Home About us Contact
|
Home About us Contact | ||
|
|
||
Strain Level (strain + level)
Kinds of Strain Level Selected AbstractsThe effects of torsion and motion coupling in site response estimationEARTHQUAKE ENGINEERING AND STRUCTURAL DYNAMICS, Issue 5 2003Mohammad R. Ghayamghamian Abstract Soil amplification characteristics are investigated using data from the Chibaken-Toho-Oki earthquake and its aftershocks recorded at Chiba dense array in Japan. The frequency-dependent amplification function of soil is calculated using uphole-to-downhole spectral ratio analysis, considering the horizontal components of shear wave. The identified spectral ratios consistently demonstrate the splitting of peaks in their resonance frequencies and low amplification values in comparison with a 1D model. The torsional behaviour and horizontal ground motion coupling are clarified as the reasons for these phenomena at the site. To prove the hypothesis, the torsional motion is directly evaluated using the data of the horizontal dense array in different depths at the site. The comparison between Fourier spectra of torsional motion and identified transfer functions reveals the peaks at the same frequencies. The wave equation including torsion and horizontal motion coupling is introduced and solved for the layered media by applying wave propagation theory. Using the developed model, the effects of torsional motion with horizontal motion coupling on soil transfer function are numerically examined. Splitting and low amplification at resonance frequencies are confirmed by the results of numerical analysis. Furthermore, the ground motion in two horizontal directions at the site is simulated using site geotechnical specification and optimizing the model parameters. The simulated and recorded motions demonstrate good agreement that is used to validate the hypothesis. In addition, the spectral density of torsional ground motions are compared with the calculated one and found to be well predicted by the model. Finally, the results are used to explain the overestimation of damping in back-calculation of dynamic soil properties using vertical array data in small strain level. Copyright © 2003 John Wiley & Sons, Ltd. [source] Genomic features of lactic acid bacteria effecting bioprocessing and healthFEMS MICROBIOLOGY REVIEWS, Issue 3 2005Todd R. Klaenhammer Abstract The lactic acid bacteria are a functionally related group of organisms known primarily for their bioprocessing roles in food and beverages. More recently, selected members of the lactic acid bacteria have been implicated in a number of probiotic roles that impact general health and well-being. Genomic analyses of multiple members of the lactic acid bacteria, at the genus, species, and strain level, have now elucidated many genetic features that direct their fermentative and probiotic roles. This information is providing an important platform for understanding core mechanisms that control and regulate bacterial growth, survival, signaling, and fermentative processes and, in some cases, potentially underlying probiotic activities within complex microbial and host ecosystems. [source] The use of killer sensitivity patterns for biotyping yeast strains: the state of the art, potentialities and limitationsFEMS YEAST RESEARCH, Issue 6 2007Pietro Buzzini Abstract In recent years molecular techniques have been the most useful tools for the unequivocal identification of undetermined strains at the species level. In many instances, however, a further discrimination at the strain level (biotyping) is required, such as during epidemiological investigations, in which the distribution of pathogenic microorganisms is studied, and for patent protection purposes. Although molecular methods are routinely used also for yeast biotyping, several nonmolecular techniques have been proposed. One of these, the determination of the killer sensitivity pattern (KSP) towards a panel of selected killer toxins has proven to be a good auxiliary method. Despite the plethora of studies published, the potential and limitations of the determination of KSPs have never been critically evaluated. In this review the use of this nonmolecular technique as a biotyping tool is discussed and compared with some currently used DNA-based procedures. In addition, methodological, mechanistic and ecological implications are evaluated. [source] Development of a molecular method for the typing of Brettanomyces bruxellensis (Dekkera bruxellensis) at the strain levelJOURNAL OF APPLIED MICROBIOLOGY, Issue 2 2007C. Miot-Sertier Abstract Aims:, In recent years, Brettanomyces/Dekkera bruxellensis has caused increasingly severe quality problems in the wine industry. A typing method at the strain level is needed for a better knowledge of the dispersion and the dynamics of these yeasts from grape to wine. Methods and Results:, Three molecular tools, namely random-amplified