Home About us Contact
|
Home About us Contact | ||
|
|
||
Mechanical Testing (mechanical + testing)
Selected AbstractsIn situ Mechanical Testing Reveals Periodic Buckle Nucleation and Propagation in Carbon Nanotube BundlesADVANCED FUNCTIONAL MATERIALS, Issue 14 2010Shelby B. Hutchens Abstract Uniaxial compression studies are performed on 50-µm-diameter bundles of nominally vertical, intertwined carbon nanotubes grown via chemical vapor deposition from a photolithographically defined catalyst. The inhomogeneous microstructure is examined, demonstrating density and tube orientation gradients, believed to play a role in the unique periodic buckling deformation mechanism. Through in situ uniaxial compression experiments it is discovered that the characteristic bottom-to-top sequential buckling proceeds by first nucleating on the bundle surface and subsequently propagating laterally through the bundle, gradually collapsing the entire structure. The effects of strain rate are explored, and storage and loss stiffnesses are analyzed in the context of energy dissipation. [source] Mechanical testing of fixation techniques for scaffold-based tissue-engineered graftsJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2008Sven Kili No abstract is available for this article. [source] Targeted Deletion of the Sclerostin Gene in Mice Results in Increased Bone Formation and Bone Strength,,JOURNAL OF BONE AND MINERAL RESEARCH, Issue 6 2008Xiaodong Li Abstract Introduction: Sclerosteosis is a rare high bone mass genetic disorder in humans caused by inactivating mutations in SOST, the gene encoding sclerostin. Based on these data, sclerostin has emerged as a key negative regulator of bone mass. We generated SOST knockout (KO) mice to gain a more detailed understanding of the effects of sclerostin deficiency on bone. Materials and Methods: Gene targeting was used to inactivate SOST and generate a line of SOST KO mice. Radiography, densitometry, ,CT, histomorphometry, and mechanical testing were used to characterize the impact of sclerostin deficiency on bone in male and female mice. Comparisons were made between same sex KO and wildtype (WT) mice. Results: The results for male and female SOST KO mice were similar, with differences only in the magnitude of some effects. SOST KO mice had increased radiodensity throughout the skeleton, with general skeletal morphology being normal in appearance. DXA analysis of lumbar vertebrae and whole leg showed that there was a significant increase in BMD (>50%) at both sites. ,CT analysis of femur showed that bone volume was significantly increased in both the trabecular and cortical compartments. Histomorphometry of trabecular bone revealed a significant increase in osteoblast surface and no significant change in osteoclast surface in SOST KO mice. The bone formation rate in SOST KO mice was significantly increased for trabecular bone (>9-fold) at the distal femur, as well as for the endocortical and periosteal surfaces of the femur midshaft. Mechanical testing of lumbar vertebrae and femur showed that bone strength was significantly increased at both sites in SOST KO mice. Conclusions:SOST KO mice have a high bone mass phenotype characterized by marked increases in BMD, bone volume, bone formation, and bone strength. These results show that sclerostin is a key negative regulator of a powerful, evolutionarily conserved bone formation pathway that acts on both trabecular and cortical bone. [source] Multilayer tendon slices seeded with bone marrow stromal cells: A novel composite for tendon engineeringJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 7 2009Hiromichi Omae Abstract The ideal scaffold for tendon engineering would possess the basic structure of the tendon, native extracellular matrix, and capability of cell seeding. The purpose of this study was to assess the tissue engineering potential of a novel composite consisting of a decellularized multilayer sliced tendon (MST) scaffold seeded with bone marrow stromal cells (BMSC). BMSC and infraspinatus tendons were harvested from 20 dogs. The tendons were sectioned in longitudinal slices with a thickness of 50 µm. The slices were decellularized, seeded with BMSC, and then bundled into one composite. The composite was incubated in culture media for 14 days. The resulting BMSC-seeded MST was evaluated by qRT-PCR and histology. The BMSC viability was assessed by a fluorescent tracking marker. Histology showed that the seeded cells aligned between the collagen fibers of the tendon slices. Analysis by qRT-PCR showed higher tenomodulin and MMP13 expression and lower collagen type I expression in the composite than in the BMSC before seeding. BMSC labeled with fluorescent tracking marker were observed in the composite after culture. Mechanical testing showed no differences between scaffolds with or without BMSC. BMSC can survive in a MST scaffold. The increased tenomodulin expression suggests that BMSC might express a tendon phenotype in this environment. This new composite might be useful as a model of tendon tissue engineering. © 2008 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 27: 937,942, 2009 [source] Covalently-linked hyaluronan promotes bone formation around Ti implants in a rabbit modelJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 5 2009Marco Morra Abstract The goal of this study was the in vivo evaluation of nanoporous titanium (Ti) implants bearing a covalently linked surface hyaluronan (HA) layer. Implant surface topography and surface chemistry were previously evaluated by scanning electron micorscopy and X-ray photoelectron spectroscopy. Results showed that the surface modification process did not affect surface topography, yielding a homogeneously HA-coated nanotextured implant surface. In vivo evaluation of implants in both cortical and trabecular bone of rabbit femurs showed a significant improvement of both bone-to-implant contact and bone ingrowth at HA-bearing implant interfaces at 4 weeks. The improvement in osteointegration rate was particularly evident in the marrow-rich trabecular bone (bone-to-implant contact: control 22.5%; HA-coated 69.0%, p,<,0.01). Mechanical testing (push-out test) and evaluation of interfacial bone microhardness confirmed a faster bone maturation around HA-coated implants (Bone Maturation Index: control 