Home About us Contact
|
Home About us Contact | ||
|
|
||
Micropores
Terms modified by Micropores Selected AbstractsNanotube Membrane Based BiosensorsELECTROANALYSIS, Issue 1-2 2004Punit Kohli Abstract We review highly sensitive detection based on electrochemical methods. These methods are based on monodisperse gold and alumina nanotubule membranes with inside diameter approaching molecular dimensions. The analyte species can be detected by measuring a change in trans-membrane current when the analyte is added to the nanotubule-based cell. The second method entails the use of a concentration change based on the nanotubule membrane. Biomemtic ion-gated channels micropore and nanotubule membrane sensors are also reviewed. These synthetic ion channels can be switched from an "off" state to an "on" state in response to an external chemical stimulus. Using these methods, we have achieved detection limits as low as 10,pM. Potential applications for these biosensors are in fields such as bioanalytical, biomedical, pharmaceutical and drug discovery. [source] Cracking risk of partially saturated porous media,Part II: Application to drying shrinkageINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 2 2010Bernhard Pichler Abstract Drying of deformable porous media results in their shrinkage, and it may cause cracking provided that shrinkage deformations are hindered by kinematic constraints. Herein, we focus on slow drying of an initially water-saturated sample of a microheterogeneous poroelastic material damaged by parallel mesocracks. The cracking risk is analyzed by means of the thermodynamics-based microporoelasticity model described in the companion paper (Part I), which is extended toward consideration of the hierarchical organization of cracked argillite. Drying of a material sample is studied in a framework where macrodisplacements in direction of the crack normal are blocked, while elsewise macrostress-free boundary conditions prevail. The model implies that the opening/closure behavior of the cracks is governed by an effective pressure, in which the average crack (under)pressure, making the crack opening smaller, competes with the average micropore (under)pressure that makes the crack opening larger. The driving force for crack propagation is a quadratic function of this effective pressure. The model proposes that if drying shrinkage deformations are hindered by kinematic constraints, onset of cracking becomes possible once air entry into the cracks is observed. Copyright © 2009 John Wiley & Sons, Ltd. [source] Porosity and surface characteristics of activated carbons produced from waste tyre rubberJOURNAL OF CHEMICAL TECHNOLOGY & BIOTECHNOLOGY, Issue 1 2002Guillermo San Miguel Abstract Waste tyre rubber has proven to be a suitable precursor for the production of high quality activated carbons. The performance of these carbons in commercial applications such as water treatment or gas purification is highly dependent on their surface characteristics. This paper presents an in-depth investigation on how production conditions may affect the yield and characteristics of activated carbons produced from tyre rubber. For this purpose, three tyre rubbers of different particle sizes were consecutively pyrolysed and then activated in a steam atmosphere at 925,°C using a laboratory-scale rotary furnace. Activation was conducted at different intervals over 80,640,min to achieve different degrees of carbon burn-off. The resulting carbons were analysed for their elemental composition, ash content and nitrogen gas adsorption characteristics. The BET and t -plot models were used to investigate various aspects of their porosity and surface area characteristics. SEM analyses were also conducted for visual examination of the carbon surface. Results show that pyrolytic chars, essentially mesoporous materials, developed a very narrow microporosity during the initial stages of the activation process (up to 15,25,wt% burn-off). Further activation resulted in the progressive enlargement of the average micropore width and a gradual development of the mesoporous structure. Total micropore volumes and BET surface areas increased continuously with the degree of activation to reach values up to 0.498,cm3g,1 and 1070,m2g,1 respectively, while external surface areas developed more rapidly at degrees of activation above 45,wt% burn-off. Results presented in this work also illustrate that carbons produced from powdered rubber developed a narrower and more extensive porosity, both in the micropore and mesopore range, than those produced from rubber of a larger particle size. © 2001 Society of Chemical Industry [source] Tapered element oscillating microbalance (TEOM) studies of isobutane, n-butane and propane sorption in ,- and Y-zeolitesAICHE JOURNAL, Issue 5 2010Kening Gong Abstract A TEOM is used to elucidate the adsorption/desorption characteristics of alkylation reactants on USY- and ,-zeolites. Equilibrium adsorption isotherms were obtained on USY- and ,-zeolites using n-butane, isobutane and propane as proxy reactant molecules (T = 303,398 K, adsorbate partial pressure 0,1.2 bar). Analysis of the transient adsorption/desorption profiles of these molecules from either a bed of the zeolite or pelletized particles of the crystals (with mean size < 1 ,m) demonstrate that diffusion in the secondary meso-/macroporous structure formed in the packing or the pellets controls the overall sorption rates. The experimental adsorption/desorption profiles from the pelletized zeolites were regressed with available mathematical models to obtain effective meso-/macropore diffusivities for reactant molecules, and nearly perfect fits of the experimental and the modeled profiles. Taking into account the dead volume in the system, a criterion for reliable