polymorphic DNA, PCR fingerprinting with microsatellite oligonucleotide primers and SAU-PCR, were explored for their relevance to typing strains of Brettanomyces bruxellensis. The results indicated that discrimination of each individual strain was not possible with a single PCR typing technique. We described a typing method for B. bruxellensis based on restriction enzyme analysis and pulse field gel electrophoresis (REA-PFGE). Results showed that electrophoretic profiles were reproducible and specific for each strain under study. Conclusions:, Consequently, REA-PFGE should be considered for the discrimination of B. bruxellensis strains. This technique allowed a fine discrimination of B. bruxellensis, as strains were identified by a particular profile. Significance and Impact of the Study:, This study constitutes a prerequisite for accurate and appropriate investigations on the diversity of strains throughout the winemaking and ageing process. Such studies will probably give clearer and more up-to-date information on the origin of the presence of Brettanomyces in wine after vinification when they are latent spoilage agents. [source] Saccharomyces cerevisiae wine yeast populations in a cold region in Argentinean Patagonia.JOURNAL OF APPLIED MICROBIOLOGY, Issue 4 2002A study at different fermentation scales Aims: To study the diversity and dynamics of indigenous Saccharomyces wine populations during Malbec spontaneous fermentation, a representative Patagonian red wine, at both industrial and laboratory scale. Methods and Results: Two molecular techniques, including restriction fragment length polymorphism of mitochondrial (mt) DNA and polymorphism of amplified , interspersed element sequences, were used for characterization of indigenous yeasts at strain level. The mtDNA restriction patterns showed the major discriminative power; however, by combining the two molecular approaches it was possible to distinguish a larger number of strains and, therefore, draw more representative conclusions about yeast diversity. Although a great diversity of wild Saccharomyces cerevisiae strains was observed, only nine represented more than half of the total Saccharomyces yeast biota analysed; five of these were common and took over the Malbec must fermentation in both vinifications. Conclusions: Many different indigenous S. cerevisiae strains were identified; nevertheless, the dominant strains in both industrial and laboratory vinification processes were just a few and the same. Significance and Impact of the Study: Small-scale fermentation appears to be a valuable tool in winemaking, one especially helpful in evaluating microbiological aspects of as well as possible interactions between inoculated selected strains and native strains. [source] Genotypic and phenotypic heterogeneity among lactococci isolated from traditional Pecorino Sardo cheeseJOURNAL OF APPLIED MICROBIOLOGY, Issue 2 2000L. Mannu Twenty-nine Lactococcus lactis isolates from one traditional 24 h-old Pecorino Sardo cheese were characterized phenotypically, technologically and genotypically in order to assess the biodiversity within this wild microbial population. Two DNA-based techniques, plasmid profiling and PFGE, were used for the genetic typing of the isolates. All 29 isolates were characterized at strain level and eight different genotypes were recognized. In addition, by combining the results from plasmid profile analysis and PFGE, it was possible to identify closely related isolates probably belonging to the same clonal lineage. The dominant biotype was identified in the 24 h-old cheese, as were the strains believed to act as starters for the curd. Atypical lactococci, able to grow in 6·5% NaCl, were isolated. The results suggest that wild bacterial populations should be preserved in order to protect the traditional raw milk cheeses, and to select new starter strains for the dairy industry. [source] EBSD and TEM investigation of the hot deformation substructure characteristics of a type 316L austenitic stainless steelJOURNAL OF MICROSCOPY, Issue 3 2004P. Cizek Summary The evolution of crystallographic texture and deformation substructure was studied in a type 316L austenitic stainless steel, deformed in rolling at 900 °C to true strain levels of about 0.3 and 0.7. