Home About us Contact
|
Home About us Contact | ||
|
|
||
Specimen Size (specimen + size)
Selected AbstractsStrategies for Improving Tensile Ductility of Bulk Nanostructured Materials,ADVANCED ENGINEERING MATERIALS, Issue 8 2010Yonghao Zhao Abstract The low ductility that is consistently associated with bulk nanostructured (NS) materials has been identified as perhaps the single most critical issue that must be resolved before this novel class of materials can be used in a wide variety of applications. Not surprisingly, a number of published studies, published mostly after 2000, identify the issue of low ductility and describe strategies to improve ductility. Details of these strategies were discussed in review papers published by Koch and Ma in 2005 and 2006, respectively.15,16 In view of continued efforts and recent results, in this paper we describe progress in attempting to address the low ductility of NS materials, after 2006. We first analyze the fundamental reasons for the observed low ductility of bulk NS materials, and summarize early (prior to 2006) attempts to enhance the ductility of bulk NS materials, which often sacrificed the strength. Then, we review recent progress in developing strategies for improving the tensile ductility of bulk NS materials, which involve mainly microstructure modifications, after 2006. Different from early efforts, these new strategies strive to increase the tensile ductility while increasing/maintaining the strength simultaneously. In addition, the influence of tensile testing conditions, including temperature, strain rate, tensile specimen size and geometry, and strain measurement methods, on tensile ductility of NS materials will also be reviewed. Finally, we identify several issues that will require further, in depth analysis in the future. [source] Fretting fatigue limit as a short crack problem at the edge of contactFATIGUE & FRACTURE OF ENGINEERING MATERIALS AND STRUCTURES, Issue 5 2004Y. KONDO ABSTRACT This paper proposes a local stress concept to evaluate the fretting fatigue limit for contact edge cracks. A unique S,N curve based on the local stress could be obtained for a contact edge crack irrespective of mechanical factors such as contact pressure, relative slip, contact length, specimen size and loading type. The analytical background for the local stress concept was studied using FEM analysis. It was shown that the local stress uniquely determined the ,K change due to crack growth as well as the stress distribution near the contact edge. The condition that determined the fretting fatigue limit was predicted by combining the ,K change due to crack growth and the ,Kth for a short crack. The formation of a non-propagating crack at the fatigue limit was predicted by the model and it was experimentally confirmed by a long-life fretting fatigue test. [source] Strain localization in sand: an overview of the experimental results obtained in Grenoble using stereophotogrammetryINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 4 2004Jacques Desrues Abstract Experimental results are presented from the extensive program of drained plane strain compression tests on sand carried out in Grenoble over the last two decades. Systematic analysis of photographs of the deforming specimen allowed for measuring deformations and determining strain fields throughout the test, that is: prior to, at, and after the onset of strain localization. The principles, details and accuracy of the procedure are described, as well as its suitability to properly depict the patterns of deformation. Findings concerning the occurrence and progression of strain localization are discussed. The issues of shear band orientation and thickness are addressed, as well as temporary and persistent complex localization patterns, and the volumetric behaviour inside a band after its formation. The influence of such variables as initial state of the sand (effective stress and relative density), specimen size and slenderness, as well as grain size, is discussed. Copyright © 2004 John Wiley & Sons, Ltd [source] Characterization of dilute species within CVD-grown silicon nanowires doped using trimethylboron: protected lift-out specimen preparation for atom probe tomographyJOURNAL OF MICROSCOPY, Issue 2 2010T. J. PROSA Summary Three-dimensional quantitative compositional analysis of nanowires is a challenge for standard techniques such as secondary ion mass spectrometry because of specimen size and geometry considerations; however, it is precisely the size and geometry of nanowires that makes them attractive candidates for analysis via atom probe tomography. The resulting boron composition of various trimethylboron vapour,liquid,solid grown silicon nanowires were measured both with time-of-flight secondary ion mass spectrometry and pulsed-laser atom probe tomography. Both characterization techniques yielded similar results for relative composition. Specialized specimen preparation for pulsed-laser atom probe tomography was utilized and is described in detail whereby individual silicon nanowires are first protected, then lifted out, trimmed, and finally wet etched to remove the protective layer for subsequent three-dimensional analysis. [source] Effect of Activated Carbon Bed on Binder Removal from Ceramic Injection MoldingsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 3 2001Martin Trunec Weight losses during the binder removal from ceramic injection moldings that have been placed in beds of activated carbon powder and two types of alumina powder were compared. The effect of the specimen size and shape on debinding in a bed of activated carbon was investigated. Because of the structure of its particles, activated carbon powder allowed binder losses in ceramic moldings that consisted of submicrometer-sized particles to increase at a temperature of 130°C. The binder loss in a bed of activated carbon was dependent on the ratio of surface area to volume of the body that was extracted. Renewal of the sorption abilities of the bed of activated carbon after saturation with binder increased the rate of binder removal. [source] A method to predict triaxial residual stresses in plastic pipesPOLYMER ENGINEERING & SCIENCE, Issue 10 2004Z. W. Guan Significant hoop and longitudinal stresses are present in medium-density polyethylene (MDPE) pipe, arising from differential cooling from the inner and the outer surfaces of a pipe during production. Owing to the difficulty of directly measuring deformations, these stresses have hitherto been almost exclusively estimated indirectly from deflection measurements on large samples cut from the pipe wall. Furthermore, because of procedural problems, only uniaxial hoop or longitudinal stresses are normally attempted, and these are known to be specimen size,dependent. Similar problems are experienced with other polymeric pipes. In this paper, based on direct biaxial strain measurements on small samples cut from the pipe wall, a method to predict triaxial residual stress distributions through the pipe wall is presented. Thermal effects that generate residual stresses in plastic pipe were considered in the theory. The analytical solutions satisfy the self-equilibrating conditions for both the hoop and the longitudinal stresses. Also, the radial stress is shown to be insignificant through the wall thickness of a mildly thick pipe. Polym. Eng. Sci. 44:1828,1838, 2004. © 2004 Society of Plastics Engineers. [source] | ||||||||||