Home About us Contact
|
Home About us Contact | ||
|
|
||
Microstructural Parameters (microstructural + parameter)
Selected AbstractsA Micromechanical Study of the Deformation Behavior of TRIP-Assisted Multiphase Steels as a Function of the Microstructural Parameters of the Retained AusteniteADVANCED ENGINEERING MATERIALS, Issue 3 2009Denny Tjahjanto The influence of austenitic volume fraction, carbon concentration, and grain size on the behavior of multiphase TRIP steels is investigated by means of micromechanical modeling and finite element simulations. The present analysis allows to directly attribute overall mechanical characteristics to the corresponding microstructural parameters, which is a difficult task to perform experimentally. [source] Inverse Problem for Composites with Imperfect Interface: Determination of Interfacial Thermal Resistance, Thermal Conductivity of Constituents, and Microstructural ParametersJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 4 2000Ce-Wen Nan An explicit method is introduced to solve inverse problems for composites with imperfect interfaces. We apply the method to determine the thermal conductivity of constituents and the interfacial thermal resistance in SiC-particulate-reinforced aluminum-matrix composites and to estimate the whisker thermal conductivity, the interfacial thermal resistance, and the whisker alignment distribution in two types of SiC-whisker-reinforced lithium aluminosilicate glass-ceramic composites from their measured effective thermal conductivity reported in the literature. Certain bounds for these three properties of both SiC-whisker-reinforced glass-ceramic composites are obtained, and reasonable estimates for their exact values from room temperature to 500°C are made. The inverse problem is quite sensitive to noise in the measurements. We also comment on existing estimates. [source] Effects of solidification structure on tear resistance of Al,7% Si,0.4% Mg cast alloysFATIGUE & FRACTURE OF ENGINEERING MATERIALS AND STRUCTURES, Issue 1 2004S.-W. HAN ABSTRACT The tear resistance behaviour of Al,7% Si,0.4% Mg cast alloys was examined using Kahn-type tear test specimens. Tests were performed for two permanent mould casts with an ordinary dendrite structure and a semi-liquid die cast with a globular cell and fine grain structure. The microstructure of the two permanent mould casts was controlled by the cooling rates and the addition of Ti elements. Tear resistance was evaluated by the ,pop-in' stress, the energies required for crack initiation, UEi and the crack propagation, UEp. Special attention was paid to an effective microstructural parameter for tear resistance improvement. Pop-in, indicating sudden crack extension and arrest, was observed in all specimens. Homogeneous deformation occurs near the notch tip of the semi-liquid die cast, characterized by a refined grain structure. Refinement of the grain size is more effective than that of the dendrite cell size or eutectic Si particle size to increase the energy for crack initiation. Unit propagation energy, UEp, can be converted into a critical stress intensity factor, Kc, which in the semi-liquid die cast was improved due to an increased amount of slant or shear fracture surface. [source] A Micromechanical Study of the Deformation Behavior of TRIP-Assisted Multiphase Steels as a Function of the Microstructural Parameters of the Retained AusteniteADVANCED ENGINEERING MATERIALS, Issue 3 2009Denny Tjahjanto The influence of austenitic volume fraction, carbon concentration, and grain size on the behavior of multiphase TRIP steels is investigated by means of micromechanical modeling and finite element simulations. The present analysis allows to directly attribute overall mechanical characteristics to the corresponding microstructural parameters, which is a difficult task to perform experimentally. [source] Quantitative microstructural and texture characterization by X-ray diffraction of polycrystalline ferroelectric thin filmsJOURNAL OF APPLIED CRYSTALLOGRAPHY, Issue 1 2004Jesús Ricote Texture becomes an important issue in ferroelectric materials as it greatly influences the physical properties of polycrystalline films. The use of advanced methods of analysis of the X-ray diffraction profiles, namely quantitative texture analysis or the recently developed combined approach, allows access to quantitative information on the different components of the global texture and to more accurate values of structural and microstructural parameters of both the ferroelectric film and the substrate, not available by more conventional methods of analysis. The results obtained allow important conclusions to be drawn regarding the mechanisms that lead to the development of preferred orientations in thin films and, also, the correlation between them and the ferroelectric behaviour. For example, it is observed that the inducement of a strong ,111, texture component does not mean the complete disappearance of the so-called `natural' ,100,, ,001, components, and