Home About us Contact
|
Home About us Contact | ||
|
|
||
Melt Extrusion (melt + extrusion)
Selected AbstractsThermal stability of surfactants with amino and imido groups in poly(ethylene terephthalate)/clay compositesJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2008Xuepei Yuan Abstract Effects of thermal stability of surfactants with amino and imido groups on thermal properties of poly(ethylene terephthalate) (PET)/clay composites were studied. The imidosilane surfactant was synthesized successfully from the imide reaction between amino silane and phthalic anhydride. TGA shows that imidosilane decomposition behaviors have two major stages according to the degradations of different functional groups. After melt extrusion, the decomposition of amino functional groups in amino surfactants decreases the thermal stability of organoclay and accelerates the degradation behaviors of PET composites. Because of the enhanced thermal stability of imidosilane surfactants, PET/imido-palygorskite (PT) composites represent enhanced thermal stability, good dispersion and low thermal expansion. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Miscibility and rheological properties of poly(vinyl chloride)/styrene,acrylonitrile blends prepared by melt extrusionJOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2007Hyun Sik Moon Abstract Styrene,acrylonitrile (SAN) with acrylonitrile (AN) concentrations of 11.6,26 wt % and ,-methylstyrene acrylonitrile (,MSAN) with a wide range of AN concentrations are miscible with poly(vinyl chloride) (PVC) through solution blending. Here we examine the rheological properties and miscibility of PVC/SAN and PVC/,MSAN blends prepared by melt extrusion for commercial applications. We have investigated the rheological properties of the blends with a rheometer and a melt indexer. The PVC/SAN and PVC/,MSAN blends have a low melting torque, a long degradation time, and a high melt index, and this means that they have better processability than pure PVC. The miscibility of the blends has been characterized with differential scanning calorimetry, dynamic mechanical thermal analysis, and advanced rheometrics expansion system analysis. The miscibility of the blends has also been characterized with scanning electron microscopy. The SAN series with AN concentrations of 24,31 wt % is immiscible with PVC by melt extrusion, whereas ,MSAN with 31 wt % AN is miscible with PVC, even when they are blended by melt extrusion, because of the strong interaction between PVC and ,MSAN. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007 [source] The use of three different solid dispersion formulations,melt extrusion, film-coated beads, and a glass thermoplastic system,to improve the bioavailability of a novel microsomal triglyceride transfer protein inhibitorJOURNAL OF PHARMACEUTICAL SCIENCES, Issue 5 2004Geert Verreck Abstract A bioavailable formulation for a water-insoluble microsomal triglyceride transfer protein inhibitor, R103757, was developed using solid dispersion technology. The need for an advanced formulation was tested in the dog by assessing the oral bioavailability of three generic concepts: a tablet (crystalline drug), a capsule (film-coated beads), and an oral solution. These screening studies steered further development in the direction of a solid dispersion. Three solid dispersion platforms were assessed: melt extrusion, film-coated beads, and a glass thermoplastic system. Thermal and spectrophotometric analysis revealed that no crystalline drug was present in any of the formulations. The dissolution profiles of the three dispersion systems showed that release was improved compared with the unmanipulated drug. In addition, stability studies confirmed the physical and chemical integrity of the formulation. A human clinical trial was performed to assess the pharmacokinetics of the three amorphous dispersions. Plasma levels were obtained after single oral administration in both the fasting and fed state. The study indicated that all three approaches improved the bioavailability of R103757 with the glass thermoplastic system providing the best performance. These studies point to the potential usefulness of solid dispersion approaches and expand the possible number of ways to implement these methodologies. © 2004 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 93:1217,1228, 2004 [source] Characterization of glass solutions of poorly