Home About us Contact
|
Home About us Contact | ||
|
|
||
Hydrolysis Process (hydrolysis + process)
Selected AbstractsEffects of Pressing Lignocellulosic Biomass on Sugar Yield in Two-Stage Dilute-Acid Hydrolysis ProcessBIOTECHNOLOGY PROGRESS, Issue 3 2002Kyoung Heon Kim Dilute sulfuric acid catalyzed hydrolysis of biomass such as wood chips often involves pressing the wood particles in a dewatering step (e.g., after acid impregnation) or in compression screw feeders commonly used in continuous hydrolysis reactors. This study addresses the effects of pressing biomass feedstocks using a hydraulic press on soluble sugar yield obtained from two-stage dilute-acid hydrolysis of softwood. The pressed acid-impregnated feedstock gave significantly lower soluble sugar yields than the never-pressed (i.e., partially air-dried or filtered) feedstock. Pressing acid-impregnated feedstocks before pretreatment resulted in a soluble hemicellulosic sugar yield of 76.9% from first-stage hydrolysis and a soluble glucose yield of 33.7% from second-stage hydrolysis. The dilute-acid hydrolysis of partially air-dried feedstocks having total solids and acid concentrations similar to those of pressed feedstocks gave yields of 87.0% hemicellulosic sugar and 46.9% glucose in the first and second stages, respectively. Microscopic examination of wood structures showed that pressing acid-impregnated wood chips from 34 to 54% total solids (TS) did not cause the wood structure to collapse. However, pressing first-stage pretreated wood chips (i.e., feedstock for second-stage hydrolysis) from approximately 30 to 43% TS caused the porous wood matrix to almost completely collapse. It is hypothesized that pressing alters the wood structure and distribution of acid within the cell cavities, leading to uneven heat and mass transfer during pretreatment using direct steam injection. Consequently, lower hydrolysis yield of soluble sugars results. Dewatering of corn stover by pressing did not impact negatively on the sugar yield from single-stage dilute-acid pretreatment. [source] A DFT study on the hydrolysis mechanism of NH-tautomeric antitumors of [HL][trans -RuCl4L(dmso- S)]INTERNATIONAL JOURNAL OF QUANTUM CHEMISTRY, Issue 6 2010Jin Can Chen Abstract The hydrolysis process of Ru (III) complex [Htrz][trans -RuCl4(1- H -1,2,4-triazole)(dmso- S)] 1, a potential antitumor complex similar to the well-known anticancer agent [ImH][trans -RuCl4(Im)(dmso- S)] (NAMI-A), has been investigated by using density functional theory (DFT) method, and the solvent effect was also considered and calculated by conductor-like polarizable calculation model (CPCM). Meanwhile, the hydrolysis process of the NH-tautomeric isomer, [Htrz][trans -RuCl4(4- H -1,2,4-triazole)(dmso- S)] 2, was also modeled and predicted by the same methods. The structural characteristics and the detailed energy profiles for the hydrolysis processes of two isomers have been obtained. The analysis of thermodynamic and kinetic characteristics of hydrolysis reaction suggests the following: for the first hydrolysis step, the Complex 1 has lower hydrolysis rate than the reported anticancer drug NAMI-A, and the result is in accordance with experimental one. However, Complex 1 has obviously higher hydrolysis rate than its isomer Complex 2, and the result was reasonably explained in theory. For the second hydrolysis step, the formation of cis -diaqua species is thermodynamic preferred to that of trans isomers. In addition, the trend in nucleophilic attack abilities (A) of hydrolysis products by pertinent biomolecules was revealed and predicted. © 2009 Wiley Periodicals, Inc. Int J Quantum Chem, 2010 [source] In vitro monitoring of surface mechanical properties of poly(L -lactic acid) using microhardnessJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2007C. Saiz-Arroyo Abstract Poly(L -lactic acid) (PLLA) was immersed in a simulated body fluid (SBF) solution at 37.5°C for distinct times. The variation of the surface mechanical properties of PLLA samples with immersion time was followed by microhardness. These measurements showed that PLLA microhardness decreased significantly (, 60%) after only 30 days of immersion. The results were explained in terms of hydrolytic degradation of the samples. The dependence of microhardness with the applied dwell time was also analyzed. The creep curves were successfully described by a power law. A decrease of the creep constant k as the immersion time increased was found. Differential scanning calorimetry was also used to analyze the changes in the physical properties of PLLA, namely in crystallinity degree (Xc) and glass transition temperature (Tg), as a function of the immersion time in SBF. A significant variation in the crystallinity degree of PLLA, initially nearly amorphous (Xc = 9%), was detected after only 3 days of immersion (Xc = 37%). The interpretation of this behavior was based on the hydrolysis process suffered by PLLA. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007 [source] Alkaline hydrolysis of cinnamaldehyde to benzaldehyde in the presence of ,-cyclodextrinAICHE JOURNAL, Issue 2 2010Hongyan Chen Abstract A facile, novel, and cost-effective alkaline hydrolysis process of cinnamaldehyde to benzaldehyde under rather mild conditions has been investigated systematically in the presence of ,-cyclodextrin (,-CD), with water as the only solvent. ,-CD could form inclusion complex with cinnamaldehyde in water, with molar ratio of 1:1, so as to promote the reaction selectivity. The complex has been investigated experimentally and with computational methods. 1H-NMR, ROESY, UV,Vis, and FTIR have been utilized to analyze the inclusion complex. It shows that the equilibrium constant for inclusion (Ka) is 363 M,1, and the standard Gibbs function for the reaction, ,,G (298 K), is ,14.6 kJ mol,1. In addition, the structures of the proposed inclusion compounds were optimized with hybrid ONIOM theory. Benzaldehyde could be obtained at an yield of 42% under optimum conditions [50°C, 18 h, 2% NaOH (w/v), cinnamaldehyde:,-CD (molar ratio) = 1:1]. To explain the experimental data, NMR, FTIR, and elemental analysis results were used to determine the main reaction by-product 1-naphthalenemethanol. A feasible reaction mechanism including the retro-Aldol condensation of cinnamaldehyde and the Aldol condensation of acetaldehyde and cinnamaldehyde in basic aqueous ,-CD solution has been proposed. The calculated activation energy for the reaction was 45.27 kJ mol,1 by initial concentrations method. © 2009 American Institute of Chemical Engineers AIChE J, 2010 [source] Stability and hydrolysis kinetics of spirosuccinimide type inhibitors of aldose reductase in aqueous solution and retardation of their hydrolysis by the target enzymeJOURNAL OF PHARMACEUTICAL SCIENCES, Issue 4 2008Masuo Kurono Abstract The stability and the hydrolysis kinetics of spirosuccinimide type aldose reductase (AR) inhibitors, SX-3030 (racemate) and its optical enantiomers (R - and S -isomers), were investigated in aqueous solution. The hydrolysis followed pseudo-first-order kinetics and showed significant pH dependence. Maximum solution stability was observed below pH 2.4, whereas the hydrolysis was gradually catalyzed by hydroxide ion at neutral to alkaline pH while the compounds exhibiting moderate pH-independent stability at acidic to neutral conditions (pH 4,7) to enable oral administration. A pK of 3.7 was obtained from the pH-rate profile, but this kinetically derived pK is approximately 2 pH units below the pK of the parent compounds, suggesting the presence of an acidic intermediate involved in the hydrolysis process. These findings, together with structural analysis, support the notion that the hydrolysis would proceed via nucleophilic attack of a water molecule or hydroxide ion on the scissile carbonyl bond of the succinimide ring to form a succinamic acid intermediate that has a ,-keto acid structure, followed by decarboxylation to give a racemized succinimide ring-opened product. On the other hand, the interconversion of the R - and S -isomers did not occur during hydrolysis; however, the hydrolysis of the R -isomer was markedly suppressed by the target enzyme AR whereas that of the S -isomer was not, indicating a high degree of complementarity of interacting surfaces between the R -isomer and the enzyme. The results in the present study could provide useful clues for facilitating the appropriate stabilization strategies as well as for evaluating the pharmacological effects on target tissues in vivo, and suggested that the R -isomer may be a suitable candidate as AR inhibitor. © 2007 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 97:1468,1483, 2008 [source] Chemical One Step Method to Prepare Polyaniline Nanofibers with Electromagnetic FunctionMACROMOLECULAR RAPID COMMUNICATIONS, Issue 5 2007Zhiming Zhang Abstract A "Chemical one step method" (COSM) is proposed to prepare electromagnetic functional composite nanofibers of polyaniline (PANI/, -Fe2O3) having a diameter of ,20 nm. In this approach FeCl3 is acts as the oxidant either for polymerization of aniline or for preparation of , -Fe2O3 magnets. Besides, it also provides protons produced by the hydrolysis process for doping PANI. It is found that the composite nanofibers have a high conductivity (10,1,,,100 S,·,cm,1) and super-paramagnetic properties (Ms,=,0.46,,,6.03 emu,·,g,1 and Hc,=,0) at room temperature, where the conductivity is mainly affected by the molar ratio of FeCl3 to aniline monomer whereas the magnetic properties are dominated by the amount of FeCl2. [source] Valorization of an industrial organosolv,sugarcane bagasse lignin: Characterization and use as a matrix in biobased composites reinforced with sisal fibersBIOTECHNOLOGY & BIOENGINEERING, Issue 4 2010Elaine C. Ramires Abstract In the present study, the main focus was the characterization and application of the by-product lignin isolated through an industrial organosolv acid hydrolysis process from sugarcane bagasse, aiming at the production of bioethanol. The sugarcane lignin was characterized and used to prepare phenolic-type resins. The analysis confirmed that the industrial sugarcane lignin is of