Home About us Contact
|
Home About us Contact | ||
|
|
||
Structural Reinforcement (structural + reinforcement)
Selected AbstractsCorrelation of dystrophin,glycoprotein complex and focal adhesion complex with myosin heavy chain isoforms in rat skeletal muscleACTA PHYSIOLOGICA, Issue 4 2009S. Masuda Abstract Aim:, The dystrophin,glycoprotein complex (DGC) and focal adhesion complex (FAC) are transmembrane structures in muscle fibres that link the intracellular cytoskeleton to the extracellular matrix. DGC and FAC proteins are abundant in slow-type muscles, indicating the structural reinforcement which play a pivotal role in continuous force output to maintain posture for long periods. The aim of the present study was to examine the expression of these structures across fast-type muscles containing different myosin heavy chain (MHC) isoform patterns which reflect the fatigue-resistant characteristics of skeletal muscle. Methods:, We measured the expression of dystrophin and ,1 integrin (representative proteins of DGC and FAC respectively) in plantaris, extensor digitorum longus, tibialis anterior, red and white portions of gastrocnemius, superficial portion of vastus lateralis and diaphragm, in comparison with soleus (SOL) and cardiac muscle from rats. Results:, The expression of dystrophin and ,1 integrin correlated positively with the percentage of type I, IIa and IIx MHC isoforms and negatively with that of type IIb MHC isoform in fast-type skeletal muscles, and their expression was abundant in SOL and cardiac muscle. Conclusion:, Our results support the idea that DGC and FAC are among the factors that explain the fatigue-resistant property not only of slow-type but also of fast-type skeletal muscles. [source] Dangers relating to fires in carbon-fibre based composite materialFIRE AND MATERIALS, Issue 4 2005Tommy Hertzberg Abstract Inhalable carbon fibres have been suspected to pose similar threats to human health as asbestos fibres. It is well-known that fibres having a diameter of less than 3 µm might be inhaled and transported deep into the human respiratory system. Some composite materials use carbon fibres as structural reinforcement. These fibres do not pose any risks as such as they are firmly connected to the laminate and surrounded by a polymer matrix. Also, these fibres typically have diameters >6 µm and thus, are not inhalable. However, if the material is exposed to a fire, the carbon material might be oxidized and fractionated and thereby, inhalable fibres might be generated into the fire smoke. The capability of carbon fibre-based composite material to produce dangerous inhalable fibres from different combustion scenarios has been investigated. It was found that the risk of fires generating inhalable carbon fibres is related to the surface temperature, the oxygen level and the airflow field close to the material surface. The temperatures necessary for oxidation of the carbon fibre is so high that it is possible that only a flashover situation will pose any real danger. Other possible danger scenarios are highly intense fires (e.g. a liquid fuel fire), or situations where structural damage is part of the fire scenario. Copyright © 2005 John Wiley & Sons, Ltd. [source] The effect of low-temperature blanching on the quality of fresh and frozen/thawed mashed potatoesINTERNATIONAL JOURNAL OF FOOD SCIENCE & TECHNOLOGY, Issue 5 2006Cristina Fernández Summary The effect of low-temperature blanching (LTB) prior to cooking on colour, textural, firmness and oscillatory parameters, sensory attributes and overall acceptability of either fresh or frozen/thawed mashed potatoes was studied using response surface methodology (RSM) to establish the optimum temperature and time for blanching in both types of mashed potatoes. A central composite rotatable design was used to study the effects of variation in levels of blanching temperature (57.93,72.07 °C) and time (15.86,44.14 min) on the quality parameters. Stationary points showing maximum thickening had critical temperatures (approximately 67,69 °C) and times (approximately 26,30 min) in the ranges of temperature and time used for each independent variable for both fresh and frozen/thawed mashed potato. Results showed a high correlation between structural reinforcement and overall acceptability under optimum experimental blanching conditions. This demonstrates the potential of this experimental approach in terms of tailoring physical properties to predetermined levels in order to meet consumer preferences in mashed potatoes, and of altering the changes that occur after freezing and thawing. [source] Efficient utilization of plastic waste through product design and process adaptation: A case study on stiffness enhancement of beams produced from plastic lumberADVANCES IN POLYMER TECHNOLOGY, Issue 3 2008Cristian Pio Abstract The aim of the present work is the development of a method for structural reinforcement of beams obtained by in-mold extrusion of plastics from solid urban waste. The beams obtained by in-mold extrusion are commonly used for outdoor furniture and structures. The material used for such applications is mainly composed of low-density polyethylene derived from bags and films, with small amounts of high density polyethylene and polypropylene, as well as traces of polyethylene terephthalate. This material is usually referred to as "plastic lumber." Plastic lumber products have a low stiffness, which results in high deflections under flexural loads, particularly under creep loading. In this study, reinforcing rods of high aspect ratio were incorporated into plastic lumber beams in specific positions with respect to the cross section of the beam. The reinforcement of the plastic lumber beams with fine rods is introduced in the typical intrusion process used for the production of unreinforced beams. Glass fiber reinforced pultruded rods were chosen for this purpose from a preliminary evaluation of different materials. Different diameter glass fiber reinforced pultruded rods, including surface-abraded systems to increase the roughness, were used for the reinforcement of plastic lumber beams. The reinforced beams were tested in terms of flexural stiffness, creep resistance, and pullout resistance of the embedded rods. The results obtained from the mechanical tests showed a significant enhancement of flexural stiffness and creep resistance behavior. The performance at higher stress levels was shown to be significantly dependent on the interfacial adhesion between rods and polymer matrix. © 2009 Wiley Periodicals, Inc. Adv Polym Techn 27:133,142, 2008; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.20131 [source] The influence of porosity on the Phillips Cr/silica catalyst 2.JOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 3 2009Polyethylene elasticity Abstract The Phillips Cr/silica catalyst produces low levels of long chain branching (LCB) in polyethylene, which have a powerful influence on industrial molding behavior. Although many catalyst and reactor variables determine the degree of LCB, perhaps the most significant of these is the morphology of the silica support. In this study many different types of silicas were converted into Cr/silica catalysts, which were tested in ethylene polymerization, and the resultant polymer elasticity was then determined. In some experiments, the surface area of the catalyst seemed to correlate quite well with polymer elasticity. In other tests, however, no connection with surface area was evident but the pore volume was quite influential. Together, all these studies suggest that it is the degree of structural reinforcement of the silica matrix, rather than any one physical measurement of porosity, that influences elasticity. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 845,865, 2009 [source] | ||||||||||