water-soluble drugs produced by melt extrusion with hydrophilic amorphous polymersJOURNAL OF PHARMACY AND PHARMACOLOGY: AN INTERNATI ONAL JOURNAL OF PHARMACEUTICAL SCIENCE, Issue 3 2001Angus Forster Indomethacin, lacidipine, nifedipine and tolbutamide are poorly soluble in water and may show dissolution-related low oral bioavailability. This study describes the formulation and characterization of these drugs as glass solutions with the amorphous polymers polyvinylpyrrolidone (PVP) and polyvinylpyrrolidone-co-vinyl acetate by melt extrusion. The extrudates were compared with physical mixtures of drug and polymer. X-ray powder diffraction, thermal analysis, infrared spectroscopy, scanning electron microscopy, HPLC, moisture analysis and dissolution were used to examine the physicochemical properties and chemical stability of the glass solutions prepared by melt extrusion at a 1:1 drug/polymer ratio. Depending on the temperature used, melt extrusion produced amorphous glass solutions, with markedly improved dissolution rates compared with crystalline drug. A significant physicochemical interaction between drug and polymer was found for all extrudates. This interaction was caused by hydrogen bonding (H-bonding) between the carbonyl group of the pyrrole ring of the polymer and a H-donor group of the drug. Indomethacin also showed evidence of H-bonding when physical mixtures of amorphous drug and PVP were prepared. After storage of the extrudates for 4,8 weeks at 25°C/75% relative humidity (RH) only indomethacin/polymer (1:1) extrudate remained totally amorphous. All extrudates remained amorphous when stored at 25°C/< 10% RH. Differences in the physical stability of drug/polymer extrudates may be due to differences in H-bonding between the components. [source] Functionalized Graphenes and Thermoplastic Nanocomposites Based upon Expanded Graphite OxideMACROMOLECULAR RAPID COMMUNICATIONS, Issue 4-5 2009Peter Steurer Abstract Exfoliation of expanded GO represents an attractive route to functionalized graphenes as versatile 2D carbon nanomaterials and components of a wide variety of polymer nanocomposites. Thermally reduced graphite oxides (TrGO) with specific surface areas of 600 to 950 m2,·,g,1 were obtained by oxidation of graphite followed by thermal expansion at 600,°C. Thermal post treatment at 700,°C and 1,000,°C increased carbon content (81 to 97 wt.-%) and lowered resistivity (1,600 to 50 ,,·,cm). During melt extrusion with PC, iPP, SAN and PA6, exfoliation afforded uniformly dispersed graphenes with aspect ratio,>,200. In comparison to conventional 0D and 1D carbon nanoparticles, TrGO afforded nanocomposites with improved stiffness and lower percolation threshold. Recent progress and new strategies in development of functionalized graphenes and graphene-based nanocomposites are highlighted. [source] Morphology and mechanical properties of impact modified polypropylene blendsPOLYMER ENGINEERING & SCIENCE, Issue 11 2008Nathan Tortorella Isotactic polypropylene (PP) has been reactively blended with various grades of an ethylene,octene copolymer (EOC) in a twin-screw extruder. Free radical polymerization of styrene and a multifunctional acrylate during melt extrusion has resulted in an enhancement of mechanical properties over the binary blend. The reactive blend exhibits a notched Izod impact strength over 12 times that of pure polypropylene and greater than double the performance of the binary blend. Electron microscopy shows that by grafting onto the polymers, elastomer particle size and interparticle distance decrease, while particle shape becomes less spherical. The acrylate is crucial to achieve superior performance, as infrared spectra correlate an increase in graft yield to improvements in stress,strain behavior and impact strength. In addition, melt flow index (MFI) and melt strength data indicate a reduction in unwanted side reactions of polypropylene and the presence of long-chain branching. Dynamic-mechanical analysis reveals that the reaction promotes miscibility between polypropylene and the EOC and reduces molecular mobility at their glass-transition temperatures. Mechanical properties, graft yield, and MFI are shown to be highly dependent upon the elastomer's concentration, density, and molecular weight, initiator and monomer concentration, as well as processing temperature. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers [source] | ||||||||||