measurements of either micropore or mesopore diffusivities by the TEOM technique is derived. © 2009 American Institute of Chemical Engineers AIChE J, 2010 [source] Theoretical analysis and experimental study on SO2 adsorption onto pistachio-nut-shell activated carbonAICHE JOURNAL, Issue 2 2009Aik Chong Lua Abstract The adsorption study of SO2 onto the activated carbon prepared from pistachio-nut shell was studied theoretically and experimentally. A single-particle sorption model known as concentration-dependent surface diffusivity micropore, surface and macropore diffusion control model incorporating micropore, macropore and surface diffusions, together with a nonlinear isotherm at the micropore mouth, has been derived and solved by a finite difference method. The effects of different types of nonlinear isotherms and concentration dependent surface diffusivities have been thoroughly studied. The effects of adsorbate concentration and temperature on adsorption were studied experimentally. Good agreement was found between the model predictions and the experimental results. The value of the tortuosity factor and the extracted diffusion coefficients obtained are consistent with their corresponding values reported. © 2008 American Institute of Chemical Engineers AIChE J 2009 [source] Encapsulation of silver nanoparticles within micropores of block copolymers constructed by emulsion-induced methodJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 10 2008Koji Ishizu An encapsulation of silver nanoparticles has been developed based on a template technique. Microporous films containing Ag+ ions were constructed by emulsion micelles of PEO- block- PMMA amphiphilic diblock copolymers. Ag+ ions are located around peripheral PEO phases of micropores. Subsequently, Ag nanoparticles (ca. 23 nm in diameter) within the micropore have been prepared by the addition of a chemical reductant, e.g. NaBH4. [source] Multilayer Amorphous-Si-B-C-N/,-Al2O3/,-Al2O3 Membranes for Hydrogen Purification,,ADVANCED ENGINEERING MATERIALS, Issue 6 2010Ravi Mohan Prasad Abstract The hydrogen and carbon monoxide separation is an important step in the hydrogen production process. If H2 can be selectively removed from the product side during hydrogen production in membrane reactors, then it would be possible to achieve complete CO conversion in a single-step under high temperature conditions. In the present work, the multilayer amorphous-Si-B-C-N/,-Al2O3/,-Al2O3 membranes with gradient porosity have been realized and assessed with respect to the thermal stability, geometry of pore space and H2/CO permeance. The ,-Al2O3 support has a bimodal pore-size distribution of about 0.64 and 0.045 µm being macroporous and the intermediate ,-Al2O3 layer,deposited from boehmite colloidal dispersion,has an average pore-size of 8,nm being mesoporous. The results obtained by the N2 -adsorption method indicate a decrease in the volume of micropores,0.35 vs. 0.75,cm3,g,1,and a smaller pore size ,6.8 vs. 7.4 Å,in membranes with the intermediate mesoporous ,-Al2O3 layer if compared to those without. The three times Si-B-C-N coated multilayer membranes show higher H2/CO permselectivities of about 10.5 and the H2 permeance of about 1.05,×,10,8 mol m,2 s,1 Pa,1. If compared to the state of the art of microporous membranes, the multilayer Si-B-C-N/,-Al2O3/,-Al2O3 membranes are appeared to be interesting candidates for hydrogen separation because of their tunable nature and high-temperature and high-pressure stability. [source] Mineral surfaces and soil organic matterEUROPEAN JOURNAL OF SOIL SCIENCE, Issue 2 2003K. Kaiser Summary The organic carbon content of soil is positively related to the specific surface area (SSA), but large amounts of organic matter in soil result in reduced SSA as determined by applying the Brunauer,Emmett,Teller (BET) equation to the adsorption of N2. To elucidate some of the controlling mechanisms of this relation, we determined the SSA and the enthalpy of N2 adsorption of separates with a density > 1.6 g cm,3 from 196 mineral horizons of forest soils before and after removal of organic matter with NaOCl. Likewise, we investigated these characteristics before and after sorption of increasing amounts of organic matter to four mineral soil samples, oxides (amorphous Al(OH)3, gibbsite, ferrihydrite, goethite, haematite), and phyllosilicates (kaolinite, illite). Sorption of organic matter reduced the SSA, depending on the amount sorbed and the type of mineral. The reduction in SSA decreased at larger organic matter loadings. The SSA of the mineral soils was positively related to the content of Fe oxyhydroxides and negatively related to the content of organic C. The strong reduction in SSA at small loadings was due primarily to the decrease in the micropores to which N2 was accessible. This suggests preferential sorption of organic matter at reactive sites in or at the mouths of micropores during the initial sorption and attachment to less reactive sites at increasing loadings. The exponential decrease of the heat of gas adsorption with the surface loading points also to a filling or clogging of micropores at early stages of organic matter accumulation. Desorption induced a small recovery of the total SSA but not of the micropore surface area. Destruction of organic matter increased the SSA of all soil samples. The SSA of the uncovered mineral matrix related strongly to the amounts of Fe oxyhydroxides and the clay. Normalized to C removed, the increase in SSA was small in topsoils and illuvial horizons of Podzols rich in C and large for the subsoils containing little C. This suggests that micropores preferentially associate with organic matter, especially at small loadings. The coverage of the surface of the soil mineral matrix as calculated from