Home About us Contact
|
Home About us Contact | ||
|
|
||
Artificial Bone (artificial + bone)
Selected AbstractsBone Marrow Mesenchymal Stem Cells Form Ectopic Woven Bone In Vivo Through Endochondral Bone FormationARTIFICIAL ORGANS, Issue 4 2009Sophia Chia-Ning Chang Abstract:, Autologous vascularized bone grafts, allografts, and biocompatible artificial bone substitutes each have their shortcomings. Bones regenerated using recombinant human bone morphogenetic proteins, demineralized bone powder, or combinations of these are generally small and do not meet the need. The current trend is to use tissue engineering approaches with bone marrow mesenchymal stem cells (MSCs) to generate bones of a desired size and shape. A suspension of osteogenically induced MSCs (CD11a,, CD29+, CD44+) was added to 2% alginate, gelled by mixing this combination with calcium sulfate (CaSO4 0.2 g/mL), and injected into the subcutaneous pocket in the dorsal aspect of nude mice. Cells of various concentrations (0, 10, 50, and 70 million/mL) were used. These implanted constructs were harvested at predetermined times up to 30 weeks for histology. The doubling time of bovine MSCs is 3.75 ± 1.96 days and the proliferation is rapid. Histological evaluation revealed signs of endochondrosis with woven bone deposition. The equilibrium modulus increased with time in vivo, though less than that of normal tissue. Implants seeded with 70 million cells/mL for 6 months resulted in the best formation of equilibrium modulus. This approach has several advantages: (i) obtaining MSCs is associated with low donor morbidity; (ii) MSCs proliferate rapidly in vitro, and a large number of viable cells can be obtained; and (iii) the MSC/alginate constructs can develop into bone-like nodules with high cell viability. Such a system may be useful in large-scale production of bony implants or in the repair of bony defects. The fact that endochondral bone formation led to woven bone suggests its potential feasibility in regional cell therapy. [source] Influence of surgical technique and surface roughness on the primary stability of an implant in artificial bone with different cortical thickness: a laboratory studyCLINICAL ORAL IMPLANTS RESEARCH, Issue 2 2010Afsheen Tabassum Abstract Objective: The aim of this biomechanical study was to assess the interrelated effect of both surface roughness and surgical technique on the primary stability of dental implants. Material and methods: For the experiment, 160 screw-designed implants (Biocomp®), with either a machined or an etched surface topography, were inserted into polyurethane foam blocks (Sawbones®). As an equivalent of trabecular bone, a density of 0.48 g/cm3 was chosen. To mimic the cortical layer, on top of these blocks short-fibre-filled epoxy sheets were attached with a thickness varying from 0 to 2.5 mm. The implant sites were prepared using either a press-fit or an undersized technique. To measure the primary stability of the implant, both the insertion and the removal torques were scored. Results: Independent of the surgical technique used, both implant types showed an increased insertion and removal torque values with increasing cortical thickness, although >2 mm cortical layer no further increase in insertion torque was observed. In the models with only trabecular bone (without cortical layer) and with a 1 mm cortical layer, both implant types showed a statistically higher insertion and removal torque values for undersized compared with the press-fit technique. In addition, etched implants showed a statistically higher insertion and removal torque mean values compared with machined implants. In the models with 2 and 2.5 mm cortical layers, with respect to the insertion torque values, no effect of either implantation technique or implant surface topography could be observed. Conclusion: The placement of etched implants in synthetic bone models using an undersized preparation technique resulted in enhanced primary implant stability. A correlation was found between the primary stability and the cortical thickness. However, at or above a cortical thickness of 2 mm, the effect of both an undersized surgical approach, as also the presence of a roughened (etched) implant surface, had no extra effect. Besides the mechanical aspects, the biological effect of undersized drilling, i.e. the bone response on the extra insertion torque forces should also be elucidated. Therefore, additional in vivo studies are needed. To cite this article: Tabassum A, Meijer GJ, Wolke JGC, Jansen JA. Influence of surgical technique and surface roughness on the primary stability of an implant in artificial bone with different cortical thickness: a laboratory study. Clin. Oral Impl. Res. 21, 2010; 213,220. doi: 10.1111/j.1600-0501.2009.01823.x [source] Biocompatibility of Lotus-type Stainless Steel and Titanium in Alveolar BoneADVANCED ENGINEERING MATERIALS, Issue 9 2006Y. Higuchi Abstract Lotus-type porous stainless steel (SUS304L) and porous titanium were fabricated by unidirectional solidification in a mixture gas of hydrogen and argon. The porous metals which were cut into 5,mm cubes (non-dehydrogenated) and 3.4,mm,,×,5,mm cylinders (dehydrogenated) were implanted into the canine mandible alveolar bone for two, four and eight weeks for animal experiments. The changes in the tissues were observed using SEM. For porous stainless steel (cylindrical; dehydrogenated) new formation of bones was observed around the sample in two weeks without any sign of bony ingrowth into the pores. The osteogenesis was found in shallow areas in the pores in four weeks and deep in the pores in eight weeks. Porous titanium, on the other hand, showed deep ingrowth of new bones in four weeks. Our observations allowed us to expect application of the porous metals as biomaterials. They maintain mechanical strength and are lighter in weight so that it is expected to be applied for dental implants and core materials of artificial bones. [source] Poly(,-caprolactone)-Functionalized Carbon Nanotubes and Their Biodegradation Properties,ADVANCED FUNCTIONAL MATERIALS, Issue 6 2006H.-L. Zeng Abstract Biodegradable poly(,-caprolactone) (PCL) has been covalently grafted onto the surfaces of multiwalled carbon nanotubes (MWNTs) by the "grafting from" approach based on in-situ ring-opening polymerization of ,-caprolactone. The grafted PCL content can be controlled easily by adjusting the feed ratio of monomer to MWNT-supported macroinitiators (MWNT-OH). The resulting products have been characterized with Fourier-transform IR (FTIR), NMR, and Raman spectroscopies, transmission electron microscopy (TEM), and scanning electron microscopy (SEM). After PCL was coated onto MWNT surfaces, core/shell structures with nanotubes as the "hard" core and the hairy polymer layer as the "soft" shell are formed, especially for MWNTs coated with a high density of polymer chains. Such a polymer shell promises good solubility/dispersibility of the MWNT,PCL nanohybrids in low-boiling-point organic solvents such as chloroform and tetrahydrofuran. Biodegradation experiments have shown that the PCL grafted onto MWNTs can be completely enzymatically degraded within 4,days in a phosphate buffer solution in the presence of pseudomonas (PS) lipase, and the carbon nanotubes retain their tubelike morphologies, as observed by SEM and TEM. The results present possible applications for these biocompatible PCL-functionalized CNTs in bionanomaterials, biomedicine, and artificial bones. [source] | |||||||||||||