Home About us Contact
|
Home About us Contact | ||
|
|
||
Flammability Properties (flammability + property)
Selected AbstractsA flammability performance comparison between synthetic and natural clays in polystyrene nanocompositesFIRE AND MATERIALS, Issue 4 2005Alexander B. Morgan Abstract Polymer-clay nanocomposites are a newer class of flame retardant materials of interest due to their balance of mechanical, thermal and flammability properties. Much more work has been done with natural clays than with synthetic clays for nanocomposite flammability applications. There are advantages and disadvantages to both natural and synthetic clay use in a nanocomposite, and some of these, both fundamental and practical, will be discussed in this paper. To compare natural and synthetic clays in regards to polymer flammability, two clays were used. The natural clay was a US mined and refined montmorillonite, while the synthetic clay was a fluorinated synthetic mica. These two clays were used as inorganic clays for control experiments in polystyrene, and then converted into an organoclay by ion exchange with an alkyl ammonium salt. The organoclays were used to synthesize polystyrene nanocomposites by melt compounding. Each of the formulations was analysed by X-ray diffraction (XRD), thermogravimetric analysis (TGA) and transmission electron microscopy (TEM). Flammability performance was measured by cone calorimeter. The data from the experiments show that the synthetic clay does slightly better at reducing the heat release rate (HRR) than the natural clay. However, all the samples, including the inorganic clay polystyrene microcomposites, showed a decreased time to ignition, with the actual nanocomposites showing the most marked decrease. The reason for this is postulated to be related to the thermal instability of the organoclay (via the quaternary alkyl ammonium). An additional experiment using a more thermally stable organoclay showed a time to ignition identical to that of the base polymer. Finally, it was shown that while polymer-clay nanocomposites (either synthetic or natural clay based) greatly reduce the HRR of a material, making it more fire safe, they do not provide ignition resistance by themselves, at least, at practical loadings. Specifically, the cone calorimeter HRR curve data appear to support that these nanocomposites continue to burn once ignited, rather than self-extinguish. Copyright © 2004 John Wiley & Sons, Ltd. [source] Properties of polypropylene/aluminum trihydroxide composites containing nanosized organoclayPOLYMER ENGINEERING & SCIENCE, Issue 12 2005Noora Ristolainen Montmorillonite is a promising substitute for aluminum trihydroxide in flame-retardant polypropylene/aluminum trihydroxide (PP/ATH) composites. Study was made of the partial substitution of organoclay for ATH in PP/ATH composites. The total concentration of filler was kept at 30 wt%. The composites were compatibilized with two types of compatibilizer: commercial maleic anhydride functionalized polypropylene (PP- g -MA) and hydroxyl-functionalized polypropylene (PP- co -OH) prepared with metallocene catalyst. The effect of compatibilization on the morphology was studied by the transmission electron microscopy and the scanning electron microscopy. Mechanical properties were characterized by tensile and impact measurements, and flammability properties with a cone calorimeter. Addition of compatibilizer and stearic acid (SA) treatment of the ATH particles contributed to the dispersion of the fillers. Both compatibilizers produced organoclay with exfoliated structure and improved adhesion between the fillers and the matrix. Toughness improved and decomposition and flammability were reduced. POLYM. ENG. SCI. 45:1568,1575, 2005. © 2005 Society of Plastics Engineers [source] Flammability and thermal stability studies of ABS/Montmorillonite nanocompositePOLYMER INTERNATIONAL, Issue 6 2003Shaofeng Wang Abstract Acrylonitrile,butadiene,styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X-ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated,delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated,intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry [source] Effects of cell structure and density on the properties of high performance polyimide foams,,POLYMERS FOR ADVANCED TECHNOLOGIES, Issue 2-3 2005Martha K. Williams Abstract Activity at the NASA Langley Research Center (LaRC) has focused on developing low density polyimide foam and foam structures which are made using monomeric solutions or salt solutions formed from the reaction of a dianhydride and diamine dissolved in a mixture of foaming agents and alkyl alcohol at room temperature. Monomer blends may be used to make a variety of polyimide foams with varying properties. The first foaming process developed consisted of thermal cycling the polymer precursor residuum and allowing the inflation of the particles to interact to create the foam. This process has resulted in foam structures with higher percentages of open cell content. Another innovative foaming process has been developed that begins with partially inflated microspheres, "friable balloons", with incomplete polymer molecular weight gain, which when fully cured into a foam results in more closed cell structures. In a research study performed by NASA Kennedy Space Center (KSC) and LaRC, two closely related polyimide foams, TEEK-H series and TEEK-L series, (4,4,-oxydiphthalic anhydride/3,4,-oxydianiline and 3,3,,4,4,-benzophenonetetracarboxylic acid dianhydride/4,4,-oxydianiline) were investigated for density effects and closed versus open cell effects on the thermal, mechanical, and flammability properties. Thermal conductivity data under the full range of vacuum pressures indicate that these materials are effective insulators under cryogenic conditions. Contributing factors such as cell content, density, and surface area were studied to determine the effects on thermal conductivity. Cone calorimetry data indicated decreased peak heat release rates for the closed cell system, TEEK-H friable balloons, compared to the TEEK foams with higher open cell content. Mechanical properties including tensile strength and compressive strength indicated that the materials have good structural integrity. Foams with more open cell content resulted in greater tensile and compressive strengths than the closed cell foams. The maximum closed cell content achieved in the "friable balloon" system was 78% at a foam density of 0.048 gm/cm3. Published in 2005 by John Wiley & Sons, Ltd. [source] | ||||||||||