the SSA before and after destruction of organic matter was correlated only with depth, and the relation appeared to be linear. We conclude that mineralogy is the primary control of the relation between surface area and sorption of organic matter within same soil compartments (i.e. horizons). But at the scale of complete profiles, the surface accumulation and stabilization of organic matter is additionally determined by its input. [source] Polydisperse Spindle-Shaped ZnO Particles with Their Packing Micropores in the Photoanode for Highly Efficient Quasi-Solid Dye-Sensitized Solar CellsADVANCED FUNCTIONAL MATERIALS, Issue 3 2010Yantao Shi Abstract In this paper, a novel hierarchically structured ZnO photoanode for use in quasi-solid state dye-sensitized solar cells (DSCs) is presented. The film is composed of polydisperse spindle-shaped ZnO particles that are prepared through direct precipitation of zinc acetate in aqueous solution. Without additional pore-forming agents, the microporous structure is well constructed through the packing of polydisperse ZnO particles. In the film, small ZnO particles are able to improve interparticle connectivity and offer a large internal surface area for sufficient dye-adsorption; on the other hand, particles of larger size can enhance the occurrence of light-scattering and introduce micropores for the permeation of quasi-solid state electrolytes. Meanwhile, morphologies, particle size, and specific areas of the products are controlled by altering the reactant concentration and synthetic temperature. Combined with a highly viscous polymer gel electrolyte, a device based on this ZnO photoanode shows high conversion efficiencies, 4.0% and 7.0%, under 100 and 30,mW cm,2 illumination, respectively. Finally, the unsealed device is demonstrated to remain above 90% of its initial conversion efficiency after 7 days, showing excellent stability. [source] Zeolite Catalysts with Tunable Hierarchy Factor by Pore-Growth ModeratorsADVANCED FUNCTIONAL MATERIALS, Issue 24 2009Javier Pérez-Ramírez Abstract The design of hierarchical zeolite catalysts is attempted through the maximization of the hierarchy factor (HF); that is, by enhancing the mesopore surface area without severe penalization of the micropore volume. For this purpose, a novel desilication variant involving NaOH treatment of ZSM-5 in the presence of quaternary ammonium cations is developed. The organic cation (TPA+ or TBA+) acts as a pore-growth moderator in the crystal by OH, -assisted silicon extraction, largely protecting the zeolite crystal during the demetallation process. The protective effect is not seen when using cations that are able to enter the micropores, such as TMA+ Engineering the pore structure at the micro- and mesolevel is essential to optimize transport properties and catalytic performance, as demonstrated in the benzene alkylation with ethylene, a representative mass-transfer limited reaction. The hierarchy factor is an appropriate tool to classify hierarchically structured materials. The latter point is of wide interest to the scientific community as it not only embraces mesoporous zeolites obtained by desilication methods but it also enables to quantitatively compare and correlate various materials obtained by different synthetic methodologies. [source] K-feldspar alteration to gel material and crystallization of glauconitic peloids with berthierine in Cretaceous marine sediments,sedimentary implications (Prebetic Zone, Betic Cordillera, SE Spain)GEOLOGICAL JOURNAL, Issue 1 2008Juan Jiménez-Millán Abstract Glauconitic peloids from a Hauterivian condensed level in a hemipelagic unit of the Internal Prebetic (Los Villares Formation, eastern Betic Cordillera) have been studied by X-ray diffraction (XRD), optical microscopy, scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) and analytical electron microscopy (AEM). The sediments forming the condensed level are characterized by abundant spherical to ovoid green glauconite peloids with radial cracks. Quartz, feldspar and muscovite are also abundant, whereas calcium phosphate is rarely detected. XRD analysis of the peloids reveals glauconite and small amounts of berthierine. SEM and HRTEM data show feldspar dissolution features, a Si,Al-rich gel-like substance filling K-feldspar micropores and interlayering of well-crystallized glauconite and berthierine packets. The last stage of the glauconitization process resulted in conversion of the smectitic precursor. Sedimentary and mineralogical features indicate an autochthonous origin for the glauconite. The depositional environment was a distal, hemipelagic ramp on the Southern Iberian Continental Palaeomargin. Low sedimentation rates lead to sediment condensation in a general transgressive context. The margin was affected by extensional tectonics, creating tilted blocks, resulting in lateral facies changes. The dissolution of K-feldspars probably occurred after their deposition in the marine environment but predating the glauconitization. An influx of meteoric water is therefore required, probably related to subsurface fluxes from adjacent emergent areas (the higher parts of tilted blocks). Copyright © 2007 John Wiley & Sons, Ltd. [source] Multiple Functionalization of Mesoporous Silica in One-Pot: Direct Synthesis of Aluminum-Containing Plugged SBA-15 from Aqueous Nitrate Solutions,ADVANCED FUNCTIONAL MATERIALS, Issue 1 2008Y. Wu Abstract Aluminum-containing plugged mesoporous silica has been successfully prepared in an aqueous solution that contains triblock copolymer templates, nitrates, and silica sources but without using mineral acid. The acidity of the solution can be finely tuned from pH 1.4 to 2.8 according to the amount of the introduced aluminum species which ranged from an Al/Si molar ratio of 0.25/1 to 4.0/1. The aluminum nitrate additive in the starting mixture, along with the weak acidity produced by the nitrates, contributes to the formation of plugged hexagonal structures and the introduction of different amounts of aluminum species into the mesostructure. Characterization by X-ray diffraction, transmission electron microscopy, and N2 sorption measurements show that the Al-containing plugged silicas possess well-ordered hexagonal mesostructures with high surface areas (700,860 m2,g,1), large pore volume (0.77,1.05 cm3,g,1) and, more importantly, combined micropores and/or small mesopores in the cylindrical channels. Inductively coupled plasma,atomic emission spectrometry results show that 0.7,3.0 wt,% aluminum can be introduced into the final samples. 