Home About us Contact
|
Home About us Contact | ||
|
|
||
Melt Production (melt + production)
Selected AbstractsCrustal structure of central and northern Iceland from analysis of teleseismic receiver functionsGEOPHYSICAL JOURNAL INTERNATIONAL, Issue 1 2000Fiona A. Darbyshire We present results from a teleseismic receiver function study of central and northern Iceland, carried out during the period 1995,1998. Data from eight broad-band seismometers installed in the SIL network operated by the Icelandic Meteorological Office were used for analysis. Receiver functions for each station were generated from events for a wide range of backazimuths and a combination of inversion and forward modelling was used to infer the crustal structure below each station. The models generated show a considerable variation in the nature and thickness of the crust across Iceland. The thinnest crust (20,21 km) is found in the northern half of the Northern Volcanic Zone approximately 120 km north of the centre of the Iceland mantle plume. Thicker crust (24,30 km) is found elsewhere in northern and central Iceland and the thickest crust (37 km) is found close to the plume centre. Velocity,depth profiles show a distinct division of the crust into two main sections, an upper high-velocity-gradient section of thickness 2,8 km and a lower crustal section with small or zero overall velocity gradient. The thickness of the upper crust correlates with the tectonic structure of Iceland; the upper crust is thickest on the flanks of the northern and central volcanic rift zones and thinnest close to active or extinct central volcanoes. Below the Krafla central volcano in northeastern Iceland the receiver function models show a prominent low-velocity zone at 10,15 km depth with minimum shear wave velocities of 2.0,2.5 km s,1. We suggest that this feature results from the presence of partially molten sills in the lower crust. Less prominent low-velocity zones found in other regions of Iceland may arise from locally high temperatures in the crust or from acidic intrusive bodies at depth. A combination of the receiver function results and seismic refraction results constrains the crustal thickness across a large part of Iceland. Melting by passive decompression of the hot mantle below the rift zone in northern Iceland forms a crust of thickness ,20 km. In contrast, the larger crustal thickness below central Iceland probably arises from enhanced melt production due to active upwelling in the plume core. [source] Partial melting of metagreywacke: a calculated mineral equilibria studyJOURNAL OF METAMORPHIC GEOLOGY, Issue 8 2008T. E. JOHNSON Abstract Greywacke occurs in most regionally metamorphosed orogenic terranes, with depositional ages from Archean to recent. It is commonly the dominant siliciclastic rock type, many times more abundant than pelite. Using calculated pseudosections in the Na2O,CaO,K2O,FeO,MgO,Al2O3,SiO2,H2O,TiO2,O system, the partial melting of metagreywacke is investigated using several natural protolith compositions that reflect the main observed compositional variations. At conditions appropriate for regional metamorphism at mid-crustal depths (6,8 kbar), high- T subsolidus assemblages are dominated by quartz, plagioclase and biotite with minor garnet, orthoamphibole, sillimanite, muscovite and/or K-feldspar (±Fe,Ti oxides). Modelled solidus temperatures are dependent on bulk composition and vary from 640 to 690 °C. Assuming minimal melting at the H2O-saturated solidus, initial prograde anatexis at temperatures up to ,800 °C is characterized by very low melt productivity. Significant melt production in commonly occurring (intermediate) metagreywacke compositions is controlled by the breakdown of biotite and production of orthopyroxene (±K-feldspar) across multivariant fields until biotite is exhausted at 850,900 °C. Assuming some melt is retained in the source, then at temperatures beyond that of biotite stability, melt production occurs via the consumption of plagioclase, quartz and any remaining K-feldspar as the melt becomes progressively more Ca-rich and H2O-undersaturated. Melt productivity with increasing temperature across the melting interval in metagreywacke is generally gradational when compared to metapelite, which is characterized by more step-like melt production. Comparison of the calculated phase relations with experimental data shows good consistency once the latter are considered in terms of the variance of the equilibria involved. Calculations on the presumed protolith compositions of residual granulite facies metagreywacke from the Archean Ashuanipi subprovince (Quebec) show good agreement with observed phase relations. The degree of melt production and subsequent melt loss is consistent with the previously inferred petrogenesis based on geochemical mass balance. The results show that, for temperatures above 850 °C, metagreywacke is sufficiently fertile to produce large volumes of melt, the separation from source and ascent of which may result in large-scale crustal differentiation if metagreywacke is abundant. [source] Formation of spinel-cordierite-feldspar-glass coronas after garnet in metapelitic xenoliths: reaction modelling and geodynamic implicationsJOURNAL OF METAMORPHIC GEOLOGY, Issue 3 2007A. M. ÁLVAREZ-VALERO Abstract Spinel + cordierite + K-feldspar + plagioclase + glass form coronas around garnet in metapelitic xenoliths at El Hoyazo and Mazarrón, two localities of the Neogene Volcanic Province (NVP) of SE Spain. The presence of fresh glass (quenched melt) in all phases shows that corona development occurred under partial melting conditions. Algebraic analysis of mass balance in the NCKFMASH system suggests the reaction Grt + Sil + Bt + Pl = Spl + Crd + Kfs + melt as the most plausible model for the development of coronas in the El Hoyazo sample, and indicates that biotite was required as reactant for the formation of cordierite. The P,T conditions for the formation of coronas are estimated at ,820 ± 50 °C, 4.5 ± 0.6 kbar at El Hoyazo, and ,820 ± 50 °C, 4.0 ± 0.4 kbar at Mazarrón. The El Hoyazo xenoliths record a complex P,T history, characterized by early melt production during heating and additional melting during decompression. A local cooling event characterized by minor retrograde reaction and melt crystallization preceded ascent and eruption. This study shows that detailed xenolith analysis may be used to track magma evolution in a chamber. [source] | ||||||||||