			Home About us Contact

Metal Powder (metal + powder)

Distribution by Scientific Domains

Polymers and Materials Science	50%

Selected Abstracts

ChemInform Abstract: Powder X-Ray Diffraction Study of the Double Complexes [M(NH3)5Cl][M,Cl4] as Precursors of Metal Powders (M: Ir, Rh, Co; M,: Pt, Pd).

CHEMINFORM, Issue 36 2002
Yu. V. Shubin
Abstract ChemInform is a weekly Abstracting Service, delivering concise information at a glance that was extracted from about 100 leading journals. To access a ChemInform Abstract of an article which was published elsewhere, please select a "Full Text" option. The original article is trackable via the "References" option. [source]

Finite element and sensitivity analysis of thermally induced flow instabilities

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS, Issue 10 2010
Jean-Serge Giguère
Abstract This paper presents a finite element algorithm for the simulation of thermo-hydrodynamic instabilities causing manufacturing defects in injection molding of plastic and metal powder. Mold-filling parameters determine the flow pattern during filling, which in turn influences the quality of the final part. Insufficiently, well-controlled operating conditions may generate inhomogeneities, empty spaces or unusable parts. An understanding of the flow behavior will enable manufacturers to reduce or even eliminate defects and improve their competitiveness. This work presents a rigorous study using numerical simulation and sensitivity analysis. The problem is modeled by the Navier,Stokes equations, the energy equation and a generalized Newtonian viscosity model. The solution algorithm is applied to a simple flow in a symmetrical gate geometry. This problem exhibits both symmetrical and non-symmetrical solutions depending on the values taken by flow parameters. Under particular combinations of operating conditions, the flow was stable and symmetric, while some other combinations leading to large thermally induced viscosity gradients produce unstable and asymmetric flow. Based on the numerical results, a stability chart of the flow was established, identifying the boundaries between regions of stable and unstable flow in terms of the Graetz number (ratio of thermal conduction time to the convection time scale) and B, a dimensionless ratio indicating the sensitivity of viscosity to temperature changes. Sensitivities with respect to flow parameters are then computed using the continuous sensitivity equations method. We demonstrate that sensitivities are able to detect the transition between the stable and unstable flow regimes and correctly indicate how parameters should change in order to increase the stability of the flow. Copyright © 2009 John Wiley & Sons, Ltd. [source]

Gel point prediction of metal-filled castor oil-based polyurethanes system,

POLYMERS FOR ADVANCED TECHNOLOGIES, Issue 10-12 2002
Anil Srivastava
Abstract Prediction of gel point conversion and network formation is of great importance in polycondensation during synthesis as well as processing. It enables one to estimate the safe conversions for reactor operation without gelation and the cycle time during processing, and plays an important role in controlling the molding parameters used for reinforced reaction injection molding (RRIM), reaction injection molding (RIM) and compression molding. Theories of gelation have been extensively published in the literature and supported by experimental data for various polycondensation systems. However, most such studies relate to unfilled systems. In this work, metal-filled polyurethanes have been synthesized in bulk by reacting toluene di-isocyanate with castor oil and its polyols possessing different hydroxyl values. Metallic aluminum powder (10,40% by weight) was dispersed thoroughly in castor oil and its polyols before reacting at different temperatures (30,60,°C) in a moisture-free, inert environment. The gel point conversions were measured experimentally and an empirical model from the experimental data has been developed to predict the gelation behavior. The proposed model could be of immense importance in the paints, adhesives and lacquers industries, which use castor oil in bulk. From these experiments it was concluded that: (i) fine metal powder gives a rise in viscosity; (ii) metal fillers not only restrict the molecular motion due to the increase in viscosity, but also lower the conversion; (iii) the vegetable oil and its polyols have a number of bulky groups, which also impart the delay tendency in gel time; (iv) there is a change in gelation dynamics at 50,°C , this is due to the change in reactivity of di-isocyanates; (v) the presence of metal filler does not initiate the intermolecular condensation; (vi) there is a gap between theoretical and experimental gel point owing to the unequal reactivity of the secondary alcohol position; (vii) there is an inverse relationship of gel time with the reaction temperature and hydroxyl value of polyols. An empirical model based on process parameters, i.e., hydroxyl value, temperature, shape factor and filler concentration, has been derived and found to be adequate for the metal-filled system. The correlation coefficient on the data is on the lower side in some cases because the following were not taken into account: (i) the first-order kinetics followed by the reaction in the second half while it is tending towards gelation; (ii) the error in observing the gel point viscosity; (iii) errors in assuming the spherical shape of aluminum metal powder; (iv) errors due to failure to maintain the constant speed in agitation. Copyright © 2003 John Wiley & Sons, Ltd. [source]

Aluminium Foam Sandwich Panels: Manufacture, Metallurgy and Applications

ADVANCED ENGINEERING MATERIALS, Issue 9 2008
J. Banhart
Abstract Sandwich panels consisting of a highly porous aluminium foam core and aluminium alloy face sheets are manufactured by roll-bonding aluminium alloy sheets to a densified mixture of metal powders , usually Al-Si or Al-Si-Cu alloys with 6,8% Si and 3,10% Cu , and titanium hydride, and foaming the resulting three-layer structure by a thermal treatment. We review the various processing steps of aluminium foam sandwich (AFS) and the metallurgical processes during foaming, compare the process to alternative ways to manufacture AFS, e.g. by adhesive bonding, and give an overview of the available literature. Two ways to treat AFS after foaming are presented, namely forging and age-hardening. Some current and potential applications are described and the market potential of AFS is assessed. [source]