Home  About us  Contact
 

Reynolds Number Re (reynold + number_re)

Distribution by Scientific Domains
Engineering100%

Selected Abstracts

Heat transfer and fluid flow characteristics in a swirling impinging jet

HEAT TRANSFER - ASIAN RESEARCH (FORMERLY HEAT TRANSFER-JAPANESE RESEARCH), Issue 5 2005
Mamoru Senda
Abstract An experimental study on heat transfer and fluid flow has been carried out for a swirling round impinging jet. A thermosensitive liquid crystal sheet was used for the heat transfer measurements and the three velocity components were measured with LDV in the stagnation region for cases where the Swirl number Sw = 0.0, 0.22, and 0.45 at the Reynolds number Re = 8100. The formation of recirculation flow due to a swirl near the impinging wall was found to deteriorate the heat transfer coefficient in the stagnation region and results in a more uniform distribution of the Nusselt number with an increasing Swirl number. The heat transfer mechanism of the swirling impinging jet is discussed based on the flow characteristics of the mean velocities and turbulence quantities. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(5): 324,335, 2005; Published online in Wiley InterScience (www.interscience. wiley.com). DOI 10.1002/htj.20068 [source]

Effect of magnetic Reynolds number on the two-dimensional hydromagnetic flow around a cylinder

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS, Issue 12 2009
T. V. S. Sekhar
Abstract Numerical experiments have been conducted to study the effect of magnetic Reynolds number on the steady, two-dimensional, viscous, incompressible and electrically conducting flow around a circular cylinder. Besides usual Reynolds number Re, the flow is governed by the magnetic Reynolds number Rm and Alfvén number ,. The flow and magnetic field are uniform and parallel at large distances from the cylinder. The pressure Poisson equation is solved to find the pressure fields in the entire flow region. The effects of the magnetic field and electrical conductivity on the recirculation bubble, drag coefficient, standing vortex and pressure are presented and discussed. For low interaction parameter (N<1), the suppression of the flow-separation is nearly independent of the conductivity of the fluid, whereas for large interaction parameters, the conductivity of the fluid strongly influences the control of flow-separation. Copyright © 2008 John Wiley & Sons, Ltd. [source]

2D thermal/isothermal incompressible viscous flows

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS, Issue 4 2005
Alfredo Nicolás
Abstract 2D thermal and isothermal time-dependent incompressible viscous flows are presented in rectangular domains governed by the Boussinesq approximation and Navier,Stokes equations in the stream function,vorticity formulation. The results are obtained with a simple numerical scheme based on a fixed point iterative process applied to the non-linear elliptic systems that result after a second-order time discretization. The iterative process leads to the solution of uncoupled, well-conditioned, symmetric linear elliptic problems. Thermal and isothermal examples are associated with the unregularized, driven cavity problem and correspond to several aspect ratios of the cavity. Some results are presented as validation examples and others, to the best of our knowledge, are reported for the first time. The parameters involved in the numerical experiments are the Reynolds number Re, the Grashof number Gr and the aspect ratio. All the results shown correspond to steady state flows obtained from the unsteady problem. Copyright © 2005 John Wiley & Sons, Ltd. [source]

Solving high Reynolds-number viscous flows by the general BEM and domain decomposition method

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS, Issue 3 2005
Yongyan Wu
Abstract In this paper, the domain decomposition method (DDM) and the general boundary element method (GBEM) are applied to solve the laminar viscous flow in a driven square cavity, governed by the exact Navier,Stokes equations. The convergent numerical results at high Reynolds number Re = 7500 are obtained. We find that the DDM can considerably improve the efficiency of the GBEM, and that the combination of the domain decomposition techniques and the parallel computation can further greatly improve the efficiency of the GBEM. This verifies the great potential of the GBEM for strongly non-linear problems in science and engineering. Copyright © 2004 John Wiley & Sons, Ltd. [source]

Large eddy simulation of turbulent concentric annular channel flows

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS, Issue 12 2004
Nan-Sheng Liu
Abstract Fully developed turbulent concentric annular channel flow has been investigated numerically by use of large eddy simulation (LES) technique coupled with a localized one-equation dynamic subgrid-scale (SGS) model. The objective of this study is to deal with the behaviour of turbulent flow near the inner and outer walls of the concentric annular channel and to examine the effectiveness of LES technique for predicting the turbulent flow influenced by the transverse curvature effect. The computations are performed for the Reynolds number Re,=180, 395 and 640, based on an averaged friction velocity and the annular channel width with the inner and outer cylinder radius being Ri=1 and Ro=2. To validate the present approach, calculated results for turbulent pipe flow and concentric annular channel flow are compared with available experimental data and direct numerical simulation results, which confirms that the present approach can be used to study turbulent concentric annular channel flow satisfactorily. To elucidate turbulence characteristics in the concentric annular channel, some typical quantities, including the resolved velocity, turbulence intensity, turbulent eddy viscosity, SGS kinetic energy, SGS dissipation rate, Reynolds stress budgets, and turbulence structures based on the velocity fluctuations, are analysed. Copyright © 2004 John Wiley & Sons, Ltd. [source]