Home About us Contact
|
Home About us Contact | ||
|
|
||
Temperature Values (temperature + value)
Selected AbstractsModeling of coat-hanger die under vibrational extrusionJOURNAL OF APPLIED POLYMER SCIENCE, Issue 2 2008Jin-Ping Qu Abstract The distributions of the pulsatile pressure field, the pulsatile velocity field, and the pulsatile resident time of the polymeric melt in the coat-hanger die are derived by using the pulsation of volumetric flow rate and pressure. Subsequently, formulae of the manifold radius and the slope of the manifold are deduced via volumetric flow rate pulsation. Polypropylene (PP) was employed for the experiments of the vibrational extrusion. The results indicate that the average extrusion pressure declines with frequency or amplitude decreasing; the distribution of residence time along the width of the coat-hanger die performs uniformly during the vibrational extrusion process; the theoretical extrusion pressure well agrees with the experimental pressure; the experiments of tensile test, impact test implicate that vibration improves the mechanical properties of products; differential scanning calorimetry testing demonstrates that the melting point of PP is moved to a higher temperature value, and the endothermic enthalpy and the crystallinity are improved as well when superimposing the vibrational force field. Accordingly, the model of the coat-hanger die under vibrational extrusion is well consistent with the experiments. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Atmospheric conditions associated with the exceptional fire season of 2003 in PortugalINTERNATIONAL JOURNAL OF CLIMATOLOGY, Issue 13 2006Ricardo M. Trigo Abstract The summer of 2003 was characterised by exceptional warm weather in Europe, particularly during the first two weeks of August, when a devastating sequence of large fires was observed, reaching an amount of circa 450 000 ha, the largest figure ever recorded in Portugal in modern times. They were concentrated in two relatively confined regions of Portugal and a considerable proportion of burnt area was due to fires started on the 2nd and 3rd of August. It is shown that the 850 hPa temperature values observed over Portugal for the 1st and 2nd of August 2003 were the highest recorded since 1958. Using data from synoptic stations covering the entire Portuguese territory, the event was characterised in fine detail, including the evolution of both maximum and minimum temperatures, surface relative humidity, and wind anomaly fields. The different spatial extent of maximum and minimum temperatures is analysed leading to the new all-time Portuguese records of 47.3 °C for maximum and 30.6 °C for minimum temperatures that were recorded on the 1st of August near the main area of occurrence of the largest fire. Finally, it is shown that the summer of 2003 was preceded by a wet winter followed by a very dry month of May, a precipitation anomalous regime that contributed to a climatic background that favoured the role played by the early August heatwave and the associated meteorological surface conditions. Copyright © 2006 Royal Meteorological Society [source] Low-grade fever: how to distinguish organic from non-organic formsINTERNATIONAL JOURNAL OF CLINICAL PRACTICE, Issue 3 2010M. Affronti Summary Background and aim:, Low-grade fever (LGF) is defined as a body temperature between 37.5 and 38.3 °C, which is below the classical value reported for fever of unknown origin (FUO). We attempted to characterise its epidemiology, aetiology and clinical aspects to improve the methodological approach to diagnosis. Design and Methods:, We reviewed and evaluated a survey of patients with LGF, followed as outpatients of our Department, a tertiary referral centre from 1997 to 2008. The same classifications were applied for classical FUO, and in the patients diagnosed with LGF, we also investigated for habitual hyperthermia (HH). Results:, Seventy-three patients were selected and divided into two groups: group A included 32 patients classified with organic fever and group B included 41 patients with HH. Aetiology of organic LGF was: infectious disease 59%; neoplasm 3.1%; inflammatory non-infectious disease 6.2%; miscellaneous 18.7%; undiagnosed 12.5%. Mean age was significantly higher in the organic fever than in the HH group (p < 0.02). Splenomegaly and loss of weight were significantly associated with organic fever (p < 0.05), while dizziness and general malaise were associated with HH. Lack of any pathological signs at physical examination was significantly more frequent in HH (p < 0.0001). Among the biochemical tests, white blood cells and C-reactive protein were more frequently above normal limits in group A than in group B (p < 0.05). Conclusions:, In our experience, LGF requires the same methodological diagnostic approach as FUO, because there is no relationship between body temperature values and the severity of the underlying diseases, and the aetiological spectrum is also the same. [source] Incidence and antibiotic susceptibility of bacteriocin-producing lactic acid bacteria from dairy productsINTERNATIONAL JOURNAL OF DAIRY TECHNOLOGY, Issue 4 2008MAHBOUBEH MIRHOSSEINI Screening for bacteriocin production by strains of lactic acid bacteria (LAB) from local dairy products in Iran resulted in the detection of 10 bacteriocin-producing strains. Among 105 isolated, 10 bacteriocin producers were phenotypically and genotypically identified as Enterococcus spp. The antimicrobial compounds produced by these novel strains were inactivated by trypsin, proteinase