79.1%; HA-coated 90.6%, p,<,0.05). Suggestions based on the biochemical role of HA are presented to account for the observed behavior. Published by Wiley Periodicals, Inc. J Orthop Res 27: 657,663, 2009 [source] Evaluation of articular cartilage repair using biodegradable nanofibrous scaffolds in a swine model: a pilot studyJOURNAL OF TISSUE ENGINEERING AND REGENERATIVE MEDICINE, Issue 1 2009Wan-Ju Li Abstract The aim of this study was to evaluate a cell-seeded nanofibrous scaffold for cartilage repair in vivo. We used a biodegradable poly(,-caprolactone) (PCL) nanofibrous scaffold seeded with allogeneic chondrocytes or xenogeneic human mesenchymal stem cells (MSCs), or acellular PCL scaffolds, with no implant as a control to repair iatrogenic, 7 mm full-thickness cartilage defects in a swine model. Six months after implantation, MSC-seeded constructs showed the most complete repair in the defects compared to other groups. Macroscopically, the MSC-seeded constructs regenerated hyaline cartilage-like tissue and restored a smooth cartilage surface, while the chondrocyte-seeded constructs produced mostly fibrocartilage-like tissue with a discontinuous superficial cartilage contour. Incomplete repair containing fibrocartilage or fibrous tissue was found in the acellular constructs and the no-implant control group. Quantitative histological evaluation showed overall higher scores for the chondrocyte- and MSC-seeded constructs than the acellular construct and the no-implant groups. Mechanical testing showed the highest equilibrium compressive stress of 1.5 MPa in the regenerated cartilage produced by the MSC-seeded constructs, compared to 1.2 MPa in the chondrocyte-seeded constructs, 1.0 MPa in the acellular constructs and 0.2 MPa in the no-implant group. No evidence of immune reaction to the allogeneically- and xenogeneically-derived regenerated cartilage was observed, possibly related to the immunosuppressive activities of MSCs, suggesting the feasibility of allogeneic or xenogeneic transplantation of MSCs for cell-based therapy. Taken together, our results showed that biodegradable nanofibrous scaffolds seeded with MSCs effectively repair cartilage defects in vivo, and that the current approach is promising for cartilage repair. Copyright © 2008 John Wiley & Sons, Ltd. [source] Reactive extrusion of poly(ethylene terephthalate),(ethylene/methyl acrylate/glycidyl methacrylate),organoclay nanocompositesPOLYMER COMPOSITES, Issue 2 2007Elif Alyamac This study was conducted to investigate the effects of component concentrations and addition order of the components on the final properties of ternary nanocomposites composed of poly(ethylene terephthalate), organoclay, and an ethylene,methyl acrylate,glycidyl methacrylate (E-MA-GMA) terpolymer acting as an impact modifier for PET. In this context, first, the optimum amount of the impact modifier was determined by melt compounding binary PET-terpolymer blends in a corotating twin-screw extruder. The amount of the impact modifier (5 wt%) resulting in the highest Young's modulus and moderate elongation at break was selected owing to its balanced mechanical properties. Thereafter, by using 5 wt% terpolymer content, the effects of organically modified clay concentration and addition order of the components on the properties of ternary nanocomposites were systematically investigated. Mechanical testing revealed that different addition orders of the materials significantly affected the mechanical properties. Among the investigated addition orders, the best sequence of component addition (PI-C) was the one in which poly(ethylene terephthalate) was first compounded with E-MA-GMA. Later, this mixture was compounded with the organoclay in the subsequent run. In X-ray diffraction analysis, extensive layer separation associated with delamination of the original clay structure occurred in PI-C and CI-P (Clay + Impact Modifier followed by PET) sequences with both 1 and 3 wt% clay contents. X-ray diffraction patterns showed that at these conditions exfoliated structures resulted as indicated by the disappearance of any peaks due to the diffraction within the consecutive clay layers. POLYM. COMPOS., 28:251,258, 2007. © Society of Plastic Engineers [source] Mechanical and viscoelastic properties of semi-interpenetrating polymer networks of poly(vinyl chloride)/thermosetting resin blendsPOLYMER ENGINEERING & SCIENCE, Issue 6 2000Charles U. Pittman Jr. Semi-interpenetrating polymer networks (SIPNs) of PVC/thermoset were prepared by premixing porous, 150 ,m diameter particles of PVC and a small quantity (from 5 to 15% by weight) of a single thermosetting liquid preresin from one of five types (e.g. methylene bis-phenyl diisocyanate (MDI), oligomeric MDI isocyanates (PAPI), toluene diisocyanate (TDI) prepolymer, epoxy, and vinyl ester resins, respectively). Two roll milling of these mixtures was followed by hot-press curing. Mechanical testing indicated that most of these blends exhibited increased tensile, impact, and flexural strengths. The strength increments were greater when going from 0 to 5% thermoset content than when going from 5 to 10% or 10 to 15% thermoset. In many cases, increasing thermoset content from 10 to 15% gave slightly decreased or unchanged tensile, impact, and flexural strengths. This behavior is in accord with a "thermoset dilution effect" in PVC. Most of these SIPN blends exhibited a tan , peak temperature lower than that for pure PVC in the glass transition region. The tan , peak temperatures were progressively lowered as the amounts of thermoset increased. Also, a single distinct peak existed in the E, curves for most of the blends. Only the PVC/epoxy (90/10) blend showed two peak maxima in E, vs. temperature curves. All blends exhibited peak E, values at a lower temperature than those of PVC which had been exposed to the same processing temperatures. These observations seem to rule out the presence of large domains of PVC, which are phase-separated from PVC/thermoset SIPN, and pure thermoset domains. A substantial amount of the added thermoset appears to exist in SIPN type phases in these five blend types. [source] Nano-Scale Design of TiAl Alloys Based on ,-Phase Decomposition,ADVANCED ENGINEERING MATERIALS, Issue 5 2006F. Appel Abstract Phase decomposition and ordering reactions in ,/B2-phase containing