Home About us Contact
|
Home About us Contact | ||
|
|
||
PVC Sheets (pvc + sheet)
Selected AbstractsA novel route for preparation of PVC sheets with high UV irradiation resistanceJOURNAL OF APPLIED POLYMER SCIENCE, Issue 5 2010Xianke Ye Abstract A novel acrylonitrile acrylate copolymer coating was proposed to improve the UV irradiation resistance of poly(vinyl chloride) (PVC) sheets. Its effect on the photoageing properties of the sheets was evaluated by means of Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), yellowness index test, and the oxygen permeability coefficient and mechanical properties measurement. The experimental results show that the novel acrylonitrile acrylate copolymer coating significantly improves the UV irradiation resistance of PVC sheets. Compared with the PVC sheets without coating, the coated PVC sheets show better mechanical properties, lower yellowness index, and smaller oxygen permeability coefficient after UV irradiation. The analysis on the SEM images of the PVC sheets indicates that the coating acts as a film to prevent the PVC sheets from UV energy and oxygen that can accelerate the photochemical reactions of PVC. The FTIR analysis confirms that the coating can slow down the microstructures development of the PVC sheets, also indicating that the coating impeded the photochemical reactions of PVC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Effects of epoxidized sunflower oil on the mechanical and dynamical analysis of the plasticized poly(vinyl chloride)JOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2008Badra Bouchareb Abstract Epoxidized soybean oil (ESBO), is one of the most commonly used epoxides because of its typical combined roles as a plasticizer and heat stabilizer. In this study, a novel plasticizer of poly(vinyl chloride) (PVC) resins, epoxidized sunflower oil (ESO), was synthesized, and its performance was evaluated. ESO was designed to act as a coplasticizer and a heat stabilizer like ESBO. ESO is used as organic coplasticizer for plasticized PVC containing Ca and Zn stearates as primary stabilizers and stearic acid as lubricant. Di-(2-ethylhexyl) phthalate (DEHP), a conventional plasticizer for PVC, was partially replaced by ESO. Mechanical properties (tensile and shore D hardness) were investigated. The performance of ESO to ESB0 (20 g) for comparison, indicated that ESO could be used as secondary plasticizer for PVC in combination with DEHP. All mechanical and dynamical properties of plasticized PVC sheets varied with the oxirane oxygen of the ESO. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Effects of welding procedures on mechanical and morphological properties of hot gas butt welded PE, PP, and PVC sheetsPOLYMER ENGINEERING & SCIENCE, Issue 4 2008Onur Balkan Mechanical and morphological properties of hot gas butt welds on polyethylene (PE), polypropylene (PP), and polyvinyl chloride (PVC) sheets for four different procedures, which are single and double V-welds with and without a welding shoe, were investigated. Besides, weldabilities of base materials were evaluated by rheological measurements. These revealed that weldabilities of PE and PP sheets were better than that of PVC. Welding energy (Ew), which is transferred onto weld surfaces, was calculated to evaluate weld quality. The results of tensile, impact, and bending tests indicated that the weld strengths of PVC sheets were lower than those of PE and PP sheets. When the welding shoe was used, weld strength increased significantly for each material because of the presence of sufficient welding pressure and the effective heating on surfaces. The best results were attained for the double V-welds with the welding shoe. Morphology of welded regions was evaluated by polarized light, stereo, and scanning electron microscopy. Polarized light microscopy studies indicated that the heat-affected zone (HAZ) consisted of welding rod core, molten zone, and deformed spherulitic zone, and the welding interface was indistinguishable from the base material when the welding pressure was enough. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers [source] | ||||||||||