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) were used in the investigation and a comparison of the substructural characteristics obtained by these techniques was made. At the lower strain level, the deformation substructure observed by EBSD appeared to be rather poorly developed. There was considerable evidence of a rotation of the pre-existing twin boundaries from their original orientation relationship, as well as the formation of highly distorted grain boundary regions. In TEM, at this strain level, the substructure was more clearly revealed, although it appeared rather inhomogeneously developed from grain to grain. The subgrains were frequently elongated and their boundaries often approximated to traces of {111} slip planes. The corresponding misorientations were small and largely displayed a non-cumulative character. At the larger strain, the substructure within most grains became well developed and the corresponding misorientations increased. This resulted in better detection of sub-boundaries by EBSD, although the percentage of indexing slightly decreased. TEM revealed splitting of some sub-boundaries to form fine microbands, as well as the localized formation of microshear bands. The substructural characteristics observed by EBSD, in particular at the larger strain, generally appeared to compare well with those obtained using TEM. With increased strain level, the mean subgrain size became finer, the corresponding mean misorientation angle increased and both these characteristics became less dependent on a particular grain orientation. The statistically representative data obtained will assist in the development of physically based models of microstructural evolution during thermomechanical processing of austenitic stainless steels. [source] Biomechanical consequences of an isolated overload on the human vertebral bodyJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 5 2000David L. Kopperdahl The biomechanical consequences of an isolated overload to the vertebral body may play a role in the etiology of vertebral fracture. In this context, we quantified residual strains and reductions in stiffness and ultimate load when vertebral bodies were loaded to various levels beyond the elastic regimen and related these properties to the externally applied strain and bone density. Twenty-three vertebral bodies (T11-L4, from 23 cadavers aged 20,90 years) were loaded once in compression to a randomized nominal strain level between 0.37 and 4.5%, unloaded, and then reloaded to 10% strain. Residual strains of up to 1.36% developed on unloading and depended on the applied strain (r2 = 0.85) but not on density (p = 0.25). Percentage reductions in stiffness and ultimate load of up to 83.7 and 52.5%, respectively, depended on both applied strain (r2 = 0.90 and r2 = 0.32, respectively) and density (r2 = 0.23 and r2 = 0.22, respectively). Development of residual strains is indicative of permanent deformations, whereas percentage reductions in stiffness are direct measures of effective mechanical damage. These results therefore demonstrate that substantial mechanical damage,which is not visible from radiographs,can develop in the vertebral body after isolated overloads, as well as subtle but significant permanent deformations. This behavior is similar to that observed previously for cylindrical cores of trabecular bone. Taken together, these findings indicate that the damage behavior of the lumbar and lower thoracic vertebral body is dominated by the trabecular bone and may be an important factor in the etiology of vertebral fracture. [source] Discrepancies between the phenotypic and genotypic characterization of Lactococcus lactis cheese isolatesLETTERS IN APPLIED MICROBIOLOGY, Issue 6 2006M. De La Plaza Abstract Aims:, The use of randomly amplified polymorphic DNA (RAPD)-PCR fingerprinting and plasmid profiles to determine at the strain level, the similarity of Lactococcus lactis isolates obtained during sampling of traditional cheeses and to verify its correspondence to the selected phenotypic characteristics. Methods and Results:, A total of 45 L. lactis isolates were genotypically analysed by RAPD-PCR fingerprinting and plasmid patterns. Phenotypic traits used to compare strains were proteolytic, acidifying, aminotransferase (aromatic and branched chain aminotransferase) and , -ketoisovalerate decarboxylase (Kivd) activities. The results show that 23 isolates could be grouped in clusters that exhibited 100% identity in both their RAPD and plasmid patterns, indicating the probable isolation of dominant strains during the cheese sampling process. However, there were phenotypic differences between isolates within the same cluster that included the loss of relevant technological properties such as proteinase activity and acidifying capacity or high variation in their amino acid converting enzyme activities. Likewise, the analysis of a specific attribute, Kivd activity, indicated that 7 of 15 isolates showed no detectable activity despite the presence of the encoding (kivd) gene. Conclusion:, Phenotypic differences found between genotypically similar strains of L. lactis strains could be linked to differences in enzymatic expression. Significance and Impact of the Study:, Phenotypic analysis of L. lactis isolates should be considered when selecting strains with new cheese flavour forming capabilities. [source] Major microbiota of lactic acid bacteria from Matsoni, a traditional Georgian fermented milkANIMAL SCIENCE JOURNAL, Issue 1 2007Kenji UCHIDA ABSTRACT A total