Home About us Contact
|
Home About us Contact | ||
|
|
||
Flowable Resin Composite (flowable + resin_composite)
Selected AbstractsBonding of fractured permanent central incisor crown following radiographic localization of the tooth fragment in the lower lip: a case reportDENTAL TRAUMATOLOGY, Issue 5 2010Gabriela Ferrari Da Silva Schwengber The trauma also resulted in a cut on his mentum. Radiographic examination revealed the fractured tooth fragment embedded in the lower lip. The fractured tooth, with incomplete root formation, was treated endodontically and received a temporary restoration. After 15 days, the temporary restoration was removed and the fractured tooth fragment was etched with 37% phosphoric acid. A bonding system was then applied to the etched-fractured tooth surface without polymerization. The same bonding procedure was carried out on the tooth fragment. A layer of flowable resin composite was applied to the fragment, which was positioned on the remaining tooth. The resin composite was then polymerized, finished, and polished. [source] Evaluation of success in the reattachment of coronal fracturesDENTAL TRAUMATOLOGY, Issue 2 2008Yucel Yilmaz This study was conducted on 11 children (six girls and five boys; age range: 8,13 years). Before the treatment, the teeth were evaluated clinically and radiographically. The broken incisal part was directly reattached to the remaining tooth part with flowable resin composite. Thereafter, with the purpose of obtaining optimal esthetics and function, along the fracture line an external ,double chamfer' in the shape of a V was created and then covered with resin composite. During the follow-up (1,24 months) after the treatment, the teeth were evaluated clinically and/or radiographically with regard to periodontal, pulpal, coronal, color harmony of the fragments, and occlusion. In addition, the restored teeth were assessed in terms of parental,patient ratings of satisfaction. Both clinically and radiographically, no pathology was reported and all the restorations were successful. Moreover, the mean scores of parental,patient satisfaction were reported as ,satisfied, very-satisfied.' [source] Bonding characteristics of newly developed all-in-one adhesivesJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 2 2007S. K. Sidhu Abstract This study evaluated the microtensile bond strength and the interfacial morphology of newer adhesives. The occlusal surfaces of extracted teeth were ground flat for random allocation to four equal groups. Resin composite was bonded to each surface using either Clearfil SE Bond [SEB], Clearfil Protect Bond [PB], G-Bond [GB], or an experimental adhesive, SSB-200 [SSB]. After storage for 24 h in water at 37°C, they were sectioned into beams (cross-sectional area 1 mm2) for microtensile bond strength testing (,TBS) at a crosshead speed of 1 mm/min. The load at failure of each was recorded; the data were analyzed by one-way ANOVA and Games Howell tests. The surfaces of the fractured specimens were observed using SEM. For the ultra-morphology of the interface, the occlusal surfaces of four more teeth were prepared as before and a thin layer of flowable resin composite was bonded to each surface using one of the four adhesives. The mean ,TBS ranged from 39.68 MPa (GB) to 64.97 MPa (SEB). There were no statistical differences between SEB and SSB, or between PB and GB (p > 0.05). The ,TBS of SEB and SSB were significantly greater than that of PB and GB (p < 0.05). SEMs of the fractured surfaces revealed a mixed (cohesive/interfacial) failure. TEM examination highlighted differences in the hybrid layer; SEB had a thicker layer than the others. In conclusion, the newer all-in-one adhesives produced a thin hybrid layer but varied in their bond strengths. The 2-step self-etching adhesives do not necessarily produce higher bond strengths than that of the all-in-one systems. © 2006 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2007 [source] Effect of Aging on Coronal Microleakage in Access Cavities through Metal Ceramic Crowns Restored with Resin CompositesJOURNAL OF PROSTHODONTICS, Issue 5 2010Ali Abdullah Alwan Al-Maqtari BDS Abstract Purpose: The purpose of this in vitro study was to determine if packable resin composite with/without flowable resin composite has the ability to prevent coronal leakage in restored endodontic access openings following aging. Materials and Methods: Eighty simulated standardized access cavities of metal-ceramic crowns were fabricated and fixed on Vitrebond cavities filled with an epoxy resin. The specimens were randomly divided into two main groups: (1) Group A,Access cavities filled with only packable composite (Filtek P60); (2) Group B,Access cavities filled with Filtek P60 and a flowable composite (Filtek Z350) as liner. Each main group was further subdivided randomly into four subgroups according to water storage and thermocycling periods. All specimens were immersed in blue ink solution for 24 hours and then sectioned into quadrants. The extension of blue ink along the metal-ceramic crown/composite resin interface was measured linearly using image analyzer and then analyzed by three-way ANOVA and independent t -test with a Mann-Whitney test. The level of significance was set at p < 0.05. Results: All tested subgroups demonstrated different levels of microleakage. There was no significant difference related to restorative technique; however, there was a significant difference related to water storage and thermocycling. Conclusions: All tested techniques and materials in this study showed microleakage. Packable composite while a flowable liner showed a marginally better result than packable composite alone. Excessive thermocycling resulted in significant differences among the test groups. [source] | ||||||||||