TiAl alloys were utilized to establish a novel, previously unreported, type of laminate microstructure. The characteristic constituent of this microstructure are laths with a nanometer-scale substructure that are comprised of several stable and metastable phases. Microstructural control can be achieved by conventional thermomechanical processing and leads to a structurally and chemically very homogeneous material with excellent mechanical properties. The physical metallurgy of this novel type of alloy has been assessed by transmission electron microscope investigations and mechanical testing. [source] Effects of two different maleic anhydride-modified adhesion promoters (PP-g-MA) on the structure and mechanical properties of nanofilled polyolefinsJOURNAL OF APPLIED POLYMER SCIENCE, Issue 2 2009P. Eteläaho Abstract The effects of adhesion promoter properties on the structure and mechanical behavior of nanoclay-filled polyolefin nanocomposites are presented. Two different maleic anhydride-modified polypropylenes having varying maleic anhydride content and molecular weight were used. The influence of these parameters on the performance and morphology of the prepared polypropylene and high density polyethylene-based nanocomposites was examined by mechanical testing, X-ray diffraction, and electron microscopy. The low molecular weight adhesion promoter seemed to be effective in both matrices in relation to mechanical property enhancements, whereas its high molecular weight counterpart performed well only in polyethylene matrix. X-ray diffraction results and examination of morphology revealed that the intercalation and the dispersion of the nanoclay were more even in both matrices when the low molecular weight adhesion promoter with a higher maleic anhydride content was used. On the other hand, the use of high molecular weight adhesion promoter led to a less uniform dispersion but also to a greater amount of exfoliated clay particles. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009 [source] Compressive response and energy absorption of foam EPDMJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2007Biqin Wang Abstract Ethylene,propylene,diene terpolymer foam was prepared by two different processing routes. The microstructure and mechanical properties of the foams with wide relative density ranging from 0.11 to 0.62 have been studied via scanning electron microscopy and mechanical testing, respectively. Scanning electron microscopy shows that the foam with lower relative density has a unique bimodal cell size structure, which the larger cells inlay among the smaller cells, while the foam articles with higher relative density have thicker cell walls with few small cells. The compressive stress,strain curves show that the foam articles with lower relative density have three regimes: linear elastic, a wide slightly rising plateau, and densification, while the foam articles with higher relative density have only two regimes: the longer linear elastic and densification. The relative modulus increases with the increase in the relative density. The contribution of the gas trapped in the cell to the modulus could be neglected. The energy absorbed per unit volume is relationship with the permitted stress and the relative density. The efficiency and the ideality parameter were evaluated from the compressive stress,strain plots. The parameters were plotted against stress to obtain maximum efficiency and the maximum ideality region, which can be used for optimizing the choice for practical applications in cushioning and packaging. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007 [source] Development, characterization, and validation of porous carbonated hydroxyapatite bone cementJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 2 2009Pei-Fu Tang Abstract Carbonated hydroxyapatite (CHA) bone cement is capable of self-setting and forming structures similar to mineralized bone. Conventional CHA leaves little room for new bone formation and delays remodeling. The purposes of this study were to develop porous CHA (PCHA) bone cement and to investigate its physicochemical properties, biocompatibility, biodegradation, and in vivo bone repair potential. Vesicants were added to modify CHA, and the solidification time, porosity, and pore size of the PCHA cements were examined. The cytotoxicity and bone repair potential of PCHA were tested in a rabbit bone defect model and assessed by x-ray, histological examination, and mechanical testing. The porosity of the modified PCHA was 36%; 90.23% of the pores were greater than 70 ,m, with a calcium/phosphate ratio of 1.64 and a solidification time of 15 minutes. The PCHA did not affect bone cell growth in vitro, and the degrading time of the PCHA was two and four times faster in vitro and in vivo when compared to CHA. In the bone defect model, the amount of new bone formation in the PCHA-treated group was eight times greater than that of the CHA group; the compressive strength of the PCHA setting was relatively weak in the first weeks but increased significantly at 8 to 16 weeks compared to the CHA group. The PCHA has stable physicochemical properties and excellent biocompatibility; it degrades faster than CHA, provides more porous spaces for new bone ingrowths, and may be a new form of bone cement for the management of bone defects. © 2009 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 2009 [source] Analysis of a retrieved Isola spinal system fractured in serviceJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2003E. A. Magnissalis Abstract A 1/4-in.diameter two-column Isola spinal system implanted in a 13-year-old girl suffering from cerebral palsy and a severe neuromuscular scoliosis of 120°, was replaced 22 months after primary implantation. The system was removed due to fracture of the lower left (concave) bar, between its two cross connectors (i.e., the distal bypass connector and a transverse cross link), as a result of a postoperative infection and a subsequently developed pseudarthrosis. The retrieved implants were analyzed with the use of a multitechnique characterization procedure involving macroscopic and microscopic examination, micro-multiple internal reflectance FTIR spectroscopy, X-ray fluorescence (XRF) spectrometry, roughness measurement, and mechanical testing of the constituent