k. These bacteriocins also were active in a wide range of pH and temperature values, and inhibited not only the closely related LAB, but also Listeria monocytogenes. [source] Effect of the different rigidity of the chiral crosslinker on phase behaviors of side-chain chiral liquid crystalline elastomersJOURNAL OF APPLIED POLYMER SCIENCE, Issue 3 2008Bao-Yan Zhang Abstract In the present work, the phase behaviors of two series of side-chain liquid crystalline elastomers (PI and PII series) derived from the same nematic liquid crystalline monomer and the different rigidity of chiral bisolefinic crosslinking units have been compared and studied extensively, and the effect of the different rigidity of crosslinker on the phase behavior of elastomers has been discussed. The chemical structure of the monomers and polymers obtained were confirmed by FTIR and 1H NMR spectroscopy. The phase behaviors were investigated by differential scanning calorimetry, polarizing optical microscopy measurement, thermogravimetric analyses, and X-ray diffraction measurement. The two series of elastomers showed smectic or cholesteric phases. When the amount of different crosslinking units was less than 15 mol %, both of the elastomers displayed elasticity, reversible phase transition with wide mesophase temperature ranges, and high thermal stability. It is shown that the isotropization temperature values of PII series are higher than those of PI series, and the glass transition temperature values of PII series varied smoothly and that of PI series changed smoothly first and then abruptly with increasing the contents of crosslinkers with different rigidity. In addition, PI series showed an interesting change in LC texture near clearing point, but PII series did not. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Temporal and environmental influences on the variation in Atlantic salmon smolt migration in the Burrishoole system 1970,2000JOURNAL OF FISH BIOLOGY, Issue 6 2003C. J. Byrne The relationships between a number of environmental variables and the number of Atlantic salmon Salmo salar smolts migrating in the Burrishoole system, western Ireland, were examined over a 30 year period from 1970 to 2000. The number of Atlantic salmon smolts recorded migrating downstream decreased significantly from an annual mean of 11 579 in the 1970s to a mean of 6272 in the 1990s. The primary factor in the decline in Atlantic salmon numbers was a consistent decline in the number of returning adults from the 1970s until the mid 1990s. Timing of the smolt migrations (runs) was consistent throughout the three decades. The mean durations of the smolt runs were 102·1, 92·6 and 103·2 days for the 1970s, 1980s and 1990s respectively. Mean surface water temperatures at key points in the smolt run for the three decades were also similar. Mean water temperature values were 5·4, 5·1 and 5·3° C at the start of the smolt runs and 15·2, 14·9 and 15·3° C at the end of the smolt runs in the 1970s, 1980s and 1990s respectively. Multivariate analysis identified two groups of environmental variables which had a significant influence on the daily smolt catch. One group of variables dominated by photoperiod and temperature operated prior to the smolt run and was considered to regulate the development of smoltification. The second group of variables dominated by total light and water level operated within the smolt run and was considered to control daily smolt migration. [source] Glass Transition and Food Technology: A Critical AppraisalJOURNAL OF FOOD SCIENCE, Issue 7 2002M. Le Meste ABSTRACT: Most low water content or frozen food products are partly or fully amorphous. This review will discuss the extent to which it is possible to understand and predict their behavior during processing and storage, on the basis of glass transition temperature values (Tg) and phenomena related to glass transition. Two main conclusions are provisionally proposed. Firstly, glass transition cannot be considered as an absolute threshold for molecular mobility. Transport of water and other small molecules takes place even in the glassy state at a significant rate, resulting in effective exchange of water in multi-domains foods or sensitivity to oxidation of encapsulated materials. Texture properties (crispness) also appear to be greatly affected by sub-Tg relaxations and aging below Tg. Secondly, glass transition is only one among the various factors controlling the kinetics of evolution of products during storage and processing. For processes such as collapse, caking, crystallization, and operations like drying, extrusion, flaking, Tg data and WLF kinetics have good predictive value as regards the effects of temperature and water content. On the contrary, chemical/biochemical reactions are frequently observed at temperature below Tg, albeit at a reduced rate, and WLF kinetics may be obscured by other factors. [source] Quantitative palaeotemperature records inferred from fossil pollen and chironomid assemblages from Lake Gilltjärnen, northern central Sweden,JOURNAL OF QUATERNARY SCIENCE, Issue 8 2006Karin Antonsson Abstract Palaeotemperature reconstructions based on radiocarbon-dated fossil pollen and chironomid stratigraphies obtained from Lake Gilltjärnen provide evidence of climate changes during the last 11,000 years in the boreal zone of northern central Sweden. The records show consistent trends during the early and mid-Holocene, indicating low temperatures at 11,000,10,000,cal.,yr,BP, followed by a rising trend and a period of maximum values from