Home About us Contact | |||
Flour Composites (flour + composite)
Kinds of Flour Composites Selected AbstractsThermoplastic silicone elastomer lubricant in extrusion of polypropylene wood flour compositesADVANCES IN POLYMER TECHNOLOGY, Issue 2 2007Velichko Hristov Abstract A possibility of using a thermoplastic silicone elastomer (TPSE) for reduction of surface defects in the extrusion of wood-filled metallocene polypropylene (mPP) has been investigated in this work. A capillary rheometer and a single-screw extruder have been utilized to study the effect of the additive on the extrudate distortions. Maleated syndiotactic metallocene polypropylene was also used as an adhesion promoter in mPP/wood flour composites. At loadings of 50 wt% wood flour in the mPP, the extrudates come out of the die with significant tearing and surface roughness. The surface rupture mechanism is similar to that of sharkskin in neat polymers; however, the defect is much more exaggerated in the case of wood fiber-filled composites. It was found that TPSE at low concentrations (1 wt%) was able to reduce or even completely eliminate extrudate surface tearing. Increasing the extrusion speed yielded better results. Addition of a coupling agent also provides improvement in the extrudate appearance. © 2007 Wiley Periodicals, Inc. Adv Polym Techn 26:100,108, 2007; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.20090 [source] Crystallization and melting behavior of HDPE in HDPE/teak wood flour composites and their correlation with mechanical propertiesJOURNAL OF APPLIED POLYMER SCIENCE, Issue 4 2010Kamini Sewda Abstract The nonisothermal crystallization behavior and melting characteristics of high-density polyethylene (HDPE) in HDPE/teak wood flour (TWF) composites have been studied by differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WAXD) methods. Composite formulations of HDPE/TWF were prepared by varying the volume fraction (,f) of TWF (filler) from 0 to 0.32. Various crystallization parameters evaluated from the DSC exotherms were used to study the nonisothermal crystallization behavior. The melting temperature (Tm) and crystallization temperature (Tp) of the composites were slightly higher than those of the neat HDPE. The enthalpy of melting and crystallization (%) decrease with increase in the filler content. Because the nonpolar polymer HDPE and polar TWF are incompatible, to enhance the phase interaction maleic anhydride grafted HDPE (HDPE-g-MAH) was used as a coupling agent. A shift in the crystallization and melting peak temperatures toward the higher temperature side and broadening of the crystallization peak (increased crystallite size distribution) were observed whereas crystallinity of HDPE declines with increase in ,f in both DSC and WAXD. Linear correlations were obtained between crystallization parameters and tensile and impact strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Wood/plastic composites co-extruded with multi-walled carbon nanotube-filled rigid poly(vinyl chloride) cap layerPOLYMER INTERNATIONAL, Issue 5 2010Shan Jin Abstract Wood/plastic composites (WPCs) can absorb moisture in a humid environment due to the hydrophilic nature of the wood in the composites, making products susceptible to microbial growth and loss of mechanical properties. Co-extruding a poly(vinyl chloride) (PVC)-rich cap layer on a WPC significantly reduces the moisture uptake rate, increases the flexural strength but, most importantly, decreases the flexural modulus compared to uncapped WPCs. A two-level factorial design was used to develop regression models evaluating the statistical effects of material compositions and a processing condition on the flexural properties of co-extruded rigid PVC/wood flour composites with the ultimate goal of producing co-extruded composites with better flexural properties than uncapped WPCs. Material composition variables included wood flour content in the core layer and carbon nanotube (CNT) content in the cap layer of the co-extruded composites, with the processing temperature profile for the core layer as the only processing condition variable. Fusion tests were carried out to understand the effects of the material compositions and processing condition on the flexural properties. Regression models indicated all main effects and two powerful interaction effects (processing temperature/wood flour content and wood flour content/CNT content interactions) as statistically significant. Factors leading to a fast fusion of the PVC/wood flour composites in the core layer, i.e. low wood flour content and high processing temperature, were effective material composition and processing condition parameters for improving the flexural properties of co-extruded composites. Reinforcing the cap layer with CNTs also produced a significant improvement in the flexural properties of the co-extruded composites, insensitive to the core layer composition and the processing temperature condition. Copyright © 2009 Society of Chemical Industry [source] |