			Home About us Contact

Glass Fabrics (glass + fabric)

Distribution by Scientific Domains

Chemistry	42%

Selected Abstracts

Innovative Catalysts for Oxidative Dehydrogenation in the Gas Phase , Metallic Short Fibers and Coated Glass Fabrics,

CHEMICAL ENGINEERING & TECHNOLOGY (CET), Issue 9 2005
R. Brüning
Abstract The catalytic activity of metallic short fibers with chosen alloy components and textures was investigated in the oxidative dehydrogenation (ODH) of propane to yield propene, and of isopropanol to yield acetone. The short fibers were synthesized using a melt extraction process and the properties of the fibers were intensely characterized. A correlation between the structure and the catalytic activity of the material was established. Optical microscopic, DSC, XRD, REM and EDX methods were used to characterize the fibers. Selective results of the dependency of the temperature on the propane conversion are presented in this work. A yield of more than 35,% propene is obtained at a propane conversion of 50,%. The ODH of isopropanol to acetone occurred with attractive yields of over 80,%. The results demonstrate the high innovative potential of the metal fiber materials. The use of coated glass fabrics as catalysts for the ODH and total oxidation of propane were also part of this investigation. [source]

Numerical simulation of the microscale impregnation in commingled thermoplastic composite yarns

ADVANCES IN POLYMER TECHNOLOGY, Issue 2 2010
R. Gennaro
Abstract The impregnation of a glass woven fabric with an amorphous polyethylene terephthalate copolymer (PET- g) matrix was investigated using a finite element (FE) model for interbundle and intrabundle flow of the matrix. Micrographs of samples obtained by film stacking of PET- g to impregnate the glass fabric have confirmed the occurrence of interbundle and intrabundle flow, taking place as separate steps. On the basis of this evidence, two different mechanisms for the fiber impregnation were postulated. The first flow process is associated with a macroscale interbundle impregnation, whereas the second is associated with microscale intrabundle impregnation. Two different FE models were developed to simulate the microscopic and macroscopic flow of the matrix, considering a large number of different random fiber arrangements. Both models could account for the non-Newtonian rheological behavior of the thermoplastic matrix. The microscale impregnation of fibers was simulated by using randomly spaced and nonoverlapping unidirectional filaments. The effect of the number of filaments and the number of random distributions necessary to achieve an adequate accuracy of the method was assessed. The results obtained from the simulation showed that at low pressures, the polymer melt exhibits Newtonian behavior, which makes it possible to predict the tow permeability by the Darcy law. A more difficult situation arises at high pressures because of the non-Newtonian behavior of the melt. This requires the introduction of a value for the permeability that is also dependent on the rheological properties of the melt. The same non-Newtonian behavior of the matrix was observed for macroscale impregnation of bundles. © 2010 Wiley Periodicals, Inc. Adv Polym Techn 29:122,130, 2010; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.20179 [source]

The effects of curing cycles on properties of the epoxy system 3221/RH glass fabric composites

POLYMER COMPOSITES, Issue 4 2008
Hong Xuhui
In this work, the epoxy system 3221 and its glass fabric laminates were thermally cured under different curing temperatures. The curing degree of the resin was increased with elevated reaction temperature. Dynamic mechanical analysis was performed on the laminate coupons and glass transition temperature (Tg) and relative stiffness (E,) of composites were measured before and after soaked in distilled water at 70°C. A shift in glass transition temperature to higher values and the splitting of the tan , curve were observed with extent of cure under dry conditions. Tg values shifted to lower temperatures after immersion. Under wet condition, the change in Tg1 was very small when the curing degree was up to 96%. The relative stiffness experienced a reduction both in initial modulus and the initial sharp drop temperature after immersion. It also suggested that the excessively high curing temperature (>130°C) had a negative effect on the retention of relative stiffness under wet condition. Both the interlaminar shear strength and dielectric properties of laminates were determined before and after immersion. The compared results demonstrated that the elevated curing temperature played a good influence on both of the properties before aged. However, for samples cured above 130°C, lower retention of interlaminar shear strength and poor dielectric properties were observed during immersion due to their higher moisture contents. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers [source]

