Home  About us  Contact
 

Polymer Donor (polymer + donor)

Distribution by Scientific Domains
Polymers and Materials Science100%

Selected Abstracts

High-Yield Synthesis and Electrochemical and Photovoltaic Properties of Indene-C70 Bisadduct

ADVANCED FUNCTIONAL MATERIALS, Issue 19 2010
Youjun He
Abstract [6, 6]-Phenyl-C61 -butyric acid methyl ester (PC60BM) is the widely used acceptor material in polymer solar cells (PSCs). Nevertheless, the low LUMO energy level and weak absorption in visible region are its two weak points. For enhancing the solar light harvest, the soluble C70 derivative PC70BM has been used as acceptor instead of PC60BM in high efficiency PSCs in recent years. But, the LUMO level of PC70BM is the same as that of PC60BM, which is too low for the PSCs based on the polymer donors with higher HOMO level, such as poly (3-hexylthiophene) (P3HT). Here, a new soluble C70 derivative, indene-C70 bisadduct (IC70BA), is synthesized with high yield of 58% by a one-pot reaction of indene and C70 at 180 °C for 72 h. The electrochemical properties and electronic energy levels of the fullerene derivatives are measured by cyclic voltammetry. The LUMO energy level of IC70BA is 0.19 eV higher than that of PC70BM. The PSC based on P3HT with IC70BA as acceptor shows a higher Voc of 0.84 V and higher power conversion efficiency (PCE) of 5.64%, while the PSC based on P3HT/PC60BM and P3HT/PC70BM displays Voc of 0.59 V and 0.58 V, and PCE of 3.55% and 3.96%, respectively, under the illumination of AM1.5G, 100 mW cm,2. The results indicate that IC70BA is an excellent acceptor for the P3HT-based PSCs and could be a promising new acceptor instead of PC70BM for the high performance PSCs based on narrow bandgap conjugated polymer donor. [source]

Origin of Radiation-Induced Degradation in Polymer Solar Cells

ADVANCED FUNCTIONAL MATERIALS, Issue 16 2010
Ankit Kumar
Abstract Polymer solar cells have been shown to degrade under X-rays. Here, in situ polymer photovoltaic performance and recombination lifetimes are measured and it is found that charge accumulation is the primary reason for degradation of solar cells. This is affected by the mixing ratio of donor and acceptor in the bulk heterojunction. Both a quantitative understanding and the physical model of the degradation mechanism are presented. Understanding of the degradation mechanism is extended in polymer donor,acceptor bulk heterojunction systems to propose a material combination for making radiation hard diodes that can find important application in fields ranging from memory arrays to organic X-ray detectors for medical imaging. [source]

Recent Progress in Polymer Solar Cells: Manipulation of Polymer:Fullerene Morphology and the Formation of Efficient Inverted Polymer Solar Cells

ADVANCED MATERIALS, Issue 14-15 2009
Li-Min Chen
Abstract Polymer morphology has proven to be extremely important in determining the optoelectronic properties in polymer-based devices. The understanding and manipulation of polymer morphology has been the focus of electronic and optoelectronic polymer-device research. In this article, recent advances in the understanding and controlling of polymer morphology are reviewed with respect to the solvent selection and various annealing processes. We also review the mixed-solvent effects on the dynamics of film evolution in selected polymer-blend systems, which facilitate the formation of optimal percolation paths and therefore provide a simple approach to improve photovoltaic performance. Recently, the occurrence of vertical phase separation has been found in some polymer:fullerene bulk heterojunctions.1,3 The origin and applications of this inhomogeneous distribution of the polymer donor and fullerene acceptor are addressed. The current status and device physics of the inverted structure solar cells is also reviewed, including the advantage of utilizing the spontaneous vertical phase separation, which provides a promising alternative to the conventional structure for obtaining higher device performance. [source]

High-Yield Synthesis and Electrochemical and Photovoltaic Properties of Indene-C70 Bisadduct

ADVANCED FUNCTIONAL MATERIALS, Issue 19 2010
Youjun He
Abstract [6, 6]-Phenyl-C61 -butyric acid methyl ester (PC60BM) is the widely used acceptor material in polymer solar cells (PSCs). Nevertheless, the low LUMO energy level and weak absorption in visible region are its two weak points. For enhancing the solar light harvest, the soluble C70 derivative PC70BM has been used as acceptor instead of PC60BM in high efficiency PSCs in recent years. But, the LUMO level of PC70BM is the same as that of PC60BM, which is too low for the PSCs based on the polymer donors with higher HOMO level, such as poly (3-hexylthiophene) (P3HT). Here, a new soluble C70 derivative, indene-C70 bisadduct (IC70BA), is synthesized with high yield of 58% by a one-pot reaction of indene and C70 at 180 °C for 72 h. The electrochemical properties and electronic energy levels of the fullerene derivatives are measured by cyclic voltammetry. The LUMO energy level of IC70BA is 0.19 eV higher than that of PC70BM. The PSC based on P3HT with IC70BA as acceptor shows a higher Voc of 0.84 V and higher power conversion efficiency (PCE) of 5.64%, while the PSC based on P3HT/PC60BM and P3HT/PC70BM displays Voc of 0.59 V and 0.58 V, and PCE of 3.55% and 3.96%, respectively, under the illumination of AM1.5G, 100 mW cm,2. The results indicate that IC70BA is an excellent acceptor for the P3HT-based PSCs and could be a promising new acceptor instead of PC70BM for the high performance PSCs based on narrow bandgap conjugated polymer donor. [source]

Polymer Photovoltaics with Alternating Copolymer/Fullerene Blends and Novel Device Architectures

ADVANCED MATERIALS, Issue 20 2010
Olle Inganäs
Abstract The synthesis of novel conjugated polymers, designed for the purpose of photovoltaic energy conversion, and their properties in polymer/fullerene materials and photovoltaic devices are reviewed. Two families of main-chain polymer donors, based on fluorene or phenylene and donor,acceptor,donor comonomers in alternating copolymers, are used to absorb the high-energy parts of the solar spectrum and to give high photovoltages in combinations with fullerene acceptors in devices. These materials are used in alternative photovoltaic device geometries with enhanced light incoupling to collect larger photocurrents or to enable tandem devices and enhance photovoltage. [source]