27Al MAS NMR results display that about 43,60% aluminum species are incorporated into the skeleton of the Al-containing silicas and the amount of the framework aluminum increases as the initial added nitrates rises. Scanning electron microscopy images reveal that the directly synthesized Al-containing plugged silica has a similar morphology to that of traditional SBA-15. Furthermore, the Al-containing plugged samples have excellent performances in the adsorption and the catalytic decomposition of isopropyl alcohol and nitrosamine. Finally, the direct synthesis method is used to produce plugged mesoporous silicas that contain other metals such as chromium and copper, and the resultant samples also show good catalytic activities. [source] Preparation, Bioactivity, and Drug Release of Hierarchical Nanoporous Bioactive Glass Ultrathin FibersADVANCED MATERIALS, Issue 6 2010Youliang Hong Hierarchical nanoporous bioactive glass ultrathin fibers with different pore diameters from 1.5-nm micropores up to 65-nm macropores are synthesized using P123,PEO co-templates and an electrospinning technique (see image). Experiments demonstrate that the prepared bioactive glass fibers are highly homogenous and bioactive and their nanopores can control drug release well. [source] Research on Advanced Materials for Li-ion BatteriesADVANCED MATERIALS, Issue 45 2009Hong Li Abstract In order to address power and energy demands of mobile electronics and electric cars, Li-ion technology is urgently being optimized by using alternative materials. This article presents a review of our recent progress dedicated to the anode and cathode materials that have the potential to fulfil the crucial factors of cost, safety, lifetime, durability, power density, and energy density. Nanostructured inorganic compounds have been extensively investigated. Size effects revealed in the storage of lithium through micropores (hard carbon spheres), alloys (Si, SnSb), and conversion reactions (Cr2O3, MnO) are studied. The formation of nano/micro core,shell, dispersed composite, and surface pinning structures can improve their cycling performance. Surface coating on LiCoO2 and LiMn2O4 was found to be an effective way to enhance their thermal and chemical stability and the mechanisms are discussed. Theoretical simulations and experiments on LiFePO4 reveal that alkali metal ions and nitrogen doping into the LiFePO4 lattice are possible approaches to increase its electronic conductivity and does not block transport of lithium ion along the 1D channel. [source] Application of a coil-type TDR probe for measuring the volumetric water content in weathered granitic bedrockHYDROLOGICAL PROCESSES, Issue 6 2008Shin'ya Katsura Abstract As a first step toward describing water flow processes in bedrock, a coil-type time domain reflectometry (TDR) probe capable of measuring volumetric water content, ,, in weathered bedrock at three depths was prepared. Because the coil-type TDR probe is large in diameter (19 mm), it can be installed even in highly weathered bedrock more easily and appropriately than conventional TDR probes that consists of two or three rods of small diameter (5-8 mm). The probe calibrations suggest that the values measured by the probe are very sensitive to changes in ,. Using the calibrated probe together with commercially available profile soil moisture sensors, the , profile was monitored for 1 year. Even rainfall events with relatively small cumulative rainfall of 15 mm increased the bedrock ,, and the increments were comparable to those in the soil. After the end of the rainfall events, the bedrock , displayed a more rapid drop than the soil, and varied little during the period of no rainfall. The water storage showed similar tendencies. These observations suggest that the bedrock , is controlled by clearly distinguishable macropores and micropores within the bedrock. It is concluded that the coil-type TDR probe is very effective in determining , in weathered bedrock, and that bedrock, conventionally defined by conducting cone penetration tests and treated as impermeable, does conduct and hold substantial amounts of water, and therefore contribute greatly to hydrological processes in headwater catchments. Copyright © 2007 John Wiley & Sons, Ltd. [source] Cracking risk of partially saturated porous media,Part I: Microporoelasticity modelINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 2 2010Bernhard Pichler Abstract Drying of deformable porous media results in their shrinkage, and it may cause cracking provided that shrinkage deformations are hindered by kinematic constraints. This is the motivation to develop a thermodynamics-based microporoelasticity model for the assessment of cracking risk in partially saturated porous geomaterials. The study refers to 3D representative volume elements of porous media, including a two-scale double-porosity material with a pore network comprising (at the mesoscale) 3D mesocracks in the form of oblate spheroids, and (at the microscale) spherical micropores