Home About us Contact
|
Home About us Contact | ||
|
|
||
LUMO Energy Level (lumo + energy_level)
Selected AbstractsHigh-Yield Synthesis and Electrochemical and Photovoltaic Properties of Indene-C70 BisadductADVANCED FUNCTIONAL MATERIALS, Issue 19 2010Youjun He Abstract [6, 6]-Phenyl-C61 -butyric acid methyl ester (PC60BM) is the widely used acceptor material in polymer solar cells (PSCs). Nevertheless, the low LUMO energy level and weak absorption in visible region are its two weak points. For enhancing the solar light harvest, the soluble C70 derivative PC70BM has been used as acceptor instead of PC60BM in high efficiency PSCs in recent years. But, the LUMO level of PC70BM is the same as that of PC60BM, which is too low for the PSCs based on the polymer donors with higher HOMO level, such as poly (3-hexylthiophene) (P3HT). Here, a new soluble C70 derivative, indene-C70 bisadduct (IC70BA), is synthesized with high yield of 58% by a one-pot reaction of indene and C70 at 180 °C for 72 h. The electrochemical properties and electronic energy levels of the fullerene derivatives are measured by cyclic voltammetry. The LUMO energy level of IC70BA is 0.19 eV higher than that of PC70BM. The PSC based on P3HT with IC70BA as acceptor shows a higher Voc of 0.84 V and higher power conversion efficiency (PCE) of 5.64%, while the PSC based on P3HT/PC60BM and P3HT/PC70BM displays Voc of 0.59 V and 0.58 V, and PCE of 3.55% and 3.96%, respectively, under the illumination of AM1.5G, 100 mW cm,2. The results indicate that IC70BA is an excellent acceptor for the P3HT-based PSCs and could be a promising new acceptor instead of PC70BM for the high performance PSCs based on narrow bandgap conjugated polymer donor. [source] Thiophene,Benzothiadiazole Co-Oligomers: Synthesis, Optoelectronic Properties, Electrical Characterization, and Thin-Film PatterningADVANCED FUNCTIONAL MATERIALS, Issue 3 2010Manuela Melucci Abstract Newly synthesized thiophene (T) and benzothiadiazole (B) co-oligomers of different size, alternation motifs, and alkyl substitution types are reported. Combined spectroscopic data, electrochemical analysis, and theoretical calculations show that the insertion of a single electron-deficient B unit into the aromatic backbone strongly affects the LUMO energy level. The insertion of additional B units has only a minor effect on the electronic properties. Cast films of oligomers with two alternated B rings (B,T,B inner core) display crystalline order. Bottom-contact FETs based on films cast on bare SiO2 show hole-charge mobilities of 1,×,10,3,5,×,10,3,cm2 V,1s,1 and Ion/Ioff ratios of 105,106. Solution-cast films of cyclohexyl-substituted compounds are amorphous and do not show FET behavior. However, the lack of order observed in these films can be overcome by nanorubbing and unconventional wet lithography, which allow for fine control of structural order in thin deposits. [source] Synthesis and applications of low-bandgap conjugated polymers containing phenothiazine donor and various benzodiazole acceptors for polymer solar cellsJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 21 2010Harihara Padhy Abstract A series of soluble donor-acceptor conjugated polymers comprising of phenothiazine donor and various benzodiazole acceptors (i.e., benzothiadiazole, benzoselenodiazole, and benzoxadiazole) sandwiched between hexyl-thiophene linkers were designed, synthesized, and used for the fabrication of polymer solar cells (PSC). The effects of the benzodiazole acceptors on the thermal, optical, electrochemical, and photovoltaic properties of these low-bandgap (LBG) polymers were investigated. These LBG polymers possessed large molecular weight (Mn) in the range of 3.85,5.13 × 104 with high thermal decomposition temperatures, which demonstrated broad absorption in the region of 300,750 nm with optical bandgaps of 1.80,1.93 eV. Both the HOMO energy level (,5.38 to ,5.47 eV) and LUMO energy level (,3.47 to ,3.60 eV) of the LBG polymers were within the desirable range of ideal energy level. Under 100 mW/cm2 of AM 1.5 white-light illumination, bulk heterojunction PSC devices containing an active layer of electron donor polymers mixed with electron acceptor [6,6]-phenyl-C61 -butyric acid methyl ester (PC61BM) or [6,6]-phenyl-C71 -butyric acid methyl ester (PC71BM) in different weight ratios were investigated. The best performance of the PSC device was obtained by using polymer PP6DHTBT as an electron donor and PC71BM as an acceptor in the weight ratio of 1:4, and a power conversion efficiency value of 1.20%, an open-circuit voltage (Voc) value of 0.75 V, a short-circuit current (Jsc) value of 4.60 mA/cm2, and a fill factor (FF) value of 35.0% were achieved. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010 [source] Effect of Carbon Chain Length in the Substituent of PCBM-like Molecules on Their Photovoltaic PropertiesADVANCED FUNCTIONAL MATERIALS, Issue 9 2010Guangjin Zhao Abstract A series of [6,6]-phenyl-C61 -butyric acid methyl ester (PCBM)-like fullerene derivatives with the butyl chain in PCBM changing from 3 to 7 carbon atoms, respectively (F1,F5), are designed and synthesized to investigate the relationship between photovoltaic properties and the molecular structure of fullerene derivative acceptors. F2 with a butyl chain is PCBM itself for comparison. Electrochemical, optical, electron mobility, morphology, and photovoltaic properties of the molecules are characterized, and the effect of the alkyl chain length on their properties is investigated. Although there is little difference in the absorption spectra and LUMO energy levels of F1,F5, an interesting effect of the alkyl chain length on the photovoltaic properties is observed. For the polymer solar cells (PSCs) based on P3HT as donor and F1,F5, respectively, as acceptors, the photovoltaic behavior of the P3HT/F1 and P3HT/F4 systems are similar to or a little better than that of the P3HT/PCBM device with power conversion efficiencies (PCEs) above 3.5%, while the performances of P3HT/F3 and P3HT/F5-based solar cells are poorer, with PCE values below 3.0%. The phenomenon is explained by the effect of the alkyl chain length on the absorption spectra, fluorescence quenching degree, electron mobility, and morphology of the P3HT/F1,F5 (1:1, w/w) blend films. [source] Tuning the Optoelectronic Properties of Carbazole/Oxadiazole Hybrids through Linkage Modes: Hosts for Highly Efficient Green ElectrophosphorescenceADVANCED FUNCTIONAL MATERIALS, Issue 2 2010Youtian Tao Abstract A series of bipolar transport host materials: 2,5-bis(2-(9H -carbazol-9-yl)phenyl)-1,3,4-oxadiazole (o -CzOXD) (1), 2,5-bis(4-(9H -carbazol-9-yl)phenyl)-1,3,4-oxadiazole (p -CzOXD) (2), 2,5-bis(3-(9H -carbazol-9-yl)phenyl)-1,3,4-oxadiazole (m -CzOXD) (3) and 2-(2-(9H -carbazol-9-yl)phenyl)-5-(4-(9H-carbazol-9-yl)phenyl)-1,3,4-oxadiazole (op -CzOXD) (4) are synthesized through simple aromatic nucleophilic substitution reactions. The incorporation of the oxadiazole moiety greatly improves their morphological stability, with Td and Tg in the range of 428,464,°C and 97,133,°C, respectively. The ortho and meta positions of the 2,5-diphenyl-1,3,4-oxadiazole linked hybrids (1 and 3) show less intramolecular charge transfer and a higher triplet energy compared to the para-position linked analogue (2). The four compounds exhibit similar LUMO levels (2.55,2.59,eV) to other oxadiazole derivatives, whereas the HOMO levels vary in a range from 5.55,eV to 5.69,eV, depending on the linkage modes. DFT-calculation results indicate that 1, 3, and 4 have almost complete separation of their HOMO and LUMO levels at the hole- and electron-transporting moieties, while 2 exhibits only partial separation of the HOMO and LUMO levels possibly due to intramolecular charge transfer. Phosphorescent organic light-emitting devices fabricated using 1,4 as hosts and a green emitter, Ir(ppy)3 or (ppy)2Ir(acac), as the guest exhibit good to excellent performance. Devices hosted by o -CzOXD (1) achieve maximum current efficiencies (,c) as high as 77.9,cd A,1 for Ir(ppy)3 and 64.2,cd A,1 for (ppy)2Ir(acac). The excellent device performance may be attributed to the well-matched energy levels between the host and hole-transport layers, the high triplet energy of the host and the complete spatial separation of HOMO and LUMO energy levels. [source] | ||||||||||