that the ratio between the contributions to the global texture of these two components can be changed by the presence of tensile or compressive stress during crystallization of the films. The relative contributions of these texture components are also related to the final properties of the ferroelectric films. [source] Simultaneous refinement of structure and microstructure of layered materialsJOURNAL OF APPLIED CRYSTALLOGRAPHY, Issue 1 2004Matteo Leoni The recursive description of stacking in layered crystals, originally developed by Treacy et al. [Proc. R. Soc. London Ser. A (1991), 433, 499,520] and implemented in the DIFFaX code, is enclosed in a non-linear least-squares minimization routine and combined with additional models (of specimen-related broadening and instrumental broadening) to allow the simultaneous refinement of both structural and microstructural parameters of a layered crystal. This implementation is named DIFFaX+. As examples, the refinements both of a simulated pattern of diamond, showing fault clustering, and of the observed powder pattern of a synthetic stoichiometric nanocrystalline chrysotile are reported. [source] Evaluation of double-crystal SANS data influenced by multiple scatteringJOURNAL OF APPLIED CRYSTALLOGRAPHY, Issue 3-1 2000aroun Evaluation of small-angle neutron scattering (SANS) data is often complicated by multiple scattering effects if large particles of relatively high volume fraction have to be studied and dilution or contrast reduction is impossible. The use of pin-hole SANS instruments is often limited due to the contradictory requirements of high resolution and short wavelength needed to keep scattering contrast as low as possible. Double crystal (DC) SANS diffractometers of Bonse-Hart and bent-crystal type are useful alternatives in such cases, as they permit reaching very high resolution with thermal neutrons. A method for SANS data evaluation suited to DC instruments is presented. It includes the common scheme of the indirect Fourier transformation method, but takes multiple scattering into account. The scattering medium is described by the frequency function g(x) defined as the cosine Fourier transform of slit-smeared data. Although a simplistic model of polydisperse spheres is used to represent g(x), resulting g(x) function and some integral parameters are independent of this model. Tests on simulated data show, that the method reproduce well true values of microstructural parameters, though systematic errors are observed in the cases when the unscattered part of incident beam completely disappears. If the scattering power Abdominal Aortic Calcification, BMD, and Bone Microstructure: A Population-Based Study,JOURNAL OF BONE AND MINERAL RESEARCH, Issue 10 2008John T Chow Abstract To better define the relationship between vascular calcification and bone mass/structure, we assessed abdominal aortic calcification (AAC), BMD, and bone microstructure in an age-stratified, random sample of 693 Rochester, MN, residents. Participants underwent QCT of the spine and hip and high-resolution pQCT (HRpQCT) of the radius to define volumetric BMD (vBMD) and microstructural parameters. AAC was quantified with the Agatston scoring method. In men, AAC correlated with lower vertebral trabecular and femoral neck vBMD (p < 0.001), but not after age or multivariable (age, body mass index, smoking status) adjustment. Separation into <50 and ,50 yr showed this pattern only in the older men. BV/TV and Tb.Th inversely correlated with AAC in all men (p < 0.001), and Tb.Th remained significantly correlated after age adjustment (p < 0.05). Tb.N positively correlated with AAC in younger men (p < 0.001) but negatively correlated in older men (p < 0.001). The opposite was true with Tb.Sp (p = 0.01 and p < 0.001, respectively). Lower Tb.N and higher Tb.Sp correlated with AAC in older men even after multivariable adjustment. Among all women and postmenopausal women, AAC correlated with lower vertebral and femoral neck vBMD (p < 0.001) but not after adjustment. Lower BV/TV and Tb.Th correlated with AAC (p = 0.03 and p = 0.04, respectively) in women, but not after adjustment. Our findings support an age-dependent association between AAC and vBMD. We also found that AAC correlates with specific bone microstructural parameters in older men, suggesting a possible common pathogenesis for vascular calcification and deterioration in bone structure. However, sex-specific differences exist. [source] INFLUENCE OF CELL SIZE AND CELL WALL VOLUME FRACTION ON FAILURE PROPERTIES OF POTATO AND CARROT TISSUEJOURNAL OF TEXTURE STUDIES, Issue 1 2005ARTUR ZDUNEK ABSTRACT This article presents the influence of cell size and cell wall volume fraction on the failure parameters of potato tuber and carrot tissue. Confocal scanning laser microscope was used for obtaining images of the cell structure of the tissues. The mean cell face area and the cell wall volume fraction obtained from the images was compared with work to failure, failure