of different sizes. Surface tensions prevailing in all interfaces between solid, liquid, and gaseous matters are taken into account. To establish a thermodynamics-based crack propagation criterion for a two-scale double-porosity material, the potential energy of the solid is derived, accounting,in particular,for mesocrack geometry changes (main original contribution) and for effective micropore pressures, which depend (due to surface tensions) on the pore radius. Differentiating the potential energy with respect to crack density parameter yields the thermodynamical driving force for crack propagation, which is shown to be governed by an effective macrostrain. It is found that drying-related stresses in partially saturated mesocracks reduce the cracking risk. The drying-related effective underpressures in spherical micropores, in turn, result in a tensile eigenstress of the matrix in which the mesocracks are embedded. This way, micropores increase the mesocracking risk. Model application to the assessment of cracking risk during drying of argillite is the topic of the companion paper (Part II). Copyright © 2009 John Wiley & Sons, Ltd. [source] Fabric evolution during hydromechanical loading of a compacted siltINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 6 2004Olivier Cuisinier Abstract A study was undertaken on a compacted silt to determine fabric modifications induced by suction and/or stress variations. The link between fabric and hydromechanical behaviour was also investigated. A suction-controlled oedometer, using air overpressure, was developed for this purpose and mercury intrusion porosimetry was employed to determine sample fabric. The initial samples fabric was made of macro and micropores. It was shown that suction increase produced a strong decrease in the macroporosity associated with an increase in microporosity. However, some macropores were not significantly affected by the suction increase; this phenomenon might be related to the initial fabric of the samples. Second, it appears that loading under saturated conditions also produces strong fabric modification: the higher the applied stress, the lower the macroporosity. Soil fabric depends on the maximum stress experienced by the soil. Finally, some tests have shown the influence of suction, as well as the role of the degree of saturation, on the deformation process and the mechanical behaviour. The test results show that in the case of unsaturated mechanical loading, all macropores are not destroyed by the mechanical loading. Copyright © 2004 John Wiley & Sons, Ltd. [source] Platinum Surface Modification of SBA-15 by ,-Radiation Treatment,ADVANCED MATERIALS, Issue 6 2003T. Yamada Modification of the mesoporous surface of SBA-15 with platinum has been successfully carried out by means of ,-radiation treatment. This novel treatment allows the selective growth of platinum in the SBA-15 micropores (see Figure). This is in contrast to traditional temperature treatment, in which platinum particles or rods also grow in the mesopores. [source] Saline Drainage Water, Irrigation Frequency and Crop Species Effects on Some Physical Properties of SoilsJOURNAL OF AGRONOMY AND CROP SCIENCE, Issue 1 2001Y. A. Al-Nabulsi This field study evaluated the effects of water quality, irrigation frequency and crop species on some physical properties of soils. The experiment had a split-split-plot design, with three irrigation water qualities (normal water, drainage water and a 1 : 1 mixture of freshwater and drainage water) as the main treatments, two irrigation frequencies (at 7- and 14-day intervals) as the subtreatments and two crops (barley and alfalfa) as the subsubtreatments. The soil infiltration rate was highest in the barley plot receiving freshwater irrigation at weekly intervals. The lowest soil infiltration rate was found in alfalfa plots receiving saline irrigation water at 14-day intervals. Bulk density and proportions of micropores [pore radius (r) < 1.4 µm] were higher and the proportion of macropores (r > 14.4 µm) was lower in barley than in alfalfa. Saline irrigation caused the greatest decrease in total porosity. The soil infiltration rate was higher with more frequent irrigation, and was highest in alfalfa plots receiving freshwater irrigation. The decrease in soil bulk density and infiltration rate was greater with saline drainage water, irrespective of the crop grown and the irrigation frequency. Salzhaltiges Drainagewasser, Bewässerungshäufig-keit und Kulturpflanzenarten mit Wirkung auf einige physikalische Eigenschaften des Bodens Eine Felduntersuchung wurde vorgenommen, um dem Einfluss der Wasserqualität, der Bewässerungshäufigkeit und Kulturpflanzenarten auf einige physikalische Eigenschaften von Böden zu untersuchen. Die Infiltrationrate mit Frischwasser in wöchentlichen Abständen unter Gerste war hoch. Eine Behandlung mit Salzwasser in 14 tägigen Abständen unter Luzerne zeigte eine geringere Infiltrationsrate des Bodens. Bodendichte und der Anteil der Mikroporen (Poren mit einem Radius von r < 1,4 mm) waren größer und der Anteil der Makroporen (r > 14,4 mm) war unter Gerste geringer. Bewässerung mit Salzwasser verursachte die stärkste Abnahme in der Gesamtporosität. Die Infiltrationsrate des Bodens nahm mit der Häufigkeit der Bewässerung zu und zeigte den höchsten Wert bei Luzerne und einer Frischwasserbewässerung. Die Abnahme in der Bodendichte und der Infiltrationseigenschaften waren bei Salzwasserdrainage unabhängig von der Kulturpflanzenart und der Bewässerungshäufigkeit höher. [source] Biporous polymeric beads fabricated by double emulsification for high-speed protein chromatographyJOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2007Guo-Yong Sun Abstract Rigid biporous beads (BiPB) were fabricated by double emulsification. An