			Home About us Contact

Passive Component (passive + component)

Distribution by Scientific Domains

Polymers and Materials Science	50%

Selected Abstracts

Lead Zirconate Titanate Thin Films on Base-Metal Foils: An Approach for Embedded High-Permittivity Passive Components

JOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 10 2001
Jon-Paul Maria
An approach for embedding high-permittivity dielectric thin films into glass epoxy laminate packages has been developed. Lead lanthanum zirconate titanate (Pb0.85La0.15(Zr0.52Ti0.48)0.96O3, PLZT) thin films were prepared using chemical solution deposition on nickel-coated copper foils that were 50 ,m thick. Sputter-deposited nickel top electrodes completed the all-base-metal capacitor stack. After high-temperature nitrogen-gas crystallization anneals, the PLZT composition showed no signs of reduction, whereas the base-metal foils remained flexible. The capacitance density was 300,400 nF/cm2, and the loss tangent was 0.01,0.02 over a frequency range of 1,1000 kHz. These properties represent a potential improvement of 2,3 orders of magnitude over currently available embedded capacitor technologies for polymeric packages. [source]

Silver Surface Iodination for Enhancing the Conductivity of Conductive Composites

ADVANCED FUNCTIONAL MATERIALS, Issue 16 2010
Cheng Yang
Abstract The electrical conductivity of a silver microflake-filled conductive composites is dramatically improved after a filler surface treatment. By a simple iodine solution treatment, nonstoichiometric silver/silver iodide nanoislands form on the silver filler surface. Evidence of the decrease of surface silver oxide species is provided by TOF-SIMS and the redox property of the nanoclusters is studied using cyclic voltammetry and TOF-SIMS depth profile analyses. The redox property of the nanoclusters on silver flakes helps enhance the electrical conductivity of the conductive composites. The electrical resistivity of the improved conductive composites is measured by four-point probe method; the reliability of the printed thin film resistors is evaluated by both the 85 °C/85% relative humidity moisture exposure and the ,40 , 125 °C thermal cycling exposure. The conductive composite printed radio frequency identification (RFID) antennas with 27.5 wt% of the modified silver flake content show comparable performance in the RFID tag read range versus copper foil antennas, and better than those commercial conductive adhesives that require much higher silver content (i.e., 80 wt%). This work suggests that a surface chemistry method can significantly reduce the percolation threshold of the loading level of the silver flakes and improve the electrical conductivity of an important printed electronic passive component. [source]

Silver Surface Iodination for Enhancing the Conductivity of Conductive Composites

A Theoretical Model for the Myogenic Response Based on the Length,Tension Characteristics of Vascular Smooth Muscle

MICROCIRCULATION, Issue 4 2005
BRIAN E. CARLSON
ABSTRACT Objective: A theoretical model is developed to describe the myogenic response of resistance vessels to changes in intravascular pressure, based on a consideration of the active and passive length,tension characteristics of vascular smooth muscle (VSM). The dependence of model parameters on vessel diameter is examined. Methods: The vessel wall is represented mechanically as a nonlinear passive component in parallel with an active contractile component. The level of VSM tone is assumed to have a sigmoidal dependence on circumferential wall tension or stress. Model parameters are optimized for each of 18 independent experimental data sets previously obtained using pressure or wire myograph systems. Results: Close fits between model predictions and experimental data are found in each case. An alternative formulation in which VSM tone depends on circumferential wall stress is found also to be consistent with available data. Significant trends in model parameters as a function of diameter are found. Conclusions: The results support the hypothesis that circumferential tension or stress in the wall provides the signal for myogenic responses. The model provides a basis for simulating steady-state myogenic responses in vascular networks containing a range of vessel diameters. [source]

After-effects of near-threshold stimulation in single human motor axons

THE JOURNAL OF PHYSIOLOGY, Issue 3 2005
Hugh Bostock
Subthreshold electrical stimuli can generate a long-lasting increase in axonal excitability, superficially resembling the phase of superexcitability that follows a conditioning nerve impulse. This phenomenon of ,subthreshold superexcitability' has been investigated in single motor axons in six healthy human subjects, by tracking the excitability changes produced by conditioning stimuli of different amplitudes and waveforms. Near-threshold 1 ms stimuli caused a mean decrease in threshold at 5 ms of 22.1 ± 6.0% (mean ±s.d.) if excitation occurred, or 6.9 ± 2.6% if excitation did not occur. The subthreshold superexcitability was maximal at an interval of about 5 ms, and fell to zero at 30 ms. It appeared to be made up of two components: a passive component linearly related to conditioning stimulus amplitude, and a non-linear active component. The active component appeared when conditioning stimuli exceeded 60% of threshold, and accounted for a maximal threshold decrease of 2.6 ± 1.3%. The passive component was directly proportional to stimulus charge, when conditioning stimulus duration was varied between 0.2 and 2 ms, and could be eliminated by using triphasic stimuli with zero net charge. This change in stimulus waveform had little effect on the active component of subthreshold superexcitability or on the ,suprathreshold superexcitability' that followed excitation. It is concluded that subthreshold superexcitability in human motor axons is mainly due to the passive electrotonic effects of the stimulating current, but this is supplemented by an active component (about 12% of suprathreshold superexcitability), due to a local response of voltage-dependent sodium channels. [source]

Impedimetric detection of covalently attached biomolecules on field-effect transistors

PHYSICA STATUS SOLIDI (A) APPLICATIONS AND MATERIALS SCIENCE, Issue 3 2009
Ranjita GhoshMoulick
Abstract A method for impedimetric detection of biomolecules with field-effect transistor (FET) arrays is presented. For biomolecular detection, the corresponding molecules such as single-stranded DNA or bovine serum albumine (BSA) were covalently immobilized to the gate structure of 16-channel open-gate FET devices. A micro spotter system was used to site-selectively attach biomolecules to selected channels out of the array. The differential transistor transfer function (TTF) of the FETs with attached biomolecules compared to free FETs was recorded. With this impedimetric technique it was possible to reliably detect biomolecules, because the recordings were not disturbed by the typical long-term drift of the sensors like in potentiometric readout mode. For transistor gates, where DNA sequences of different length were attached, small differences in the TTF spectra were detected. When BSA was covalently immobilized to the FETs clear differences in the TTF spectra were detected, which were independent on buffer pH variations around the isoelectric point of the protein. Based on the results presented in this article it can be concluded, that the TTF method detects passive components of the biomolecules like resistance and capacitance rather than surface charge effects. (© 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source]