of 26 samples of Matsoni were collected in Georgia. From these samples 80 strains of lactic acid cocci and 173 strains of lactobacilli were isolated. The number of lactic acid bacteria varied between 105 and 1010 colony forming unit (CFU)/mL. All the isolated lactic acid bacteria were thermophilic bacteria that could grow at 45°C. The predominant lactic acid bacteria were Streptococcus thermophilus and Lactobacillus delbrueckii spp. bulgaricus in 25 samples of Matsoni, while Lactobacillus helveticus was also a predominant species, together with the two previous species in one sample of Matsoni. We showed there was diversity in both S. thermophilus and L. delbrueckii spp. bulgaricus at the strain level by randomly amplified polymorphic DNA analysis. [source] Age-associated changes in viscoelastic properties of the bovine temporomandibular joint discEUROPEAN JOURNAL OF ORAL SCIENCES, Issue 1 2006Eiji Tanaka To test the hypothesis that compressive properties of the temporomandibular joint (TMJ) disc change with age, we investigated its viscoelastic properties and stress-relaxation behavior under compression. Compressive stress-relaxation tests were performed in different regions of bovine discs of various ages. For each disc, specimens were derived from three different regions (anterior, central, and posterior). For four strain levels (5, 10, 15, and 20%), a stress-relaxation test was conducted over a 5-min period. Values of the instantaneous modulus, E0, appeared to be larger in the anterior than in the posterior region of the disc, irrespective of age. The E0 value increased with age, especially in the central region. Values of the relaxed modulus, ER, also increased significantly with age. There were no regional differences in values of the relaxed modulus. Under stress-relaxation, the relaxation time became longer with age, especially in the posterior region. The results suggest that the compressive properties, instantaneous and relaxed moduli, increase with age, while the relaxation time becomes longer. This implies that the TMJ disc becomes harder with age. Furthermore, the compressive properties of the TMJ disc are region-specific. As a result of the harder disc, it is likely that the TMJ becomes more vulnerable to secondary damage, such as fracture and tissue degradation. [source] EBSD Study on Deformation Twinning in AZ31 Magnesium Alloy During Quasi-in-Situ Compression,ADVANCED ENGINEERING MATERIALS, Issue 10 2008J. Yang In this paper, the authors use the electron back-scatter diffraction (EBSD) technique to study the evolution of texture and microstructure during the deformation twinning process of AZ31 magnesium alloy under quasi-in-situ compression to several strain levels along two different directions. The aims of the current study were to analyze the influence of initial texture, grain size and plastic strain on the deformation twinning behavior. [source] Magnetic Field-Induced Phase Transformation in NiMnCoIn Magnetic Shape-Memory Alloys,A New Actuation Mechanism with Large Work OutputADVANCED FUNCTIONAL MATERIALS, Issue 7 2009Haluk E. Karaca Abstract Magnetic shape memory alloys (MSMAs) have recently been developed into a new class of functional materials that are capable of magnetic-field-induced actuation, mechanical sensing, magnetic refrigeration, and energy harvesting. In the present work, the magnetic &!hyphen;field-induced martensitic phase transformation (FIPT) in Ni45Mn36.5Co5In13.5 MSMA single crystals is characterized as a new actuation mechanism with potential to result in ultra-high actuation work outputs. The effects of the applied magnetic field on the transformation temperatures, magnetization, and superelastic response are investigated. The magnetic work output of NiMnCoIn alloys is determined to be more than 1,MJ m,3 per Tesla, which is one order of magnitude higher than that of the most well-known MSMAs, i.e., NiMnGa alloys. In addition, the work output of NiMnCoIn alloys is orientation independent, potentially surpassing the need for single crystals, and not limited by a saturation magnetic field, as opposed to NiMnGa MSMAs. Experimental and theoretical transformation strains and magnetostress levels are determined as a function of crystal orientation. It is found that [111]-oriented crystals can demonstrate a magnetostress level of 140,MPa T,1 with 1.2% axial strain under compression. These field-induced stress and strain levels are significantly higher than those from existing piezoelectric and magnetostrictive actuators. A thermodynamical framework is introduced to comprehend the magnetic energy contributions during FIPT. The present work reveals that the magnetic FIPT mechanism is promising for magnetic actuation applications and provides new opportunities for applications requiring high actuation work-outputs with relatively large actuation frequencies. One potential issue is the requirement for