 4 2006Jeremy F. Suggs Abstract Unicompartmental knee arthroplasty (UKA) has regained popularity in recent years. However, limited data exist on how UKA affects knee biomechanics. The role of the anterior cruciate ligament (ACL) after fixed bearing UKA remains controversial. In this study, a robotic testing system was used to apply a quadriceps/hamstrings load to cadaveric knee specimens in the intact state, after medial UKA, and after transection of the ACL in UKA. The load was applied to the knee from full extension to 120° of flexion in 30° increments. UKA generally did not affect anterior,posterior (AP) femoral position, but did cause external tibial rotation and variations in varus,valgus rotation compared to the intact knee. ACL transection after UKA shifted the femur posteriorly compared to the intact and UKA knees and increased internal tibial rotation compared to the UKA knee at low flexion. The AP motion of the articular contact position in the implant was increased after ACL transection. These data might help explain the mechanism of tibial component loosening and provide insight into further investigations of polyethylene wear in UKA. Based on the kinematic data, the ACL should be functional to provide patients the greatest opportunity for long-term success after medial UKA. © 2006 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res [source] Distribution of in situ forces in the anterior cruciate ligament in response to rotatory loadsJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 1 2004Mary T. Gabriel Abstract The anterior cruciate ligament (ACL) can be anatomically divided into anteromedial (AM) and posterolateral (PL) bundles. Current ACL reconstruction techniques focus primarily on reproducing the AM bundle, but are insufficient in response to rotatory loads. The objective of this study was to determine the distribution of in situ force between the two bundles when the knee is subjected to anterior tibial and rotatory loads. Ten cadaveric knees (50 ± 10 years) were tested using a robotic/universal forcemoment sensor (UFS) testing system. Two external loading conditions were applied: a 134 N anterior tibial load at full knee extension and 15°, 30°, 60°, and 90° of flexion and a combined rotatory load of 10 N m valgus and 5 N m internal tibial torque at 15° and 30° of flexion. The resulting 6 degrees of freedom kinematics of the knee and the in situ forces in the ACL and its two bundles were determined. Under an anterior tibial load, the in situ force in the PL bundle was the highest at full extension (67 ± 30 N) and decreased with increasing flexion. The in situ force in the AM bundle was lower than in the PL bundle at full extension, but increased with increasing flexion, reaching a maximum (90 ± 17 N) at 60° of flexion and then decreasing at 90°. Under a combined rotatory load, the in situ force of the PL bundle was higher at 15° (21 ± 11 N) and lower at 30° of flexion (14 ± 6 N). The in situ force in the AM bundle was similar at 15° and 30° of knee flexion (30 ± 15 vs. 35 ± 16 N, respectively). Comparing these two external loading conditions demonstrated the importance of the PL bundle, especially when the knee is near full extension. These findings provide a better understanding of the function of the two bundles of the ACL and could serve as a basis for future considerations of surgical reconstruction in the replacement of the ACL. © 2003 Orthopaedic Research Society. Published by Elsevier Ltd. All rights reserved. [source] Joint compression alters the kinematics and loading patterns of the intact and capsule-transected AC jointJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 3 2003Ryan S. Costic High compressive loads are transmitted through the shoulder across the acromioclavicular (AC) joint to the axial skeleton during activities of daily living and can lead to early joint degeneration or instability. The objective of this study was to quantify the effect of joint compression on the biomechanics of the intact and capsule-transected AC joint during application of three loading conditions. A robotic/universal force-moment sensor testing system was utilized to apply an anterior, posterior or superior load of 70 N in combination with 10 or 70 N of joint compression to fresh-frozen cadaveric shoulders (n = 12). The application of joint compression to the intact AC joint decreased the posterior translation in response to a posterior load (,6.6 ± 2.5 vs ,3.7 ± 1.0 mm, p<0.05). Joint compression also decreased the in situ force in the superior AC capsule by 10 N while increasing the joint contact force by 20 N for all loading conditions (p<0.05). The application of joint compression to the capsule-transected AC joint significantly decreased the amount of posterior and superior translation during posterior (,12.7 ± 6.1 vs ,5.5 ± 3.2 mm, p < 0.05) and superior (5.3 ± 2.9 vs 4.2 ± 2.3 mm, p < 0.05) loading, respectively, while significantly increasing the coupled translations (anterior,posterior, superior,inferior or proximal,distal) in all loading conditions (p < 0.05). The joint contact force also significantly increased by 20 N for all loading conditions (p < 0.05). This quantitative data suggests: (1) common surgical techniques such as distal clavicle resection, which initially reduce painful joint contact, may cause unusually high loads to be supported by the soft tissue structures at the AC joint; and (2) compressive loads transmitted across a capsule-transected AC joint could be concentrated over a smaller area due to the increased coupled motion and joint contact force. © 2002 Orthopaedic Research Society. Published by Elsevier Science Ltd. All rights reserved. [source] Structure,activity relationship study of alkynyl ether insecticide synergists and the development of MB-599 (verbutin),PEST MANAGEMENT SCIENCE (FORMERLY: PESTICIDE SCIENCE), Issue 4 2003Béla Bertók Abstract Structure,activity relationships of aryl alkynyl synergists of the general formula of Ar,Q,R, where Q represents a bridging structure, were studied using a standardised testing system and Relative Potency values. Ethers, esters, oxime ethers, amides and amines were prepared and evaluated. The length of the R-alkynyl chain, the role of the bridge and the substitution of the aromatic ring were examined systematically. The most potent compounds possessed an aromatic ring connected via a bridge of three atoms to an alkynyl chain, forming together a linear side-chain of six atoms. Several highly potent compounds were synthesised of which one (MB-599; proposed common name verbutin) was selected for development as a selective insecticide synergist in crop protection. Its high potential