aqueous suspension of superfine calcium carbonate granules and organic solvent were used as porogenic agents to create superpores and micropores, respectively. The polymerization of monomers, glycidyl methacrylate, and ethylene glycol dimethacrylate was initiated with benzoin ethyl ether by ultraviolet irradiation. Modified with diethylamine (DEA), the BiPB were derivatized into an anion-exchange medium (which is denoted as DEA,BiPB). The DEA,BiPB with an average diameter of 46.3 ,m was characterized to possess two types of pores, that is, micropores (20,200 nm) and superpores (500,5300 nm). Flow hydrodynamic experiments showed that the DEA,BiPB column had a smaller backpressure than that of the conventional microporous beads column at a given flow rate. The static adsorption capacity of the DEA,BiPB was close to that of the DEA,MiPB for bovine serum albumin. However, frontal analysis demonstrated that the dynamic binding capacity of the DEA,BiPB column was two times higher than that of the DEA,MiPB at a flow rate of 1800 cm/h. Moreover, the purification of the molecular chaperone GroEL was carried out with the DEA,BiPB column at two flow rates (150 and 1500 cm/h). This showed that the GroEL purification was nearly the same at the two flow rates tested. These results indicate that the DEA,BiPB column is promising for high-speed protein chromatography. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 17,23, 2007 [source] Effect of activation temperature on pore development in activated carbon produced from palm shellJOURNAL OF CHEMICAL TECHNOLOGY & BIOTECHNOLOGY, Issue 1 2003Wan Mohd Ashri Wan Daud Abstract A series of experiments were conducted to investigate the effect of activation temperature on pore development of activated carbon produced from palm shell. Activation of the samples was carried out at 800, 850 and 900,°C for different durations ranging from 10 to 180,min. The samples were characterized using N2 adsorption for evaluation of micropores and the mercury intrusion technique for mesopore and macropore analysis. Within the range of activation temperatures studied, high burn-off products derived from high activation temperatures tend to have larger micropore development. However, an increase in the activation temperature has no remarkable effect on mesopore and macropore development. © 2002 Society of Chemical Industry [source] Relevance of Osteoinductive Biomaterials in Critical-Sized Orthotopic DefectJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 5 2006Pamela Habibovic Abstract Several publications have shown the phenomenon of osteoinduction by biomaterials to be real. However, whether the ability of a biomaterial to initiate bone formation in ectopic implantation sites improves the performance of such osteoinductive biomaterial in clinically relevant orthotopic sites remains unclear. No studies have been published in which osteoinductive potential of a biomaterial is directly related to its performance orthotopically. In this study, we compared osteoinductive and nonosteoinductive biphasic calcium,phosphate (BCP) ceramics ectopically and in a clinically relevant critical-sized orthotopic defect in goats. The two materials, BCP1150 and BCP1300, had similar chemical compositions, crystallinities, and macrostructures, but their microstructures differed significantly. BCP1150, sintered at a lower temperature, had a large amount of micropores, small average crystal size, and hence a high specific surface area. In contrast, BCP1300, with few micropores, had a significantly lower specific surface area as compared to BCP1150. Twelve-week intramuscular implantation in goats (n,=,10) showed that bone was induced in all BCP1150 implants, while no signs of bone formation were found in any of the BCP1300 implants. After 12 weeks of implantation in a bilateral critical-sized iliac wing defect in the same goats, BCP1150 showed significantly more bone than BCP1300. In addition, the analysis of fluorochrome markers, which were administered to the animals 4, 6, and 8 weeks after implantation to follow the bone growth dynamics, showed an earlier start of bone formation in BCP1150 as compared to BCP1300. Significantly better performance of an osteoinductive ceramic in a critical-sized orthotopic defect in a large animal model in comparison to a nonosteoinductive ceramic suggests osteoinduction to be clinically relevant. Further improvement of material osteoinductive properties is thus a significant step forward in the search for alternatives for autologous bone graft. © 2006 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res [source] Thermally stable porous supramolecular frameworks based on the metal and ,,, stacking directed self-assembly of 2,6-pyridyldicarboxylic acid bis-4-pyridylamideJOURNAL OF PHYSICAL ORGANIC CHEMISTRY, Issue 8 2003Juan C. Noveron Abstract We report the formation of two thermally stable supramolecular structures based on 2,6-pyridyldicarboxylic acid bis-4-pyridylamide (PyI) and bis(hexafluoroacetylacetonato)manganese(II) that exhibits a microporous structure with cavities bearing hydrogen bonding motifs that can enclathrate acetone and methanol molecules via well-positioned hydrogen bonding interactions. Single-crystal x-ray diffraction in combination with thermogravimetric analysis and X-ray powder diffraction (XRPD) studies were utilized to study the structure and thermal behavior of trans -[Mn(hfacac)2(PyI)2]·2(CH3)2CO (1) and trans -[Mn(hfacac)2(PyI)2]·2CH3OH (2). Our studies indicated that 1 and 2 are isostructural with respect to their supramolecular assembly and trap solvent molecules along the crystallographic b direction via the inwardly directed hydrogen bonding motifs of the PyI component. These solvent molecules can be thermally removed to generate a