material and components. Findings suggest that the spinal system failed due to in vivo loosening of a two-set screw tandem connector and subsequent overloading of the contralateral bar. © 2002 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 64B: 6,12, 2003 [source] Recovery of Trabecular and Cortical Bone Turnover After Discontinuation of Risedronate and Alendronate Therapy in Ovariectomized RatsJOURNAL OF BONE AND MINERAL RESEARCH, Issue 10 2008Robyn K Fuchs Abstract Alendronate (ALN) and risedronate (RIS) are bisphosphonates effective in reducing bone loss and fractures associated with postmenopausal osteoporosis. However, it is uncertain how long it takes bone turnover to be re-established after treatment withdrawal, and whether this differs between the two drugs. The objective of this study was to determine the time required to re-establish normal bone turnover after the discontinuation of ALN and RIS treatment in an animal model of estrogen-deficiency osteoporosis. Two hundred ten, 6-mo-old female Sprague-Dawley rats were ovariectomized and 6 wk later were randomized into baseline controls (n = 10) and four treatment groups (n = 50/group): vehicle-treated controls (CON; 0.3 ml sterile water), ALN (2.4 ,g/kg), low-dose RIS (RIS low; 1.2 ,g/kg), and high-dose RIS (RIS high; 2.4 ,g/kg). Treatments were administered 3 times/wk by subcutaneous injection. Baseline controls were killed at the initiation of treatment. Other groups were treated for 8 wk, and subgroups (n = 10/ treatment group) were killed 0, 4, 8, 12, and 16 wk after treatment was withdrawn. Static and dynamic histological analyses were performed for cortical (tibial diaphysis) and trabecular (proximal tibia and L4 vertebrae) bone. DXA and mechanical testing was performed on the L5 vertebra. After 8 wk of treatment, trabecular bone turnover rates were significantly suppressed in all drug-treated animals. Trabecular bone formation rate (BFR/BS) remained significantly lower than vehicle in bisphosphonate-treated animals through 12 wk. Sixteen weeks after treatment withdrawal, trabecular BFR/BS in the proximal tibia was re-established in animals treated with RIS but not in animals treated with ALN compared with controls. BMD of the fifth lumbar vertebra remained significantly higher than controls 16 wk after treatment withdrawal in ALN-treated animals but not in RIS-treated animals. Despite reductions in BMD and increases in bone turnover, ultimate force of the fifth lumbar vertebra remained significantly higher in all drug-treated animals through 16 wk after withdrawal. [source] Targeted Deletion of the Sclerostin Gene in Mice Results in Increased Bone Formation and Bone Strength,,JOURNAL OF BONE AND MINERAL RESEARCH, Issue 6 2008Xiaodong Li Abstract Introduction: Sclerosteosis is a rare high bone mass genetic disorder in humans caused by inactivating mutations in SOST, the gene encoding sclerostin. Based on these data, sclerostin has emerged as a key negative regulator of bone mass. We generated SOST knockout (KO) mice to gain a more detailed understanding of the effects of sclerostin deficiency on bone. Materials and Methods: Gene targeting was used to inactivate SOST and generate a line of SOST KO mice. Radiography, densitometry, ,CT, histomorphometry, and mechanical testing were used to characterize the impact of sclerostin deficiency on bone in male and female mice. Comparisons were made between same sex KO and wildtype (WT) mice. Results: The results for male and female SOST KO mice were similar, with differences only in the magnitude of some effects. SOST KO mice had increased radiodensity throughout the skeleton, with general skeletal morphology being normal in appearance. DXA analysis of lumbar vertebrae and whole leg showed that there was a significant increase in BMD (>50%) at both sites. ,CT analysis of femur showed that bone volume was significantly increased in both the trabecular and cortical compartments. Histomorphometry of trabecular bone revealed a significant increase in osteoblast surface and no significant change in osteoclast surface in SOST KO mice. The bone formation rate in SOST KO mice was significantly increased for trabecular bone (>9-fold) at the distal femur, as well as for the endocortical and periosteal surfaces of the femur midshaft. Mechanical testing of lumbar vertebrae and femur showed that bone strength was significantly increased at both sites in SOST KO mice. Conclusions:SOST KO mice have a high bone mass phenotype characterized by marked increases in BMD, bone volume, bone formation, and bone strength. These results show that sclerostin is a key negative regulator of a powerful, evolutionarily conserved bone formation pathway that acts on both trabecular and cortical bone. [source] Influence of Orthogonal Overload on Human Vertebral Trabecular Bone Mechanical Properties,JOURNAL OF BONE AND MINERAL RESEARCH, Issue 11 2007Arash Badiei Abstract The aim of this study was to investigate the effects of overload in orthogonal directions on longitudinal and transverse mechanical integrity in human vertebral trabecular bone. Results suggest that the trabecular structure has properties that act to minimize the decrease of apparent toughness transverse to the primary loading direction. Introduction: The maintenance of mechanical integrity and function of trabecular structure after overload remains largely unexplored. Whereas a number of studies have focused on addressing the question by testing the principal anatomical loading direction, the mechanical anisotropy has been overlooked. The aim of this study was to investigate the effects of overload in orthogonal directions on longitudinal and transverse mechanical integrity in human vertebral trabecular bone. Materials and Methods: T12/L1 vertebral bodies from five cases and L4/L5 vertebral bodies from seven cases were retrieved at autopsy. A cube of trabecular bone was cut from the centrum of each vertebral body and imaged by ,CT. Cubes from each T12/L1 and L4/L5 pairs were assigned to either superoinferior (SI) or anteroposterior (AP) mechanical testing groups. All samples were mechanically tested to 10% apparent strain by uniaxial compression according to their SI or AP allocation. To elucidate the extent to which overload in orthogonal directions affects the mechanical integrity of the trabecular