Propylene Diene Monomer (propylene + diene_monomer)

Distribution by Scientific Domains

Kinds of Propylene Diene Monomer

  • ethylene propylene diene monomer


  • Selected Abstracts


    The partial replacement of silica or calcium carbonate by halloysite nanotubes as fillers in ethylene propylene diene monomer composites

    JOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2009
    Pooria Pasbakhsh
    Abstract The effect of partial replacement of silica or calcium carbonate (CaCO3) by halloysite nanotubes (HNTs) on the curing behavior, tensile properties, dynamic mechanical properties, and morphological characteristics of ethylene propylene diene monomer (EPDM) composites was studied. Five different compositions of EPDM/Silica/HNT and EPDM/CaCO3/HNT compounds (i.e. 100/30/0, 100/25/5, 100/15/15, 100/5/25, and 100/0/30 parts per hundred rubber (phr)) were prepared on a two-roll mill. The results indicated that the replacement of CaCO3 by HNTs increased the tensile strength, elongation at break (Eb), and tensile modulus of composites from 0 to 30 phr of HNTs whereas for silica, the maximum tensile strength and Eb occurred at 5 phr loading of HNTs with an enhanced stress at 300% elongation (M300). The curing results show that, with replacement of silica or CaCO3 by HNTs, the cure time (t90) and cure rate (CRI) were decreased and increased, respectively. Scanning electron microscopy investigation confirmed that co-incorporation of 5 phr of HNTs with silica would improve the dispersion of silica and enhanced the interactions between fillers and EPDM matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009 [source]


    The composition, morphology, and mechanical properties of ethylene propylene diene monomer-encapsulated coal gangue powder/polypropylene composites

    POLYMER COMPOSITES, Issue 1 2010
    Ying Liu
    The ternary composites of coal gangue powder encapsulated by ethylene propylene diene monomer (EPDM) filled polypropylene (PP) were prepared to reduce the cost and control the microstructure aiming at high performance cost ratio materials. The result showed that EPDM can not only enhance the interaction between coal gangue powder and the matrix but also promote the dispersion of coal gangue powder. With the addition of coal gangue encapsulated by EPDM, the impact strength of composition dropped greatly, but it still kept about 11 kJ/m2 when the content of encapsulated coal gangue powder is more than 18 wt%. The tensile strength and fracture toughness (we) also dropped with the addition of encapsulated coal gangue powder, but only a small drop occurred when the content of encapsulated coal gangue powder is less than 18 wt% and great drop emerged when the content is larger than 18 wt%. Compared with coal gangue powder/PP binary composition, the ternary compositions involve higher content of coal gangue powder but present better properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers [source]


    Thermal and mechanical properties of dough modeling compound reinforced ethylene propylene diene monomer/silicon rubber composites

    POLYMER COMPOSITES, Issue 6 2006
    Weili Wu
    Ethylene propylene diene monomer (EPDM)/silicon rubber composite was prepared by adding dough-modeling compound (DMC). EPDM/silicon rubber is the matrix of the composite, and DMC is a disperse phase (reinforced phase). The morphology of the composite was studied by scanning electron microscopy, and it was found that the compatibility of DMC/EPDM/silicon rubber composite was good. The influence of the DMC and peroxide curing agents on the mechanical and thermal properties were studied. The results showed that the mechanical and thermal properties of the composite were best, when DMC/EPDM/silicon rubber was 80/25/75. The thermal properties of the composite prepared with added equivalent dicumyl peroxide was better than those with added benzoperoxide, but Shore A hardness and elongation at break are unchangeable. The integral properties of DMC reinforced EPDM/silicon rubber composite was much better than three raw materials. POLYM. COMPOS. 27:621,626, 2006. © 2006 Society of Plastics Engineers [source]


    Yielding behaviour of thermoplastic/elastomer blends cured by gamma irradiation

    POLYMER INTERNATIONAL, Issue 3 2001
    A Shaltout
    Abstract Mechanical blends of thermoplastic medium density polyethylene (MDPE) and elastomeric ethylene propylene diene monomer (EPDM) have been prepared with a fixed composition of 60/40,wt%. They have been used either in their gum form or loaded with two different reinforcing fillers, high abrasion furnace (HAF) carbon black or precipitated SiO2 (Hi Sil) of concentration 25,100,phr (parts per hundred parts of resin) with respect to the blend. Curing was achieved by gamma irradiation. Yielding properties (yield stress, yield strain and cold drawing) have been followed as a function of irradiation dose for different blend compositions. Yield stress values increased with irradiation dose and with the content of the reinforcing filler, but yield strain and cold drawing values decreased with irradiation dose and also with the filler content. The data obtained reveal that Hi Sil is more effective as a reinforcing filler, and the prepared blends are suitable for load-bearing applications. © 2001 Society of Chemical Industry [source]