relatively high critical magnetic fields and field intervals (1.5,3,T) for the onset of FIPT and for reversible FIPT, respectively. [source] Skin friction features of drilled CIP piles in sand from pile segment analysisINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 7 2008Sungjune Lee Abstract Numerical pile segment analysis is conducted in this study with an advanced soil model to investigate the skin friction behaviour of a drilled Cast-In-Place (CIP) pile installed in sand. Although the interface between the sand and pile is considered rough, thin elements adjacent to the pile are used to include effects of localized shear. Unit weights of fluid concrete and accompanied changes in stress are considered as the effects of pile installation. Changes in effective stresses are the most prominent effect due to pile installation with a change in direction of the major principal stress from the vertical to the radial direction. Shear behaviour of the sand at the interface during the early shear stage is related to the contractive tendency of the sand at small strain levels. Changes in the stress field around the pile with little changes in volumetric strain take place during the early shear stage. Stress redistributions during the early shear stage depend on the direction of the major principal stress before shear. Results of the pile segment analyses for drilled CIP piles show good agreement with design methods. Parametric studies are used to characterize the effects of sand density and pile diameter on the skin friction behaviour of drilled CIP piles. Copyright © 2007 John Wiley & Sons, Ltd. [source] Directional response of a reconstituted fine-grained soil,Part I: experimental investigationINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 13 2006Daniele Costanzo Abstract This paper discusses the results of a large experimental program designed to investigate in a systematic manner the main features of the incremental response of fine-grained soils. The results are obtained from triaxial stress probing experiments carried out on a French silty clay (Beaucaire Marl). All the tests have been performed on reconstituted specimens, normally consolidated to an initial state which is either isotropic or anisotropic. In the interpretation of the experimental results, extensive use is made of the concept of strain response envelope. The response envelopes obtained for different stress increment magnitudes are remarkably consistent with each other and indicate an inelastic and irreversible material response, i.e. a strong dependence on the stress increment direction, also at relatively small strain levels. A companion paper (Int. J. Numer. Anal. Meth. Geomech., this issue, 2006) assesses the performance of some advanced constitutive models in reproducing the behaviour of reconstituted Beaucaire Marl as observed in this experimental program. Copyright © 2006 John Wiley & Sons, Ltd. [source] Two-level multiscale enrichment methodology for modeling of heterogeneous platesINTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING, Issue 9 2009Caglar OskayArticle first published online: 15 JUN 200 Abstract A new two-level multiscale enrichment methodology for analysis of heterogeneous plates is presented. The enrichments are applied in the displacement and strain levels: the displacement field of a Reissner,Mindlin plate is enriched using the multiscale enrichment functions based on the partition of unity principle; the strain field is enriched using the mathematical homogenization theory. The proposed methodology is implemented for linear and failure analysis of brittle heterogeneous plates. The eigendeformation-based model reduction approach is employed to efficiently evaluate the non-linear processes in case of failure. The capabilities of the proposed methodology are verified against direct three-dimensional finite element models with full resolution of the microstructure. Copyright © 2009 John Wiley & Sons, Ltd. [source] An in situ method for the study of strain broadening using synchrotron X-ray diffractionJOURNAL OF APPLIED CRYSTALLOGRAPHY, Issue 4 2007C. C. Tang A tensonometer for stretching metal foils has been constructed for the study of strain broadening in X-ray diffraction line profiles. This device, which is designed for use on powder diffractometers and was tested on Station 2.3 at Daresbury Laboratory, allows in situ measurements to be performed on samples under stress. It can be used for data collection in either transmission or reflection modes using either symmetric or asymmetric diffraction geometries. As a test case, measurements were carried out on an 18,µm-thick copper foil experiencing strain levels of up to 5% using both symmetric reflection and symmetric transmission diffraction. All the diffraction profiles displayed peak broadening and asymmetry which increased with strain. The measured profiles were analysed by the