structure, samples were retested (after initial uniaxial compression) in their orthogonal direction. After mechanical testing in each direction, apparent ultimate failure stresses (UFS), apparent elastic moduli (E), and apparent toughness moduli (u) were computed. Results: Significant differences in mechanical properties were found between SI and AP directions in both first and second overload tests. Mechanical anisotropy far exceeded differences resulting from overloading the structure in the orthogonal direction. No significant differences were found in mean UFS and mean u for the first or second overload tests. A significant decrease of 35% was identified in mean E for cubes overloaded in the SI direction and then overloaded in the AP direction. Conclusions: Observed differences in the mechanics of trabecular structure after overload suggests that the trabecular structure has properties that act to minimize loss of apparent toughness, perhaps through energy dissipating sacrificial structures transverse to the primary loading direction. [source] Quantitative Ultrasound Does Not Reflect Mechanically Induced Damage in Human Cancellous BoneJOURNAL OF BONE AND MINERAL RESEARCH, Issue 12 2000P. H. F. Nicholson Abstract This study investigated the ability of quantitative ultrasound (QUS) to detect reductions in the elastic modulus of cancellous bone caused by mechanical damage. Ultrasonic velocity and attenuation were measured using an in-house parametric imaging system in 46 cancellous bone cores from the human calcaneus. Each core was subjected to a mechanical testing regime to (a) determine the predamage elastic modulus, (b) induce damage by applying specified strains in excess of the yield strain, and (c) measure the postdamage elastic modulus. The specimens were divided into four groups: a control group subjected to a nominally nondestructive 0.7% maximum strain (,m) and three damage groups subjected to increasing strain levels (,m = 1.5, 3.0, and 4.5%). QUS measurements before and after the mechanical testing showed no significant differences between the control group and damage groups, despite highly significant (p < 0.001) reductions in the elastic modulus of up to 72%. These results indicate that current QUS techniques do not intrinsically reflect the elastic properties of cancellous bone. This is consistent with ultrasonic properties being determined by other factors (apparent density and/or architecture), which normally are associated strongly with elastic properties, but only when bone is mechanically intact. Clinically, this implies that ultrasound cannot be expected to detect bone fragility in the absence of major changes in bone density and/or trabecular architecture. [source] Relaxation Time Spectrum of Hydrogels by CONTIN AnalysisJOURNAL OF FOOD SCIENCE, Issue 3 2000R. Mao ABSTRACT: CONTIN is a general-purpose program for inverting noisy linear algebraic and integral equations by means of inverse Laplace transform. This study explored the application of CONTIN analysis to determine the relaxation time distribution spectra for food gels, including gellan, carrageenan, whey protein, and gelatin gels, based on stress-relaxation data. CONTIN results represent the continuous relaxation time spectra when the number of the terms in the discrete Maxwell stress-relaxation model approached infinity. The CONTIN results for gellan gels were correlated to the texture properties of gels from compression tests with respect to the effects of calcium concentrations. CONTIN analysis may be a very effective tool in elucidating the microstructural properties of a hydrogel from mechanical testing. [source] Early healing of flexor tendon insertion site injuries: Tunnel repair is mechanically and histologically inferior to surface repair in a canine modelJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 5 2006Matthew J. Silva Abstract Orthopedic injuries often require surgical reattachment of tendon to bone. Tendon ends can be sutured to bone by direct apposition to the bone surface or by placement within a bone tunnel. Our objective was to compare early healing of a traditional surface versus a novel tunnel method for repair of the flexor digitorum profundus (FDP) tendon insertion site in a canine model. A total of 70 tendon,bone specimens were analyzed 0, 5, 10 or 21 days after injury and repair, using tensile and range of motion mechanical testing, histology and densitometry. Ultimate force (a measure of repair strength) did not differ between surface and tunnel repairs at day 0. Both repair types had reduced strength at 10 and 21 days compared to 0 days, indicative of deterioration of suture grasping strength (tendon softening). At 21 days, tendons repaired in a bone tunnel had 38% lower ultimate force compared to surface repairs (p,=,0.017). Histological findings were comparable between repair groups at 5 and 10 days but differed at 21 days, when we saw evidence of maturation of the tendon,bone interface in the surface repairs compared to an immature fibrous interface with no evidence of tendon,bone integration in the tunnel repairs. After accounting for bone removed by the tunnel, no difference in bone mineral density or trabecular bone volume existed between surface and tunnel repairs. If the results of our animal study extend to healing of the human FDP insertion, they indicate that FDP tendons should be reattached to the distal phalanx by suture to the cortical surface rather than suture in a bone tunnel. © 2006 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res [source] Repair of rabbit segmental defects with the thrombin peptide, TP508JOURNAL OF ORTHOPAEDIC RESEARCH, Issue 5 2004Michael R. Sheller Abstract The synthetic peptide, TP508 (Chrysalin®), was delivered to rabbit segmental bone defects in biodegradable controlled-release PLGA microspheres to determine its potential efficacy for enhancing healing of non-critically and critically sized segmental defects. Non-critically sized radial defects were created in the forelimbs of New Zealand White rabbits, which were randomized into three treatment groups receiving 10, 50 and 100 ,g doses of TP508 in the right radius and control microspheres (without TP508) in the left radius. Torsional testing of the radii at six weeks showed a significant increase in ultimate torque, failure torque, ultimate