Home  About us  Contact
 

Investment Materials (investment + material)

Distribution by Scientific Domains
Medical Sciences100%

Kinds of Investment Materials

  • phosphate-bonded investment material
    		•

    Selected Abstracts

    Measurement of the setting expansion of phosphate-bonded investment materials: Part I , Development of the Casting-Ring Test

    JOURNAL OF ORAL REHABILITATION, Issue 7 2004
    C. H. Lloyd
    summary, The setting expansion is an important property for a phosphate-bonded investment material. This research was undertaken to investigate a test that might be suitable for its measurement when used in a Standard. In the ,Casting-Ring Test', the investment sample is contained in a steel ring and expands to displace a precisely positioned pin. Variables with the potential to alter routine reproduction of the value were investigated. The vacuum-mixer model is a production laboratory variable that must not be ignored and for this reason, experiments were repeated using a different vacuum-mixer located at a second test site. Restraint by the rigid ring material increased expansion, while force on the pin reduced it. Expansion was specific to the lining selected. Increased environmental temperature decreased the final value. Expansion was still taking place at a time at which its value might be measured. However, when these factors are set, the reproducibility of values for setting expansion was good at both test sites (coefficient of variation 14%, at most). The results revealed that with the control that is available reliable routine measurement is possible in a Standard test. The inter-laboratory variable, vacuum-mixer model, produced significant differences and it should be the subject of further investigation. [source]

    Differing Expansion Contributions of Three Investment Materials Used for Casting Titanium

    JOURNAL OF PROSTHODONTICS, Issue 5 2009
    Danny Low BDS, MScDent, MScMed
    Abstract Purpose: This laboratory study aimed at investigating the effect of setting expansion (SE), which could enlarge a wax pattern by concurrent exothermic reaction. Materials and Methods: Two phosphate-bonded investment materials (Rematitan Plus, T-invest C & B) and alumina-magnesia-based investment material (Titavest CB) were subjected to setting temperature and SE measurements (n = 10). Full-crown wax patterns were prepared from metal dies having the same design. Crown castings (n = 6) were made using a one-chamber high-pressure casting machine. Commercially pure titanium ingot (Japanese Industrial Standard Class II) was used for each casting. Dimensional accuracy of the cast crowns was expressed by marginal discrepancy for a pair of wax pattern and casting prepared from the same die. All results were then subjected to regression analysis. Results: Rematitan Plus gave the highest setting temperature (about 70°C) and the highest SE (1.16 ± 0.01%) almost concurrently. The result was that Rematitan Plus produced oversized crowns from the lowest thermal expansion (TE) value (0.53 ± 0.05%) reducing the linear correlation to 0.80 (p < 0.05). No significant linear relationship was found between SE of investment material and crown-casting accuracy. Conclusions: The almost concurrent occurrence of high SE and high setting temperature generation in Rematitan Plus enlarged the wax pattern and effectively supplemented its low TE to produce oversized crowns. Despite this adverse effect, the correlation between TE and crown accuracy was still high. It is generally expected that the TE values given by manufacturers predict crown accuracy, when uniform TE, small SE, and minimum heat generation during setting are assured. [source]

    Measurement of the setting expansion of phosphate-bonded investment materials: Part I , Development of the Casting-Ring Test

    JOURNAL OF ORAL REHABILITATION, Issue 7 2004
    C. H. Lloyd
    summary, The setting expansion is an important property for a phosphate-bonded investment material. This research was undertaken to investigate a test that might be suitable for its measurement when used in a Standard. In the ,Casting-Ring Test', the investment sample is contained in a steel ring and expands to displace a precisely positioned pin. Variables with the potential to alter routine reproduction of the value were investigated. The vacuum-mixer model is a production laboratory variable that must not be ignored and for this reason, experiments were repeated using a different vacuum-mixer located at a second test site. Restraint by the rigid ring material increased expansion, while force on the pin reduced it. Expansion was specific to the lining selected. Increased environmental temperature decreased the final value. Expansion was still taking place at a time at which its value might be measured. However, when these factors are set, the reproducibility of values for setting expansion was good at both test sites (coefficient of variation 14%, at most). The results revealed that with the control that is available reliable routine measurement is possible in a Standard test. The inter-laboratory variable, vacuum-mixer model, produced significant differences and it should be the subject of further investigation. [source]

    Measurement of the setting expansion of phosphate-bonded investment materials: Part II , An evaluation of the Casting-Ring Test at 10 laboratories

    JOURNAL OF ORAL REHABILITATION, Issue 7 2004
    C. H. Lloyd
    summary, The Casting-Ring Test has the potential to fulfil the requirement for a reliable ,Standard' test to measure the setting expansion of phosphate-bonded investment materials. The purpose of this study was to investigate the reproducibility of the measurements and the value that is produced at 10 test sites. The Casting-Ring Test apparatus, three phosphate-bonded investment products and one ring liner product were sent to the 10 participants, together with a detailed test protocol. Participants were asked to use their normal vacuum mixers. Reproducibility at individual sites was good. However, there were significant differences between test sites for the mean setting expansions, attributed to the range of vacuum mixers employed. From these results, the Casting-Ring Test appears to satisfy the requirements for adoption as an ISO standard test. The effect produced by different vacuum-mixer models would be manifest in any test. Not only does this have implications when determining the value of setting expansion for product information, but such a range of setting expansions will also be reproduced during production of moulds in commercial dental laboratory practice. However, for any specific product and vacuum-mixer combination, the setting expansion will be consistent and will not vary from mould to mould. [source]

    Differing Expansion Contributions of Three Investment Materials Used for Casting Titanium

    JOURNAL OF PROSTHODONTICS, Issue 5 2009
    Danny Low BDS, MScDent, MScMed
    Abstract Purpose: This laboratory study aimed at investigating the effect of setting expansion (SE), which could enlarge a wax pattern by concurrent exothermic reaction. Materials and Methods: Two phosphate-bonded investment materials (Rematitan Plus, T-invest C & B) and alumina-magnesia-based investment material (Titavest CB) were subjected to setting temperature and SE measurements (n = 10). Full-crown wax patterns were prepared from metal dies having the same design. Crown castings (n = 6) were made using a one-chamber high-pressure casting machine. Commercially pure titanium ingot (Japanese Industrial Standard Class II) was used for each casting. Dimensional accuracy of the cast crowns was expressed by marginal discrepancy for a pair of wax pattern and casting prepared from the same die. All results were then subjected to regression analysis. Results: Rematitan Plus gave the highest setting temperature (about 70°C) and the highest SE (1.16 ± 0.01%) almost concurrently. The result was that Rematitan Plus produced oversized crowns from the lowest thermal expansion (TE) value (0.53 ± 0.05%) reducing the linear correlation to 0.80 (p < 0.05). No significant linear relationship was found between SE of investment material and crown-casting accuracy. Conclusions: The almost concurrent occurrence of high SE and high setting temperature generation in Rematitan Plus enlarged the wax pattern and effectively supplemented its low TE to produce oversized crowns. Despite this adverse effect, the correlation between TE and crown accuracy was still high. It is generally expected that the TE values given by manufacturers predict crown accuracy, when uniform TE, small SE, and minimum heat generation during setting are assured. [source]