stress, failure strain and secant modulus obtained in a compression test of potato and carrot tissue at two strain rates. Bigger cells and less amount of cell wall material weakened the tissue, which was visible as a linear decrease in the parameters: work to failure, failure stress and failure strain. There were differences between potato and carrot in the secant modulus. For carrot, the secant modulus changed with microstructural parameters, whereas for potato, the secant modulus did not depend on these values. The strain rate decreases all the failure properties for potato. For carrot, only the work to failure was affected by the strain rate. [source] Yodel: A Yield Stress Model for SuspensionsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 4 2006Robert J. Flatt A model for the yield stress of particulate suspensions is presented that incorporates microstructural parameters taking into account volume fraction of solids, particle size, particle size distribution, maximum packing, percolation threshold, and interparticle forces. The model relates the interparticle forces between particles of dissimilar size and the statistical distribution of particle pairs expected for measured or log-normal size distributions. The model is tested on published data of sub-micron ceramic suspensions and represents the measured data very well, over a wide range of volume fractions of solids. The model shows the variation of the yield stress of particulate suspensions to be inversely proportional to the particle diameter. Not all the parameters in the model could be directly evaluated; thus, two were used as adjustable variables: the maximum packing fraction and the minimum interparticle separation distance. The values for these two adjustable variables provided by the model are in good agreement with separate determinations of these parameters. This indicates that the model and the approximations used in its derivation capture the main parameters that influence the yield stress of particulate suspensions and should help us to better predict changes in the rheological properties of complex suspensions. The model predicts the variation of the yield stress of particulate suspensions to be inversely proportional to the particle diameter, but the experimental results do not show a clear dependence on diameter. This result is consistent with previous evaluations, which have shown significant variations in this dependence, and the reasons behind the yield stress dependence on particle size are discussed in the context of the radius of curvature of particles at contact. [source] Effect of Microstructure on the Thermal Conductivity of Hot-Pressed Silicon Nitride MaterialsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 1 2002Angel De Pablos Si3N4 materials with distinct microstructures were prepared by hot-pressing, varying the holding time at the maximum temperature, and using different types and amounts of sintering additives. Materials with thermal conductivities of 15,82 W·(m·K),1 were obtained by changing the processing variables. The highest conductivity was measured for the material with the coarsest microstructure. The effect of microstructural parameters, such as percentage of secondary phases, grain size, and texture on thermal properties of Si3N4 ceramics, were studied. Hot-pressed Si3N4 ceramics were modeled as a two-phase composite made of large grains of high conductivity and a small-grained phase of low conductivity. [source] Grain-Boundary Viscosity of BaO-Doped SiCJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 3 2000Giuseppe Pezzotti Internal friction characterization of the viscosity of a residual SiO2/BaO glass, segregated to grain boundaries of polycrystalline SiC, is presented. The anelastic relaxation peak of internal friction, arising from viscous slip along grain boundaries wetted by a glass phase, is analyzed. Two SiC polycrystals, containing SiO2/BaO glasses with different compositions, are studied and compared with a SiC polycrystal containing only pure SiO2. The internal friction peak is first analyzed with respect to its shift upon frequency change. This analysis allows quantitative assessment of both the intrinsic viscosity and the activation energy for viscous flow of the grain-boundary phase. Both parameters markedly decrease with increasing amounts of BaO dopant, which is consistent with data reported in the literature on SiO2 and SiO2/BaO bulk glasses with the same nominal composition. Analysis of the peak morphology is also attempted, considering the evolution of peak width while varying the grain-boundary glass composition. Moreover, the role of microstructural parameters, such as the distributions of grain size and grain-boundary angles, on the broadening of the internal friction peak is addressed, and a procedure is proposed that allows quantitative evaluation of the activation energy for viscous flow of intergranular glass merely from the width of the internal friction peak. [source]
| | ||||||||||||