crystalline material with micropores bearing hydrogen bonding rich sites within an overall supramolecular matrix similar to 1 and 2. The removal of the guest solvent molecules is reversible and can be followed with XRPD. Copyright © 2003 John Wiley & Sons, Ltd. [source] Effects of decreasing soil water content on seminal lateral roots of young maize plantsJOURNAL OF PLANT NUTRITION AND SOIL SCIENCE, Issue 6 2006Abstract Soil micropores that contain water at or below field capacity cannot be invaded by seminal or first-order lateral roots of maize plants because their root diameters are larger than 10 ,m. Hence, at soil-water levels below field capacity plant roots must establish a new pore system by displacement of soil particles in order to access soil water. We investigated how decreasing soil water content (SWC) influences growth and morphology of the root system of young maize plants. Plants were grown in rhizotrons 40,cm wide, 50,cm high, and approximately 0.7,cm thick. Five SWC treatments were established by addition of increasing amounts of water to soil and thorough mixing before filling the rhizotrons. No water was added to treatments 1,4 throughout the experiment. Treatment 5 was watered frequently throughout the experiment to serve as a control. Seminal-root length and SWC in soil layers 0,10, 10,20, 20,30, 30,40, and 40,50,cm were measured at intervals of 2,3 d on scanner images by image analysis. At 15 d after planting, for treatments 1,4 shoot dry weight and total root length were directly related to the amount of water added to the soil, and for treatments 4 and 5, total root length and shoot dry weights were similar. Length of seminal roots visible at the transparent surface of the rhizotron for all treatments was highest in the uppermost soil layer and decreased with distance from the soil surface. For all layers, seminal-root elongation rate was at maximum above a SWC of 0.17,cm3,cm,3, corresponding to a matric potential of ,30 kPa. With decreasing SWC, elongation rate decreased, and 20% of maximum seminal root elongation rate was observed below SWC of 0.05,cm3,cm,3. After destructive harvest for treatment 1,4, number of (root-) tips per unit length of seminal root was found uninfluenced over the range of initial SWC from 0.10 to 0.26,cm3,cm,3. However, initial SWC close to the permanent wilting point strongly increased number of tips. Average root length of first-order lateral (FOL) roots increased as initial SWC increased, and the highest length was found for the frequently watered treatment 5. The results of the study suggest that the ability to produce new FOL roots across a wide range of SWC may give maize an adaptive advantage, because FOL root growth can rapidly adapt to changing soil moisture conditions. [source] Pore-system characteristics of pavement seam materials of urban sitesJOURNAL OF PLANT NUTRITION AND SOIL SCIENCE, Issue 1 2006Thomas Nehls Abstract The original light-brown sandy seam filling of pavements in urban areas turns dark and changes its properties by the time due to various inputs of urban dust. Deposited Corg inputs do mostly not have natural characteristics but are man-made, e.g., diesel dust. Thus, properties of the seam material are not predictable from experiences with forest or agricultural soils. Semiperviously sealed urban areas are sites of contaminant deposition as well as groundwater recharge. For an assessment of the resulting groundwater-contamination risk in these areas, the properties of the seam material, which influences transport processes, must be known. The aim of this study was to investigate the pore-system build-up, which includes size distribution and fractal character in the seam material of urban sites. The investigated samples were taken from pavements adjacent to roads in Berlin and Warsaw. The micropore parameters (nanometer range) were characterized using water-vapor desorption isotherms, mesopore parameters (micrometer range) were estimated from mercury-intrusion porosimetry and macropore parameters (millimeter range) from water-retention curves. Particle density, dry bulk density, and particle-size distribution were measured using standard methods. Volumes of micro- and mesopores as well as particle densities and dry bulk densities correlated with Ctot contents. However, no such relation was found for macropore volumes. Compared to the original sandy seam filling, the altered seam material shows significantly higher Corg contents and higher amounts of micro- and mesopores. Therefore, the available water capacity increases by 0.05,0.11,m3,m,3, as compared to the original sandy seam filling. Compared to natural sandy soils having similar Corg contents, the seam material shows similar macropore volumes, but the volume of mesopores and micropores is a few times smaller. That is mainly because of the particulate character of the organic matter. [source] Encapsulation of silver nanoparticles within micropores of block copolymers constructed by emulsion-induced methodJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 10 2008Koji Ishizu An encapsulation of silver nanoparticles has been developed based on a template technique. Microporous films containing Ag+ ions were constructed by emulsion micelles of PEO- block- PMMA amphiphilic diblock copolymers. Ag+ ions are located around peripheral PEO phases of micropores. Subsequently, Ag nanoparticles (ca. 23 nm in diameter) within the micropore have been prepared by the addition of a chemical reductant, e.g. NaBH4. [source] Solvent-induced self-organization approach for polymeric architectures of micropores, hexagons and spheres based on polyurethanes prepared via novel melt transurethane methodologyJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 12 2007P. Deepa Abstract Solvent-induced