about 7000 to 4000,cal.,yr,BP. At 3000,cal.,yr,BP the chironomid-inferred temperature values rise abruptly, deviating from the late-Holocene cooling trend indicated by the pollen-based reconstruction and most of the other palaeotemperature records from central Scandinavia, probably as a result of local limnological changes in Lake Gilltjärnen and its catchment. Comparison of the present results with a lake-level reconstruction from Lake Ljustjärnen, ca. 100,km southwest of Lake Gilltjärnen, shows that the low early-Holocene temperatures were associated with high lake-levels at 10,500,8500,cal.,yr,BP, whereas low lake-levels and dry conditions prevailed during the period of high temperatures at between 7500 and 5000,cal.,yr,BP, probably due to high summer evapotranspiration and lower precipitation. Copyright © 2006 John Wiley & Sons, Ltd. [source] Noninvasive temperature mapping with MRI using chemical shift water-fat separationMAGNETIC RESONANCE IN MEDICINE, Issue 5 2010Brian J. Soher Abstract Tissues containing both water and lipids, e.g., breast, confound standard MR proton reference frequency-shift methods for mapping temperatures due to the lack of temperature-induced frequency shift in lipid protons. Generalized Dixon chemical shift,based water-fat separation methods, such as GE's iterative decomposition of water and fat with echo asymmetry and least-squares estimation method, can result in complex water and fat images. Once separated, the phase change over time of the water signal can be used to map temperature. Phase change of the lipid signal can be used to correct for non-temperature-dependent phase changes, such as amplitude of static field drift. In this work, an image acquisition and postprocessing method, called water and fat thermal MRI, is demonstrated in phantoms containing 30:70, 50:50, and 70:30 water-to-fat by volume. Noninvasive heating was applied in an Off1-On-Off2 pattern over 50 min, using a miniannular phased radiofrequency array. Temperature changes were referenced to the first image acquisition. Four fiber optic temperature probes were placed inside the phantoms for temperature comparison. Region of interest (ROI) temperature values colocated with the probes showed excellent agreement (global mean ± standard deviation: ,0.09 ± 0.34°C) despite significant amplitude of static field drift during the experiments. Magn Reson Med 63:1238,1246, 2010. © 2010 Wiley-Liss, Inc. [source] Characterization of a rigid silicone resinPOLYMER COMPOSITES, Issue 1 2003M. B. Chan-Park Silicone resins have been used as binders for ceramic frit coatings and can withstand temperatures of 650°C to 1260°C. Conceptually, silicone resins can potentially be used as matrices for high temperature fiber-reinforced composites. The mechanical and thermal properties of a commercially available silicone resin, Dow Corning® 6-2230, were characterized. Neat 6-2230 resin was found to have inferior room temperature mechanical properties such as flexural, tensile and fracture properties when compared to epoxy. The room temperature flexural properties and short beam shear strength of the silicone/glass composites were also found to be lower than those of epoxy/glass composite with similar glass content. However, the silicone resin had better elevated temperature properties. At an elevated temperature of 316°C, the retentions of flexural modulus and strength were 80% and 40% respectively of room temperature values; these were superior to those of phenolic/glass. Unlike the carbon-based resins, the drop in flexural properties of the silicon/glass laminates with temperature leveled off with increase in temperature beyond 250°C. The resin weight loss at 316°C in 100 cm3/min of flowing air was small compared to other carbon-based resins such as PMR-15 and LaRC TPI. Only Avimid-N appeared comparable to Dow Corning® 6-2230. [source] Frequent monitoring of temperature: an essential requirement for site selection in bivalve aquaculture in tropical,temperate transition zonesAQUACULTURE RESEARCH, Issue 10 2006María Teresa Sicard Abstract Frequent monitoring of temperature (FMT) for over 1 year at two aquaculture sites in the western Baja California peninsula was analysed in terms of hourly, daily and monthly variability, and with this information, temperature-change indices were calculated. These data were contrasted against a long-term series from a global database (Extended Reconstruction of Sea Surface Temperature (ERSST)) to evaluate whether these could substitute for FMT. The compatibility of species requirements with the thermal conditions was evaluated by comparing the temperature frequency distributions from the two FMTs, with the optimum and lethal temperature information available on five bivalve species of aquacultural interest. We concluded that there was no correlation between ERSST and FMT because the former underestimates the amplitude of real temperature fluctuations and exhibits a different pattern of variation during the year. Therefore, FMT was needed for a correct selection of an aquaculture site for bivalves. The FMT indicated high temperature variability at both sites studied on different time scales, with the site located at lower latitude (Rancho Bueno) warmer and with a higher variability than Laguna Manuela. Contrasting these results with optimum and lethal temperature values of bivalve species, it was possible to find the ideal site, for temperature, for culturing the species, taking into account the variability associated with large-scale phenomena. [source] | |||||||||||||||||||