energy, failure energy, and stiffness when treated with TP508 compared to controls (p < 0.01 for all measures). Thus, TP508 appeared to enhance or accelerate bone growth in these defects. In a second set of experiments, critically sized ulnar defects were created in the forelimbs of New Zealand White rabbits, which were randomized into two groups with each rabbit receiving microspheres with 100 or 200 ,g of TP508 into the right ulnar defect and control microspheres (without TP508) alone into the left ulnar defect. Bone healing was evaluated with plain radiographs, synchrotron-based microtomography, and mechanical testing. Radiographs of the rabbit limbs scored by three blinded, independent reviewers demonstrated a significantly higher degree of healing when treated with TP508 than their untreated control limbs (p < 0.05). Three-dimensional synchrotron tomography of a limited number of samples showed that the new bone in TP508-treated samples had a less porous surface appearance and open marrow spaces, suggesting progression of bone remodeling. Torsional testing of the ulnae at nine weeks showed a significant increase in maximum torque and failure energy when treated with TP508 compared to controls (p < 0.01 for both measures). These results suggest that TP508 in a controlled release delivery vehicle has the potential to enhance healing of segmental defects in both critically and non-critically sized defects. © 2004 Orthopaedic Research Society. Published by Elsevier Ltd. All rights reserved. [source] Effects of h-PTH on cancellous bone mass, connectivity, and bone strength in ovariectomized rats with and without sciatic-neurectomyJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 3 2004Y. Kasukawa Abstract The purpose of this study was to determine whether h-PTH (1-34) treatment would recover cancellous bone connectivity and bone strength in ovariectomized (OVX) or ovariectomized and sciatic-neurectomized (OVX + NX) rats. Seven-month-old female Wistar rats were treated with h-PTH or vehicle (6.0 ,g/kg, six times a week, subcutaneously) for four weeks beginning 4, 8, or 12 weeks after OVX or OVX + NX. These were compared to age-matched baseline and sham-operated groups. Right tibiae were used for bone histomorphometry and node-strut analysis, and left tibiae were used for mechanical testing. The bone formation rates in the OVX and OVX + NX rats treated with h-PTH were significantly higher than those in their baseline controls, h-PTH treatment increased the node numbers and failure energies in the OVX rats, compared to their baseline controls, at all time points. However, in the OVX + NX rats, the effects of h-PTH treatment on the node number and failure energy were observed only at four weeks after surgery, but not at eight weeks or 12 weeks after surgery. These results suggest that the lowest limit, at which trabecular connectivity and bone strength are able to be restored by h-PTH, occurred between four and eight weeks in OVX + NX rats, but not in OVX rats, h-PTH cannot recover trabecular connectivity and bone strength in advanced osteopenia. © 2003 Orthopaedic Research Society. Published by Elsevier Ltd. All rights reserved. [source] Synthesis of polyethylene-octene elastomer/SiO2 -TiO2 nanocomposites via in situ polymerization: Properties and characterization of the hybridJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 8 2005Chin-San Wu Abstract In this study, a silicic acid and tetra isopropyl ortho titanate ceramic precursor and a metallocene polyethylene-octene elastomer (POE) or acrylic acid grafted metallocene polyethylene-octene elastomer (POE-g-AA) were used in the preparation of hybrids (POE/SiO2TiO2 and POE-g-AA/SiO2TiO2) using an in situ sol-gel process, with a view to identifying a hybrid with improved thermal and mechanical properties. Hybrids were characterized using Fourier transform infrared spectroscopy, 29Si solid-state nuclear magnetic resonance (NMR), X-ray diffraction, differential scanning calorimetry, thermogravimetry analysis, dynamic mechanical thermal analysis, and Instron mechanical testing. Properties of the POE-g-AA/SiO2TiO2 hybrid were superior to those of the POE/SiO2TiO2 hybrid. This was because the carboxylic acid groups of acrylic acid acted as coordination sites for the silica-titania phase to allow the formation of stronger chemical bonds. 29Si solid-state NMR showed that Si atoms coordinated around SiO4 units were predominantly Q3 and Q4. The 10 wt % SiO2TiO2 hybrids gave the maximum values of tensile strength and glass transition temperature in both POE/SiO2TiO2 and POE-g-AA/SiO2TiO2. It is proposed that above this wt %, excess SiO2TiO2 particles caused separation between the organic and inorganic phases. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1690,1701, 2005 [source] Biofunctional rapid prototyping for tissue-engineering applications: 3D bioplotting versus 3D printing,JOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 3 2004Andreas Pfister Abstract Two important rapid-prototyping technologies (3D Printing and 3D Bioplotting) were compared with respect to the computer-aided design and free-form fabrication of biodegradable polyurethane scaffolds meeting the demands of tissue-engineering applications. Aliphatic polyurethanes were based on lysine ethyl ester diisocyanate and isophorone diisocyanate. Layer-by-layer construction of the scaffolds was performed by 3D Printing, that is, bonding together starch particles followed by infiltration and partial crosslinking of starch with lysine ethyl ester diisocyanate. Alternatively, the 3D Bioplotting process permitted three-dimensional dispensing and reactive processing of oligoetherurethanes derived from isophorone diisocyanate, oligoethylene oxide, and glycerol. The scaffolds were characterized with X-ray microtomography, scanning electron microscopy, and mechanical testing. Osteoblast-like cells were seeded on such scaffolds to demonstrate their potential in tissue engineering. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 624,638, 2004 [source] RELATIONSHIPS BETWEEN PRIMARY PLANT CELL WALL ARCHITECTURE AND MECHANICAL PROPERTIES FOR ONION BULB SCALE EPIDERMAL CELLSJOURNAL OF TEXTURE STUDIES, Issue 6 2004DAVID G. HEPWORTH ABSTRACT This article investigates onion epidermal tissue (Allium cepa) using a combination of mechanical testing, microscopy and modeling and relates tissue mechanical properties to the known structure of the cell walls. Onion epidermal tissue has a simple, regular structure of elongated cells, which have been used to enable the contributions to mechanical properties of cell walls and of higher order structures to be separated and analyzed. Two models of wall behavior were used to explore how Poisson's ratio of cell walls parallel to the plane of the epidermal surface may vary with applied strain. In the first model, cellulose microfibrils can be reorientated in an unrestricted way with the result that the cell wall volume decreases. In the second model the volume of the cell wall remains constant, which controls the reorientation of microfibrils, hence the Poisson's ratio. Measurements made from uniaxially stretched cells show that the data most closely fits model I, therefore, it is concluded that the bulk of the matrix has little influence on the observed mechanical properties (at a test rate of 1 mm/min), allowing cellulose microfibrils to reorient through the matrix in an unrestricted way during uniaxial tests. In its mechanical attributes the primary cell wall resembles more a knitted cloth than a semisolid composite material. When biaxial stretching is applied to tissue, so that there is no re-orientation of microfibrils, the cell wall material is still able to reach surprisingly large elastic strains of up to 12.5% and no plastic deformation was recorded. Current theory suggests that cellulose microfibrils can stretch elastically by a maximum of 7%, therefore further work is required to identify mechanisms that could account for the extra elastic strain. [source] Physicochemical properties and application of pullulan edible films and coatings in fruit preservationJOURNAL OF THE SCIENCE OF FOOD AND AGRICULTURE, Issue 10 2001Tony Diab Abstract The effects of water, sorbitol and a sucrose fatty acid ester (SE) on the water sorption behaviour and thermal and mechanical properties of pullulan-based edible films as well as the physiological responses of fruit coated with pullulan have been studied. Incorporation of sorbitol or SE in pullulan films resulted in lower equilibrium moisture contents at low to intermediate water activities (aw), but much higher moisture contents at aw,>,0.75; estimates of monolayer values (within 4.1,5.9,gH2O,kg,1 solids) were given by application of the Brunauer,Emmett,Teller (BET) and Guggenheim,Anderson,DeBoer (GAB) models. A single glass,rubber transition (Tg), attributed to the polysaccharide component, was detected by calorimetry and dynamic mechanical thermal analysis (DMTA) at a sorbitol level of 15,30% DM. With both tests the strong plasticising action of water and polyol was evident in the thermal curves, and the Tg vs moisture content data were successfully fitted to the Gordon,Taylor empirical model. Multifrequency DMTA measurements provided estimates for the apparent activation energy of the glass transition in the range of , 300,488,kJ,mol,1. With large-deformation mechanical testing, large decreases in Young's moduli (tensile and three-point bend tests) were observed as a result of water- and/or polyol-mediated glass-to-rubber transition of the polymeric films. In the moisture content range of 2,8%, increases in flexural modulus (E) and maximum stress (,max) with small increases in moisture content were found for films made of pullulan or pullulan mixed with 15% DM sorbitol; a strong softening effect was observed when the water content exceeded this range. Addition of sorbitol increased the water vapour transmission rate of the films, whereas addition of SE had the opposite effect. Application of a pullulan/sorbitol/SE coating on strawberries resulted in large changes in internal fruit atmosphere composition which were beneficial for extending the shelf-life of this fruit; the coated fruit showed much higher levels of CO2, a large reduction in internal O2, better firmness and colour retention and a reduced rate of weight loss. In contrast, similar studies on whole kiwifruits showed increased levels of internal ethylene, which caused acceleration of fruit ripening during storage. © 2001 Society of Chemical Industry [source] Hydrogen degradation of structural steels in technical hydrocarbon liquidsMATERIALS AND CORROSION/WERKSTOFFE UND KORROSION, Issue 4 2008B. Swieczko-Zurek Abstract Hydrogen absorption, mechanical testing under different loading mode and electrochemical measurement were done for 0.3C low alloy steels used in the ship engine parts at immersion in the boiler fuel and in the used engine mineral oil at elevated temperatures corresponding to the operating conditions. The hydrogen charging of steels has been found to reach a level causing their plasticity loss. No effect, a plasticity loss and a significant decrease in the number of cycles have been stated in constant load, slow strain rate and fatigue tests, respectively. The results showed the local active plastic deformation proceeded close to the surface of hydrogen ingress to provide the highest possibility for hydrogen induced metal degradation in hydrocarbon environments. Although the source of hydrogen evolved in the case of technical hydrocarbons has been discussed, the promoting effect of formed H2S should be recognized as the important factor influencing the hydrogen charging from those environments. Some variation in the steel microstructure, chemical composition and hardness of steels, even allowed by the standard may affect their susceptibility to hydrogen degradation in hydrocarbons. [source] Transplantation of a vascularized rabbit femoral diaphyseal segment: Mechanical and histologic properties of a new living bone transplantation modelMICROSURGERY, Issue 4 2008Goetz A. Giessler M.D. A new vascularized bone transplantation model is described, including the anatomy and surgical technique of isolating a rabbit femoral diaphyseal segment on its nutrient vascular pedicle. The histologic and biomechanical parameters of pedicled vascularized femoral autotransplants were studied following orthotopic reimplantation in the resulting mid-diaphyseal defect. Vascularized femur segments were isolated in 10 rabbits on their nutrient pedicle, and then replaced orthotopically with appropriate internal fixation. Postoperative weightbearing