at practical insecticide:synergist ratios makes possible the reduction of the total amount of insect-control chemicals applied, and its use as an additive to produce new formulations of existing insecticides makes it highly advantageous in resistance management, giving a new tool to sustain the effectiveness of a wide range of insecticides. A product containing a (1,+,1) mixture of verbutin and beta-cypermethrin was launched in Hungary in 2002. © 2003 Society of Chemical Industry [source] Performance of shark teeth during puncture and draw: implications for the mechanics of cuttingBIOLOGICAL JOURNAL OF THE LINNEAN SOCIETY, Issue 2 2010LISA B. WHITENACK The performance of an organism's feeding apparatus has obvious implications for its fitness and survival. However, the majority of studies that focus on chondrichthyan feeding have largely ignored the role of teeth. Studying the functional morphology of shark teeth not only elucidates the biological role that teeth play in feeding, but also provides insight specifically into the evolution of shark feeding because teeth are often the only structures available in the fossil record. In the present study, we investigate the puncture and draw performance of three general categories of extant teeth, tearing-type, cutting-type, and cutting,clutching type, as well as three fossil morphologies, utilizing a universal testing system. Differences in puncturing performance occurred among different prey items, indicating that not all ,soft' prey items are alike. The majority of teeth were able to puncture different prey items, and differences in puncture performance also occurred among tooth types; however, few patterns emerged. In some cases, broader triangular teeth were less effective at puncturing than narrow-cusped teeth. There were no differences between the maximum draw forces and maximum puncture forces. Many of the shark teeth in the present study were not only able to perform draw and puncture equally well, but also many tooth morphologies were functionally equivalent to each other. The findings obtained in the present study lend little support to the belief that shark tooth morphology is a good predictor of biological role. © 2010 The Linnean Society of London, Biological Journal of the Linnean Society, 2010, 100, 271,286. [source] Higher retention after a new take-home computerised testBRITISH JOURNAL OF EDUCATIONAL TECHNOLOGY, Issue 3 2008Jooyong Park A new computerised testing system was used at home to promote learning and also to save classroom instruction time. The testing system combined the features of short-answer and multiple-choice formats. The questions of the multiple-choice problems were presented without the options so that students had to generate answers for themselves; they could click for the options when they were ready, and could choose one of the options within a brief, specified time period. One hundred thirty-eight Korean sixth-grade students (12-year olds) were divided into two groups: the experimental group took the intervening test on social studies using the new computerised testing method, and the control group used a computerised version of the traditional multiple-choice method. A few days after the intervening computerised test, a recall posttest was given in paper-and-pencil format. The mean posttest score was greater for the experimental group than for the control group. Implications of the result are discussed. [source] Application of the Levenshtein Distance Metric for the Construction of Longitudinal Data FilesEDUCATIONAL MEASUREMENT: ISSUES AND PRACTICE, Issue 2 2010Harold C. Doran The analysis of longitudinal data in education is becoming more prevalent given the nature of testing systems constructed for No Child Left Behind Act (NCLB). However, constructing the longitudinal data files remains a significant challenge. Students move into new schools, but in many cases the unique identifiers (ID) that should remain constant for each student change. As a result, different students frequently share the same ID, and merging records for an ID that is erroneously assigned to different students clearly becomes problematic. In small data sets, quality assurance of the merge can proceed through human reviews of the data to ensure all merged records are properly joined. However, in data sets with hundreds of thousands of cases, quality assurance via human review is impossible. While the record linkage literature has many applications in other disciplines, the educational measurement literature lacks details of formal protocols that can be used for quality assurance procedures for longitudinal data files. This article presents an empirical quality assurance procedure that may be used to verify the integrity of the merges performed for longitudinal analysis. We also discuss possible extensions that would permit merges to occur even when unique identifiers are not available. [source] Comparison of 16S rRNA sequencing with conventional and commercial phenotypic techniques for identification of enterococci from the marine environmentJOURNAL OF APPLIED MICROBIOLOGY, Issue 6 2006D.F. Moore Abstract Aims:, To compare accuracy of genus and species level identification of presumptive enterococci isolates from the marine environment using conventional biochemical testing, four commercial identification systems and 16S rRNA sequence analysis. Methods and Results:, Ninety-seven environmental bacterial isolates identified as presumptive enterococci on mEI media were tested using conventional and Enterococcus genus screen biochemical tests, four commercial testing systems and 16S rRNA sequencing. Conventional and Enterococcus genus screen biochemical testing, 16S rRNA sequencing and two commercial test systems achieved an accuracy of ,94% for Enterococcus genus confirmation. Conventional biochemical testing and 16S rRNA sequencing achieved an accuracy of ,90% for species level identification. Conclusions:, For confirmation of Enterococcus genus from mEI media, conventional or genus screen biochemical testing, 16S rRNA sequencing and the four commercial systems were correct 79,100% of the time. For speciation to an accuracy of 90% or better, either conventional biochemical testing or 16S rRNA sequencing is required. Significance and Impact of the Study:, Accurate identification of presumptive environmental Enterococcus isolates to genus and species level is an integral part of laboratory quality assurance and further characterization of Enterococcus species from pollution incidents. This investigation determines the ability of six different methods to correctly identify environmental isolates. [source] | |||||||||||||||||||