fundamental-parameters approach using the TOPAS peak-fitting software. All the observed broadened profiles were modelled by convoluting a refineable diffraction profile, representing the dislocation and crystallite size broadening, with a fixed instrumental profile predetermined using high-quality LaB6 reference powder. The deconvolution process yielded `pure' sample integral breadths and asymmetry results which displayed a strong dependence on applied strain and increased almost linearly with applied strain. Assuming crystallite size broadening in combination with dislocation broadening arising from f.c.c. a/2,110,{111} dislocations, the variation of mechanical property with strain has been extracted. The observation of both peak asymmetry and broadening has been interpreted as a manifestation of a cellular structure with cell walls and cell interiors possessing high and low dislocation densities. [source] Quantitative Ultrasound Does Not Reflect Mechanically Induced Damage in Human Cancellous BoneJOURNAL OF BONE AND MINERAL RESEARCH, Issue 12 2000P. H. F. Nicholson Abstract This study investigated the ability of quantitative ultrasound (QUS) to detect reductions in the elastic modulus of cancellous bone caused by mechanical damage. Ultrasonic velocity and attenuation were measured using an in-house parametric imaging system in 46 cancellous bone cores from the human calcaneus. Each core was subjected to a mechanical testing regime to (a) determine the predamage elastic modulus, (b) induce damage by applying specified strains in excess of the yield strain, and (c) measure the postdamage elastic modulus. The specimens were divided into four groups: a control group subjected to a nominally nondestructive 0.7% maximum strain (,m) and three damage groups subjected to increasing strain levels (,m = 1.5, 3.0, and 4.5%). QUS measurements before and after the mechanical testing showed no significant differences between the control group and damage groups, despite highly significant (p < 0.001) reductions in the elastic modulus of up to 72%. These results indicate that current QUS techniques do not intrinsically reflect the elastic properties of cancellous bone. This is consistent with ultrasonic properties being determined by other factors (apparent density and/or architecture), which normally are associated strongly with elastic properties, but only when bone is mechanically intact. Clinically, this implies that ultrasound cannot be expected to detect bone fragility in the absence of major changes in bone density and/or trabecular architecture. [source] EBSD and TEM investigation of the hot deformation substructure characteristics of a type 316L austenitic stainless steelJOURNAL OF MICROSCOPY, Issue 3 2004P. Cizek Summary The evolution of crystallographic texture and deformation substructure was studied in a type 316L austenitic stainless steel, deformed in rolling at 900 °C to true strain levels of about 0.3 and 0.7. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) were used in the investigation and a comparison of the substructural characteristics obtained by these techniques was made. At the lower strain level, the deformation substructure observed by EBSD appeared to be rather poorly developed. There was considerable evidence of a rotation of the pre-existing twin boundaries from their original orientation relationship, as well as the formation of highly distorted grain boundary regions. In TEM, at this strain level, the substructure was more clearly revealed, although it appeared rather inhomogeneously developed from grain to grain. The subgrains were frequently elongated and their boundaries often approximated to traces of {111} slip planes. The corresponding misorientations were small and largely displayed a non-cumulative character. At the larger strain, the substructure within most grains became well developed and the corresponding misorientations increased. This resulted in better detection of sub-boundaries by EBSD, although the percentage of indexing slightly decreased. TEM revealed splitting of some sub-boundaries to form fine microbands, as well as the localized formation of microshear bands. The substructural characteristics observed by EBSD, in particular at the larger strain, generally appeared to compare well with those obtained using TEM. With increased strain level, the mean subgrain size became finer, the corresponding mean misorientation angle increased and both these characteristics became less dependent on a particular grain orientation. The statistically representative data obtained will assist in the development of physically based models of microstructural evolution during thermomechanical processing of austenitic stainless steels. [source] TEXTURE PROFILE ANALYSIS , HOW IMPORTANT ARE THE PARAMETERS?JOURNAL OF TEXTURE STUDIES, Issue 5 2010ANDREW J. ROSENTHAL ABSTRACT A starch-glycerol gel was subjected to a two-bite