Home About us Contact
|
Home About us Contact | ||
|
|
||
phenyl-C61-butyric Acid Methyl Ester (phenyl-c61-butyric + acid_methyl_ester)
Selected AbstractsAnnealing-Free High Efficiency and Large Area Polymer Solar Cells Fabricated by a Roller Painting ProcessADVANCED FUNCTIONAL MATERIALS, Issue 14 2010Jae Woong Jung Abstract Polymer solar cells are fabricated by a novel solution coating process, roller painting. The roller-painted film , composed of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) , has a smoother surface than a spin-coated film. Since the roller painting is accompanied by shear and normal stresses and is also a slow drying process, the process effectively induces crystallization of P3HT and PCBM. Both crystalline P3HT and PCBM in the roller-painted active layer contribute to enhanced and balanced charge-carrier mobility. Consequently, the roller-painting process results in a higher power conversion efficiency (PCE) of 4.6%, as compared to that for spin coating (3.9%). Furthermore, annealing-free polymer solar cells (PSCs) with high PCE are fabricated by the roller painting process with the addition of a small amount of octanedi-1,8-thiol. Since the addition of octanedi-1,8-thiol induces phase separation between P3HT and PCBM and the roller-painting process induces crystallization of P3HT and PCBM, a PCE of roller-painted PSCs of up to 3.8% is achieved without post-annealing. A PCE of over 2.7% can also be achieved with 5,cm2 of active area without post-annealing. [source] P3HT/PCBM Bulk Heterojunction Solar Cells: Impact of Blend Composition and 3D Morphology on Device PerformanceADVANCED FUNCTIONAL MATERIALS, Issue 9 2010Svetlana S. van Bavel Abstract The performance of polymer solar cells (PSC) strongly depends on the 3D morphological organization of the donor and acceptor compounds within the bulk heterojunction active layer. The technique of electron tomography is a powerful tool for studying 3D morphology of the layers composed of poly(3-hexylthiophene) (P3HT) and a fullerene derivative ([6,6]-phenyl-C61-butyric acid methyl ester; PCBM), especially to quantify the amount and distribution of fibrillar P3HT nanocrystals throughout the volume of the active layer. In this study, electron tomography is used to characterize P3HT/PCBM layers with different blend compositions, both before and after thermal annealing. The power conversion efficiency of the corresponding PSCs is strongly dependent on the overall crystallinity of P3HT and the way P3HT crystals are distributed throughout the thickness of the active layer. [source] Solution Processable Fluorenyl Hexa- peri -hexabenzocoronenes in Organic Field-Effect Transistors and Solar CellsADVANCED FUNCTIONAL MATERIALS, Issue 6 2010Wallace W. H. Wong Abstract The organization of organic semiconductor molecules in the active layer of organic electronic devices has important consequences to overall device performance. This is due to the fact that molecular organization directly affects charge carrier mobility of the material. Organic field-effect transistor (OFET) performance is driven by high charge carrier mobility while bulk heterojunction (BHJ) solar cells require balanced hole and electron transport. By investigating the properties and device performance of three structural variations of the fluorenyl hexa- peri -hexabenzocoronene (FHBC) material, the importance of molecular organization to device performance was highlighted. It is clear from 1H NMR and 2D wide-angle X-ray scattering (2D WAXS) experiments that the sterically demanding 9,9-dioctylfluorene groups are preventing ,,, intermolecular contact in the hexakis-substituted FHBC 4. For bis-substituted FHBC compounds 5 and 6, ,,, intermolecular contact was observed in solution and hexagonal columnar ordering was observed in solid state. Furthermore, in atomic force microscopy (AFM) experiments, nanoscale phase separation was observed in thin films of FHBC and [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) blends. The differences in molecular and bulk structural features were found to correlate with OFET and BHJ solar cell performance. Poor OFET and BHJ solar cells devices were obtained for FHBC compound 4 while compounds 5 