self-organization approach was developed, for the first time, to produce polyurethane microporous templates and higher ordered morphologies such as micro or nanometer-sized polymeric hexagons and spheres. A novel melt transurethane methodology was designed and developed for synthesizing new class of cycloaliphatic polyurethanes under nonisocyanate and solvent-free conditions. In this new process, a diurethane monomer was polycondensed with equimolar amounts of diol in presence of Ti(OBu)4 as catalyst with the removal of low boiling alcohol from the equilibrium. The hydrogen bonding of the polyurethanes are very unique to their chemical structure and they undergo selective phase-separation process in solution to produce hexagonally packed microporous templates. The increase of water content in the polymer solution enhances the phase-separation process and the micro pores coalesce to isolate the encapsulated polymer matrix into polymeric hexagons or densely packed solid spheres. The concentration-dependent solution FTIR and 1H NMR of the polyurethanes revealed that the polymers possessing higher H-bonding association constants (K) have greater tendency to undergo solvent-induced self-organization phenomena. The mechanism of solvent-evaporation process indicated that only microporous polyurethanes have tendency to form higher ordered hexagons and spheres whereas others failed to show any new morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2351,2366, 2007 [source] Electrothermal Model Evaluation of Grain Size and Disorder Effects on Pulsed Voltage Response of Microstructured ZnO VaristorsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 4 2008Guogang Zhao Time-dependent, two-dimensional, electrothermal simulations based on random Voronoi networks have been developed to study the internal heating, current distributions and breakdown effects in ZnO varistors in response to high-voltage pulsing. The simulations allow for dynamic predictions of internal failures and to track the progression of hot-spots and thermal stresses. The focus is on internal grain-size variations and relative disorder including micropores. Our results predict that parameters such as the hold-off voltage, internal temperature, and average dissipated energy density would be higher with more uniform grains. This uniformity is also predicted to produce lower thermal stresses and to allow for the application of longer duration pulses. It is shown that the principal failure mechanism arises from internal localized melting, while thermal stresses are well below the thresholds for cracking. Finally, detrimental effects of micropores have been quantified and shown to be in agreement with experimental trends. [source] In vitro and in vivo evaluation of a biodegradable chitosan,PLA composite peripheral nerve guide conduit materialMICROSURGERY, Issue 6 2008Feng Xie M.D., Ph.D. Chitosan, a nature biodegradable material, has good biocompatibility but poor physical properties to serve as a nerve conduit. In this study, polylactic acid (PLA) was added to chitosan to form a composite material with improved intensity and elasticity, to be used as nerve conduits. The chitosan,PLA nerve conduits were fabricated with a mold casting/infrared dehydration technique. The constituent ratio of PLA and chitosan of 1:5 (v:v) was chosen to give the composite material both good mechanical properties and good biocompatibility. An in vitro cytotoxicity test showed that the chitosan,PLA material was not cytotoxic. The conduits were proved biodegradable and had many micropores to allow permeability. We evaluated chitosan,PLA nerve conduits as a guidance channel to repair 10 mm gaps in rat sciatic nerves. Nerve autograft and silicon conduits were used as the control. After 12 weeks, the regenerating nerves in three groups succeeded in passing through the nerve gap and reinnervating the muscle. Assessments, including ECG, histomorphometric evaluation, and weighing of triceps calf muscle, showed that the functional recovery of sciatic nerve was better in chitosan,PLA conduit group than in the silicon conduit group (P < 0.05), but the differences between the chitosan,PLA conduit group and the nerve autograft group were not significant (P > 0.05). Therefore, the chitosan,PLA guide proved to be a promising nerve conduit. © 2008 Wiley-Liss, Inc. Microsurgery, 2008. [source] Modified atmosphere packaging of fresh produce using microporous earthenware materialPACKAGING TECHNOLOGY AND SCIENCE, Issue 5 2006Jung Hyun Yun Abstract Microporous earthenware sheets of 5.5,5.6mm thickness were fabricated with or without a glazing treatment by passing through a sequential firing procedure in a furnace. Their microstructure and gas permeability against oxygen and carbon dioxide were measured and examined for their usability in modified atmosphere packaging of fresh produce. Compared with plastic packaging materials, earthenware sheets with a high proportion of micropores had very high gas permeability and gave CO2:O2 permeability ratios close to 1. Glazing treatment smoothed the surface by clogging the pores on the surface and significantly decreased gas permeability, without affecting the internal microstructure of the earthenware. When the earthenware sheet was combined with a plastic box and used in packaging for strawberries and enoki mushrooms at 5°C, its unique permeability properties developed a modified atmosphere that was beneficial for preserving the quality of the produce. Changes in the earthenware's permeability characteristics due to moisture adsorption and condensation need to be resolved so that the dynamic changes occurring in package atmosphere over time can be better understood. Copyright © 2006 John Wiley & Sons, Ltd. [source] | |||||||||||||||||||||||||||||||||||||