compression test using two sample-instrument geometries, various speeds of compression and strain levels, both with lubrication or not. Results were interpreted using the primary characteristic terminology previously defined in Texture Profile Analysis. Compression speeds from 0.1 to 10 m/s showed a logarithmic relationship with hardness, cohesiveness, corrected cohesiveness and adhesiveness. Gels survived compression to strains of 0.90 without failing, strain levels from 0.25 to 0.90 resulted in an exponential rise in hardness with increasing strain and linear reduction in corrected cohesiveness. Lubrication had no significant influence on any of the measured parameters and an application of force with different sample-instrument geometry revealed that parallel plates and plungers only had an influence on gel hardness. Caution is urged when researchers modify the test protocol from 75% deformation with parallel plates. A minimum crosshead speed of 2 mm/s is recommended. PRACTICAL APPLICATIONS Texture Profile Analysis has been widely applied to test solid and semisolid foods; however, some researchers deviate from the original test protocol. This article attempts to show how modifying the parameters in the test protocol can influence the apparent properties of the sample. [source] Large Enhancement in Conductivity of Polyaniline Films by Cold StretchingMACROMOLECULAR CHEMISTRY AND PHYSICS, Issue 10 2010Hong-Mei Xiao Abstract The hot-stretching method has been well accepted for enhancing the electrical conductivity of conducting polymer films. High temperature is the prerequisite to soften the polymer to highly align and elongate the polymeric molecular chains. In this study, the cold-stretching method is proposed for the first time to enhance the conductivity of conducting polymeric films. Polyaniline (PANI) films are stretched at room temperature to different strain levels. It is observed that the applied strain has significant effects on the morphology, molecular chain structure, crystallinity, and crosslinking of the PANI films. As a result, the conductivity of PANI films is effectively increased by the cold-stretching process. Particularly, a maximum conductivity with an 18.4-fold increase in the direction parallel to the stretched direction is obtained when the elastic limit strain is applied. Compared to hot stretching, cold stretching is unique due to the extremely low dimensional change and very high efficiency achieved. [source] In situ deformation of thin films on substratesMICROSCOPY RESEARCH AND TECHNIQUE, Issue 3 2009Marc Legros Abstract Metallic thin-film plasticity has been widely studied by using the difference between the coefficients of thermal expansion of the film and the underlying substrate to induce stress. This approach is commonly known as the wafer curvature technique, based on the Stoney equation, which has shown that thinner films have higher yield stresses. The linear increase of the film strength as a function of the reciprocal film thickness, down to a couple hundred nanometers, has been rationalized in terms of threading and interfacial dislocations. Polycrystalline films also show this kind of dependence when the grain size is larger than or comparable to the film thickness. In situ TEM performed on plan-view or cross-section specimens faithfully reproduces the stress state and the small strain levels seen by the metallic film during wafer curvature experiments and simultaneously follows the change in its microstructure. Although plan-view experiments are restricted to thinner films, cross-sectional samples where the film is reduced to a strip (or nanowire) on its substrate are a more versatile configuration. In situ thermal cycling experiments revealed that the dislocation/interface interaction could be either attractive or repulsive depending on the interfacial structure. Incoherent interfaces clearly act as dislocation sinks, resulting in a dislocation density drop during thermal cycles. In dislocation-depleted films (initially thin or annealed), grain boundaries can compensate for the absence of dislocations by either shearing the film similarly to threading dislocations or through fast diffusion processes. Conversely, dislocations are confined inside the film by image forces in the cases of epitaxial interfaces on hard substrates. To increase the amount of strain seen by a film, and to decouple the effects of stress and temperature, compliant substrates can also be used as support for the metallic film. The composite can be stretched at a given temperature using heating/cooling straining holders. Other in situ TEM methods that served to reveal scaling effects are also reviewed. Finally, an alternate method, based on a novel bending holder that can stretch metallic films on rigid substrates, is presented. Microsc. Res. Tech., 2009. © 2009 Wiley-Liss, Inc. [source] | ||||||||||||||||||||||||||||||||||