and mobility were unrestricted, and the contralateral femora served as no-treatment controls. After 16 weeks, the bone flaps were evaluated by x-ray (bone healing), mechanical testing (material properties), microangiography (quantification of intraosseous vasculature), histology (bone viability), and histomorphometry (bone remodeling). Bone healing occurred by 2 weeks, with further callus remodeling throughout the survival period. Eight transplants healed completely, while two had a distal pseudarthrosis. Microangiography demonstrated patent pedicles in all transplants. Intraosseous vessel densities were comparable to nonoperated (control) femora. We found ultimate strength and elastic modulus to be significantly reduced when compared to normal controls. Viable bone, increased mineral apposition rate, and bone turnover were demonstrated in all transplants. The method described, and the data provided will be of value for the further study of isolated segments of living bone, and in particular, for investigations of reconstruction of segmental bone loss in weight-bearing animal models. This study also provides important normative data on living autologous bone flap material properties, vascularity, and bone remodeling. We intend to use this method and data for comparison in subsequent studies of large bone vascularized allotransplantation. © 2008 Wiley-Liss, Inc. Microsurgery, 2008. [source] Functionalized polypropylenes in the compatibilization and dispersion of clay nanocompositesPOLYMER COMPOSITES, Issue 4 2006C. Varela The preparation of polypropylene (PP) nanocomposites was studied using clay and three types of modified PP (m-PP) as compatibilizers: diethyl maleate grafted PP (PP- g -DEM), maleic anhydride grafted PP (PP- g -MA), and PP grafted with carbamyl maleamic acid (PP- g -UMA). The clay was made organophylic by an acid treatment with octadecylamine. PP functionalization and blending were carried out in an internal mixer. Blends of PP containing 20 and 40 wt% each of the modified PP and 5 wt% of organophilic clay (IMt), in each case, were prepared. Samples were characterized by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), optical microscopy, and mechanical testing. The presence of tactoid, intercalated and exfoliated structures was observed by TEM in all the samples containing clay and modified PP, which also showed improved mechanical properties with tensile modulus as much as three times that of PP. Melting temperature did not vary significantly with the addition of clay. However, because of the clay's nucleating effect, an increase in the crystallization temperature was observed, accompanied by a slight decrease in the degree of crystallinity. The best results were obtained when PP- g -MA was used as the compatibilizer; intermediate results were obtained with the use of PP- g -UMA, followed by the results obtained when PP- g -DEM was used. Property enhancements were obtained when a higher percentage of modified PP was employed. POLYM. COMPOS., 27:451,460, 2006. © 2006 Society of Plastics Engineers [source] Effect of orientation and crystallinity on the photodegradation of poly(ethylene terephthalate) fibersPOLYMER ENGINEERING & SCIENCE, Issue 5 2008H. Fashandi In this research, photodegradation of poly(ethylene terephthalate) (PET) fibers was investigated with emphasis on the morphological state of yarns. Two kinds of yarns, FDY (Fully Drawn Yarn) and POY (Partially Oriented Yarn), with different molecular orientation and crystallinity were applied in this research. FDY is spun in the same way as POY and subsequently drawn at high speed and then entangled before winding up. This sample has higher molecular orientation and crystallinity than the POY sample. Several analytical methods were applied in this study: viscometry, X-ray diffraction, FTIR spectroscopy, UV,Visible spectrophotometry, and mechanical testing. Viscometry was used to determine molecular weight as a monitoring factor for degradation. X-ray diagrams showed higher crystallinity for FDY samples during weathering process by irradiation. Results of mechanical testing indicated that the tenacity of the FDY fibers had less deterioration in comparison with the POY ones. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers [source] Recycling of poly(ethylene terephthalate) as polymer-polymer composites,POLYMER ENGINEERING & SCIENCE, Issue 4 2002M. Evstatiev Microfibrillar reinforced composites (MFC) comprising an isotropic matrix from a lower melting polymer reinforced by microfibrils of a higher melting polymer were manufactured under industrially relevant conditions and processed via injection molding. Low density polyethylene (LDPE) (matrix) and recycled poly(ethylene terephthalate) (PET) (reinforcing material) from bottles were melt blended (in 30/70 and 50/50 PET/LDPE wt ratio) and extruded, followed by continuous drawing, pelletizing and injection molding of dogbone samples. Samples of each stage of MFC manufacturing and processing were characterized by means of scanning electron microscopy (SEM), wide-angle X-ray scattering (WAXS), dynamic mechanical thermal analysis (DMTA), and mechanical testing. SEM and WAXS showed that the extruded blend is isotropic but becomes highly oriented after drawing, being converted into a polymer-polymer composite upon injection molding at temperatures below the melting temperature of PET. This MFC is characterized by an isotropic LDPE matrix reinforced by randomly distributed PET microfibrils, as concluded from the WAXS patterns and SEM observations. The MFC dogbone samples show impressive mechanical properties,the elastic modulus is about 10 times higher than that of LDPE and about three times higher than reinforced LDPE with glass spheres, approaching the modulus of LDPE reinforced with 30 wt% short-glass fibers (GF). The tensile strength is at least two times higher than that of LDPE or of reinforced LDPE with glass spheres, approaching that of reinforced LDPE with 30 wt% GF. The impact strength of LDPE increases by 50% after reinforcement with PET. It is concluded that: (i) the MFC approach can be applied in industrially relevant conditions using various blend partners, and (ii) the MFC concept represents an attractive alternative for recycling of PET as well as other polymers. [source] | ||||||||||||||||||||||||||||