HGS type, with a high proportion of the less substituted aromatic ring p -hydroxyphenyl units, which favors further reaction with formaldehyde. The lignin,formaldehyde resins were used to produce biobased composites reinforced with different proportions of randomly distributed sisal fibers. The presence of lignin moieties in both the fiber and matrix increases their mutual affinity, as confirmed by SEM images, which showed good adhesion at the biocomposite fiber/matrix interface. This in turn allowed good load transference from the matrix to the fiber, leading to biobased composites with good impact strength (near 500,J,m,1 for a 40,wt% sisal fiber-reinforced composite). The study demonstrates that sugarcane bagasse lignin obtained from a bioethanol plant can be used without excessive purification in the preparation of lignocellulosic fiber-reinforced biobased composites displaying high mechanical properties. Biotechnol. Bioeng. 2010;107:612,621. © 2010 Wiley Periodicals, Inc. [source] A DFT study on the hydrolysis mechanism of NH-tautomeric antitumors of [HL][trans -RuCl4L(dmso- S)]INTERNATIONAL JOURNAL OF QUANTUM CHEMISTRY, Issue 6 2010Jin Can Chen Abstract The hydrolysis process of Ru (III) complex [Htrz][trans -RuCl4(1- H -1,2,4-triazole)(dmso- S)] 1, a potential antitumor complex similar to the well-known anticancer agent [ImH][trans -RuCl4(Im)(dmso- S)] (NAMI-A), has been investigated by using density functional theory (DFT) method, and the solvent effect was also considered and calculated by conductor-like polarizable calculation model (CPCM). Meanwhile, the hydrolysis process of the NH-tautomeric isomer, [Htrz][trans -RuCl4(4- H -1,2,4-triazole)(dmso- S)] 2, was also modeled and predicted by the same methods. The structural characteristics and the detailed energy profiles for the hydrolysis processes of two isomers have been obtained. The analysis of thermodynamic and kinetic characteristics of hydrolysis reaction suggests the following: for the first hydrolysis step, the Complex 1 has lower hydrolysis rate than the reported anticancer drug NAMI-A, and the result is in accordance with experimental one. However, Complex 1 has obviously higher hydrolysis rate than its isomer Complex 2, and the result was reasonably explained in theory. For the second hydrolysis step, the formation of cis -diaqua species is thermodynamic preferred to that of trans isomers. In addition, the trend in nucleophilic attack abilities (A) of hydrolysis products by pertinent biomolecules was revealed and predicted. © 2009 Wiley Periodicals, Inc. Int J Quantum Chem, 2010 [source] Evaluation of lignans and free and linked hydroxy-tyrosol and tyrosol in extra virgin olive oil after hydrolysis processesJOURNAL OF THE SCIENCE OF FOOD AND AGRICULTURE, Issue 5 2006Nadia Mulinacci Abstract We describe chemical hydrolytic procedures to evaluate the total amount of tyrosol and hydroxy-tyrosol free and/or linked to secoiridoidic molecules (acid hydrolysis). At the same time a rapid determination of the lignans in complex minor polar compound (MPC) extracts is proposed (alkaline hydrolysis). High-performance liquid chromatography/diode array detection (HPLC/DAD) and HPLC/MS were applied as reference methods to evaluate the quantitative results from the hydrolysis experiments. The optimized acid hydrolysis procedures were first applied to an oleuropein standard and then to MPC fractions extracted from several commercial extra virgin olive oils. The results confirm the applicability of the method, consisting in the acid hydrolysis of complex mixtures of secoiridoidic derivatives, to determine the antioxidant potential in terms of MPC. These data can contribute to forecasting the potential ageing resistance of an extra virgin olive oil in terms of antioxidant potency. Finally, alkaline hydrolysis allows confirmation and easy determination of the amount of lignans, especially in those MPC fractions which are particularly complex. Copyright © 2006 Society of Chemical Industry [source] Solubilisation of proteins from rayfish residues by endogenous and commercial enzymesJOURNAL OF THE SCIENCE OF FOOD AND AGRICULTURE, Issue 1 2004Laura Pastoriza Abstract The aim of the present study was to design methods for the digestion of fish proteins from processing wastes, leading to new possibilities for little-used species or those generating a significant volume of residues. Residues of rayfish (Raja clavata) were used for the solubilisation of protein by hydrolysis treatment. The kinetics of hydrolysis was studied using rayfish enzymes, either by autolysis of the protein in a triturate of the raw material or by application of a multi-enzyme preparation previously extracted from the viscera of the species. Their effectiveness was compared with that of two commercial enzymes, papain and pepsin. Optimum conditions of hydrolysis and enzymatic activity for digestion with rayfish enzymes were ascertained. The yield of material and the efficiency of digestion in each of the hydrolysis processes are reported. Copyright © 2003 Society of Chemical Industry [source] | ||||||||||||||||