Impact damage detection and degradation monitoring of wet GFRP composites using noncontact ultrasonics

POLYMER COMPOSITES, Issue 8 2009
K. Berketis
Two different non-crimp glass fabrics with a polyester resin were used to produce laminated plates that were subjected to low velocity impact testing using three impact energy levels. The plates were immersed in water at 65°C for up to 24 months. The effectiveness of a traditional water coupled and an air-coupled ultrasonic C-Scan system was assessed in terms of damage size evaluation at various time intervals. The conditioned impacted plates were retested statically in compression to determine the residual strength for evaluation of damage tolerance. Weight change measurements revealed an initial increase due to water diffusion, followed by an extended decrease due to matrix dissolution at long-term immersion times. The use of water coupled pulse-echo ultrasonics proved ineffective after long-term water immersion as damaged areas became ultrasound-invisible. The contrast between impact damaged areas and water diffused areas was restored with the air-coupled C-scan. The macroscopic damage size was not affected by the long-term water immersion and the overall weight change while the residual compression strength was seemed to be dependent on the time of immersion and the size of the pre-existing impact damage. Calibrating the air-coupled system to a dry condition specimen, a good qualitative and quantitative indication of the degraded state of water immersed plates was obtained. This monitoring system for the degradation process seems to be very promising. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers [source]

Polyester composites reinforced with noncrimp stitched glass fabrics: Experimental characterization of composites and investigation on the interaction between glass fiber and polyester matrix

POLYMER COMPOSITES, Issue 3 2008
Volkan Cecen
The primary purpose of the study was to investigate the anisotropic behavior of different noncrimp stitched fabric reinforced polyester composites. The effects of geometric variables on composite structural integrity and strength are illustrated. Hence, tensile, three-point bending flexural and short beam shear tests were conducted up to failure on specimens strengthened with different layouts of fibrous plies in noncrimp stitched fabric. The remark, based on the observations while tensile testing, is that the stress,strain curves of polyester based composites were linear in the direction of fibers. However, in the matrix dominated orientations nonlinear relation between the stress and the strain was observed. Another aim of the present work was to investigate the interaction between glass fiber and polyester matrix. The experiments, in conjunction with scanning electron photomicrographs of fractured surfaces of composites, were interpreted in an attempt to explain the interaction between glass fiber and polyester and were interpreted in an attempt to explain the instability of polyester resin,glass fiber interfaces. It was concluded that the polymer was either deposited between adjacent fibers or as widely separated islands on the fiber surface. Infrared spectra of the cured polyester and its glass fiber composite were obtained by Fourier transform infrared spectroscopy. POLYM. COMPOS., 2008. © 2007 Society of Plastics Engineers [source]

Investigation of basalt fiber composite aging behavior for applications in transportation,

POLYMER COMPOSITES, Issue 5 2006
Qiang Liu
New materials such as basalt fiber offer the promise of innovative applications in transportation because of documented strengths (V. Ramakrishnan, N.S. Tolmare, and V. Brik, "NCHRP-IDEA Program Project Final Report, " Transportation Research Board, Washington, DC, (1998)). Previously, we found that mechanical properties of basalt twill fabric-reinforced polymer composites were comparable to composites reinforced with glass fabrics of similar structures [Q. Liu, M.T. Shaw, R.S. Parnas, and A.M. McDonnell, Polymer Composites, 27(1), 41 (2006)]. Use in transportation also requires knowledge of environmental durability. This study reports the tolerance of basalt-fiber-reinforced polymer composites to salt water immersion, moisture absorption, temperature, and moisture cycling. Parallel tests were conducted for the corresponding glass-reinforced polymer composites. Aging for 240 days in salt water or water decreased the Young's modulus and tensile strength of basalt composites slightly but significantly (p < 0.05). Freeze-thaw cycling up to 199 cycles did not change the shear strength significantly, but aging in hot (40°C) salt water or water did decrease the shear strength of basalt composites (p < 0.05). The aging results indicate that the interfacial region in basalt composites may be more vulnerable to damage than that in glass composites. POLYM. COMPOS., 27:475,483, 2006. © 2006 Society of Plastics Engineers [source]