Home About us Contact
|
Home About us Contact | ||
|
|
||
Immobilization Method (immobilization + method)
Selected AbstractsApplication of Exchangeable Biochemical Reactors with Oxidase-Catalase-Co-immobilizates and Immobilized Microorganisms in a Microfluidic Chip-CalorimeterENGINEERING IN LIFE SCIENCES (ELECTRONIC), Issue 5 2008M. Leifheit Abstract Several methods for the quantitative detection of different compounds, e.g., L -amino acids, sugars or alcohols in liquid media were developed by application of an automatic measuring unit including a fluid chip-calorimeter FCC-21. For this purpose, enzymes were immobilized covalently on the inner and outer surface of CPG (controlled porous glass)-spherules with an outer diameter of 100,,m and filled into a micro flow-through reaction chamber (VR = 20,,L). The design of the measuring cell allows for easy insertion into the calorimeter device of a stored series of comfortably pre-fabricated measuring cells. These cells can be filled with different enzyme immobilizates. Different oxidases were used and co-immobilized with catalase for the improvement of the detection sensitivity. A signal amplification could be achieved up to a factor of 3.5 with this configuration. ,- D -glucose, ethanol and L -lysine could be detected in a range of 0.25,1.75,mM using glucose oxidase, alcohol oxidase and lysine oxidase. The group of oxidases in combination with the enzymatic catalysis of the intermediate H2O2 allows the quantitative detection of a large number of analytes. A good measurement and storage stability could be achieved for several weeks by this immobilization method. In addition to enzyme-based detection reactions, it was shown that living microorganisms can be immobilized in the reaction chamber. Thus, the system can be used as a whole-cell biosensor. The quantitative detection of phenol in the range of 10,100,,M could be performed using the actinomycete Rhodococcus sp. immobilized on glass beads by means of embedding into polymers. [source] Functionalized Multi-Wall Carbon Nanotubes for Lipase Immobilization,ADVANCED ENGINEERING MATERIALS, Issue 5 2010I. V. Pavlidis Abstract We examine the immobilization of lipase B from Candida antarctica on functionalized multi-wall carbon nanotubes (MWCNTs) through physical adsorption. MWCNTs functionalized with carboxyl-, amine- and ester- terminal groups on their surface are used as immobilization carriers. Dispersion of the nanotubes and the immobilization procedure take place in aqueous and low-water media. High enzyme loadings are attained, up to 25% of the weight of the carbon nanotubes. These novel biomaterials are characterized though FT-IR and Raman spectroscopy. The MWCNT,lipase bioconjugates exhibit high catalytic activity and increased storage and operational stability. The biomaterials retain more than 55% of their initial activity after 6 months at 4,°C, while they retain approximately 25% of their initial activity after 30 d of incubation in hexane at 60,°C. The catalytic behaviour of the immobilized enzyme depends on the terminal group of the carbon nanotubes, the concentration of the enzyme and the immobilization method employed. [source] Directed evolution of formate dehydrogenase from Candida boidinii for improved stability during entrapment in polyacrylamideFEBS JOURNAL, Issue 17 2006Marion B. Ansorge-Schumacher In two cycles of an error-prone PCR process, variants of formate dehydrogenase from Candida boidinii were created which revealed an up to 4.4-fold (440%) higher residual activity after entrapment in polyacrylamide gels than the wild-type enzyme. These were identified in an assay using single precursor molecules of polyacrylamide instead of the complete gel for selection. The stabilization resulted from an exchange of distinct lysine, glutamic acid, and cysteine residues remote from the active site, which did not affect the kinetics of the catalyzed reaction. Thermal stability increased at the exchange of lysine and glutamic acid, but decreased due the exchange of cysteine. Overall, the variants reveal very suitable properties for application in a technical synthetic process, enabling use of entrapment in polyacrylamide as an economic and versatile immobilization method. [source] Starting solutions for the boundary immobilization methodINTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN BIOMEDICAL ENGINEERING, Issue 6 2005J. Caldwell Abstract The boundary immobilization method (BIM) is extended to the cases of outward spherical and cylindrical solidifications, which involves the development of starting solutions. When applying the method to time-dependent problems, good agreement is achieved when comparing the positions of the moving boundary and the temperature distribution with those obtained by the perturbation method. Copyright © 2004 John Wiley & Sons, Ltd. [source] Covalent immobilization of ,-galactosidase on carrageenan coated with chitosanJOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2009Magdy M.M. Elnashar Abstract ,-Galactosidase was covalently immobilized to carrageenan coated with chitosan for the hydrolysis of lactose. The chitosan-carrageenan polyelectrolyte interaction was found to be dependent