and 6 gave excellent devices. In particular, the field-effect mobility of FHBC 6, deposited by spin-casting, reached 2.8,×,10,3,cm2 V,1 s and a power conversion efficiency of 1.5% was recorded for the BHJ solar cell containing FHBC 6 and PC61BM. [source] Enhanced Thermal Stability and Efficiency of Polymer Bulk-Heterojunction Solar Cells by Low-Temperature Drying of the Active LayerADVANCED FUNCTIONAL MATERIALS, Issue 5 2010Ching Lin Abstract This study addresses two key issues, stability and efficiency, of polymer solar cells based on blended poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) by demonstrating a film-forming process that involves low-temperature drying (,5,°C) and subsequent annealing of the active layer. The low-temperature process achieves 4.70% power conversion efficiency (PCE) and ,1250,h storage half-life at 65,°C, which are significant improvements over the 3.39% PCE and ,143,h half-life of the regular room-temperature process. The improvements are attributed to the enhanced nucleation of P3HT crystallites as well as the minimized separation of the P3HT and PCBM phases at the low drying temperature, which upon post-drying annealing results in a morphology consisting of small PCBM-rich domains interspersed within a densely interconnected P3HT crystal network. This morphology provides ample bulk-heterojunction area for charge generation while allowing for facile charge transport; moreover, the P3HT crystal network serves as an immobile frame at heating temperatures less than the melting point (Tm) of P3HT, thus preventing PCBM/P3HT phase separation and the corresponding device degradation. [source] Effect of Alkyl Side-Chain Length on Photovoltaic Properties of Poly(3-alkylthiophene)/PCBM Bulk HeterojunctionsADVANCED FUNCTIONAL MATERIALS, Issue 20 2009Abay Gadisa Abstract The morphological, bipolar charge-carrier transport, and photovoltaic characteristics of poly(3-alkylthiophene) (P3AT):[6,6]-phenyl-C61-butyric acid methyl ester (PCBM) blends are studied as a function of alkyl side-chain length m, where m equals the number of alkyl carbon atoms. The P3ATs studied are poly(3-butylthiophene) (P3BT, m,=,4), poly(3-pentylthiophene) (P3PT, m,=,5), and poly(3-hexylthiophene) (P3HT, m,=,6). Solar cells with these blends deliver similar order of photo-current yield (exceeding 10,mA cm,2) irrespective of side-chain length. Power conversion efficiencies of 3.2, 4.3, and 4.6% are within reach using solar cells with active layers of P3BT:PCBM (1:0.8), P3PT:PCBM (1:1), and P3HT:PCBM (1:1), respectively. A difference in fill factor values is found to be the main source of efficiency difference. Morphological studies reveal an increase in the degree of phase separation with increasing alkyl chain length. Moreover, while P3PT:PCBM and P3HT:PCBM films have similar hole mobility, measured by hole-only diodes, the hole mobility in P3BT:PCBM lowers by nearly a factor of four. Bipolar measurements made by field-effect transistor showed a decrease in the hole mobility and an increase in the electron mobility with increasing alkyl chain length. Balanced charge transport is only achieved in the P3HT:PCBM blend. This, together with better processing properties, explains the superior properties of P3HT as a solar cell material. P3PT is proved to be a potentially competitive material. The optoelectronic and charge transport properties observed in the different P3AT:PCBM bulk heterojunction (BHJ) blends provide useful information for understanding the physics of BHJ films and the working principles of the corresponding solar cells. [source] A New Supramolecular Route for Using Rod-Coil Block Copolymers in Photovoltaic ApplicationsADVANCED MATERIALS, Issue 6 2010Nicolas Sary A new polymer blend formed by poly(3-hexylthiophene)-poly(4-vinylpyridine) (P3HT- P4VP) block copolymers and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) is reported. The P4VP and PCBM are mixed together by weak supramolecular interactions, and the resulting materials exhibit microphase separated morphologies of electron-donor and electron-acceptor rich domains. The properties of the blend, used in photovoltaic devices as active layers, are also discussed. [source] | ||||||||||