on the chitosan pH. At pH 4, the chitosan reached its maximum binding of 28.5% (w/w) where the chitosan surface density was 4.8 mg chitosan/cm2 g of carrageenan gel disks, using Muzzarelli method. Glutaraldehyde was used as a mediator to incorporate new functionality, aldehydic carbonyl group, to the bio-polymers for covalent attachment of ,-galactosidase. The enzyme was covalently immobilized to the biopolymer at a concentration of 2.73 mg protein per g of wet gel. FTIR proved the incorporation of the aldehydic carbonyl group to the carrageenan coated with chitosan at 1720 cm,1. The optimum time for enzyme immobilization was found to be 16 h, after which a plateau was reached. The enzyme loading increased from 2.65 U/g (control gel) to 10.92 U/g gel using the covalent technique. The gel's modification has shown to improve the carrageenan gel thermal stability as well as the immobilized enzyme. For example, the carrageenan gel treated with chitosan showed an outstanding thermal stability at 95°C compared with 35°C for the untreated carrageenan gel. Similarly, the immobilization process shifted the enzyme's optimum temperature from 50°C for the free enzyme towards a wider temperature range 45,55 °C indicating that the enzyme structure is strengthened by immobilization. In brief, the newly developed immobilization method is simple; the carrier is cheap, yet effective and can be used for the immobilization of other enzymes. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009 [source] Surface plasmon resonance label-free monitoring of antibody antigen interactions in real timeBIOCHEMISTRY AND MOLECULAR BIOLOGY EDUCATION, Issue 1 2007Asta Kausaite Abstract Detection of biologically active compounds is one of the most important topics in molecular biology and biochemistry. One of the most promising detection methods is based on the application of surface plasmon resonance for label-free detection of biologically active compounds. This method allows one to monitor binding events in real time without labeling. The system can therefore be used to determine both affinity and rate constants for interactions between various types of molecules. Here, we describe the application of a surface plasmon resonance biosensor for label-free investigation of the interaction between an immobilized antigen bovine serum albumin (BSA) and antibody rabbit anti-cow albumin IgG1 (anti-BSA). The formation of a self-assembled monolayer (SAM) over a gold surface is introduced into this laboratory training protocol as an effective immobilization method, which is very promising in biosensing systems based on detection of affinity interactions. In the next step, covalent attachment via artificially formed amide bonds is applied for the immobilization of proteins on the formed SAM surface. These experiments provide suitable experience for postgraduate students to help them understand immobilization of biologically active materials via SAMs, fundamentals of surface plasmon resonance biosensor applications, and determination of non-covalent biomolecular interactions. The experiment is designed for master and/or Ph.D. students. In some particular cases, this protocol might be adoptable for bachelor students that already have completed an extended biochemistry program that included a background in immunology. [source] An Efficient Hybrid, Nanostructured, Epoxidation Catalyst: Titanium Silsesquioxane,Polystyrene Copolymer Supported on SBA-15CHEMISTRY - A EUROPEAN JOURNAL, Issue 4 2007Lei Zhang Abstract A novel interfacial hybrid epoxidation catalyst was designed with a new immobilization method for homogeneous catalysts by coating an inorganic support with an organic polymer film containing active sites. The titanium silsesquioxane (TiPOSS) complex, which contains a single-site titanium active center, was immobilized successfully by in-situ copolymerization on a mesoporous SBA-15-supported polystyrene polymer. The resulting hybrid materials exhibit attractive textural properties (highly ordered mesostructure, large specific surface area (>380,m2,g,1) and pore volume (,0.46,cm3,g,1)), and high activity in the epoxidation of alkenes. In the epoxidation of cyclooctene with tert -butyl hydrogen peroxide (TBHP), the hybrid catalysts have rate constants comparable with that of their homogeneous counterpart, and can be recycled at least seven times. They can also catalyze the epoxidation of cyclooctene with aqueous H2O2 as the oxidant. In two-phase reaction media, the catalysts show much higher activity than their homogeneous counterpart due to the hydrophobic environment around the active centers. They behave as interfacial catalysts due to their multifunctionality, that is, the hydrophobicity of polystyrene and the polyhedral oligomeric silsesquioxanes (POSS), and the hydrophilicity of the silica and the mesoporous structure. Combination of the immobilization of homogeneous catalysts on two conventional supports, inorganic solid and organic polymer, is demonstrated to achieve novel heterogeneous catalytic ensembles with the merits of attractive textural properties, tunable surface properties, and optimized environments around the active sites. [source] | |||||||||||||