Home About us Contact
|
Home About us Contact | ||
|
|
||
Fiber-reinforced Composites (fiber-reinforced + composite)
Selected AbstractsEvaluation of a new fiber-reinforced resin compositeJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2006S. Suzuki Abstract Efficacy of the usage of an experimental fiber-reinforced composite (FRC) on mechanical properties of an indirect composite was investigated by means of three-point bending and Charpy impact tests. Bond strength between the FRC and the indirect composite was also evaluated by tensile testing. The FRC consisted of a matrix resin with 25% silanized milled glass fiber (11-,m diameter, 150-,m length) and 5% colloidal silica. The values of strain of proportional limit, total strain, and fracture energy of the FRC during the bending test (1.2%, 10.4%, and 41.6 × 10,3 J) were significantly higher than those of the indirect composite (0.1%, 2.5%, and 11.9 × 10,3 J). The impact strengths of the 1-mm specimens with FRC ranged from 15.2 to 15.9 kJ/m2, and were significantly higher than that of the control (3.1 kJ/m2). The 2-mm specimens showed significant difference from the control when the FRC thickness was equal or greater than 0.5 mm. The bond strength after the thermocycling was 15.2 MPa, and all of the specimens exhibited cohesive fracture inside the indirect composite. Based upon the results, it was concluded that the FRC tested in this study improved toughness and impact resistance of the indirect composite. The interfacial bonding between the FRC and the indirect composite was strong enough to prevent delamination. © 2005 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2006 [source] A Global Approach to Fiber nD Architectures and Self-Sealing Matrices: From Research to ProductionINTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, Issue 2 2005F. A. Christin Thermostructural composites (TSC) improvement is one of the key factors to ensure future competitiveness of aeronautical and space engines. The TSC technology developed in Snecma Propulsion Solide is based on continuous fiber-reinforced composites and carbon or ceramics matrices deposited by chemical vapor infiltration. This article presents a status of the latest improvements for cost savings of composite reinforcements (so-called texture) and specific matrices developed to increase both durability and temperature capability of previous ceramic composites, operating in oxidative environments. [source] Fiber breakage and dispersion in carbon-fiber-reinforced nylon 6/clay nanocompositesJOURNAL OF APPLIED POLYMER SCIENCE, Issue 3 2007Hu Zhou Abstract In this paper, short carbon-fiber-reinforced nylon 6/clay nanocomposites are prepared via melt compounding, and fiber breakage and dispersion during processing are studied. The influences of clay and processing conditions on fiber breakage and dispersion are taken into consideration. It is found that the presence of organoclay can improve fiber dispersion, which is due to dispersion at the nanoscale of exfoliated clay sheets with large aspect ratio. The bimodal distribution of fiber length is observed in fiber-reinforced nanocomposites, which is similar to that in conventional fiber-reinforced composites. The improvement of fiber breakage at moderate organoclay loadings is also observed, which is ascribed to the rheological and lubricating effects induced by organoclay. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007 [source] Hydrothermal and mechanical stresses degrade fiber,matrix interfacial bond strength in dental fiber-reinforced compositesJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2006Serge Bouillaguet Abstract Fiber-reinforced composites (FRCs) show great promise as long-term restorative materials in dentistry and medicine. Recent evidence indicates that these materials degrade in vivo, but the mechanisms are unclear. The objective of this study was to investigate mechanisms of deterioration of glass fiber,polymer matrix bond strengths in dental fiber-reinforced composites during hydrothermal and mechanical aging. Conventional three-point bending tests on dental FRCs were used to assess flexural strengths and moduli. Micro push-out tests were used to measure glass fiber,polymer matrix bond strengths, and nanoindentation tests were used to determine the modulus of elasticity of fiber and polymer matrix phases separately. Bar-shaped specimens of FRCs (EverStick, StickTech, and Vectris Pontic, Ivoclar-Vivadent) were either stored at room temperature, in water (37 and 100°C) or subjected to ageing (106 cycles, load: 49 N), then tested by three-point bending. Thin slices were prepared for micro push-out and nanoindentation tests. The ultimate flexural strengths of both FRCs were significantly reduced after aging (p < 0.05). Both water storage and mechanical loading reduced the interfacial bond strengths of glass fibers to polymer matrices. Nanoindentation tests revealed a slight reduction in the elastic modulus of the EverStick and Vectris Pontic polymer matrix after water storage. Mechanical properties of FRC materials degrade primarily by a loss of interfacial bond strength between the glass and resin phases. This degradation is detectable by micro push-out and nanoindentation methods. © 2005 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2006 [source] Impression creep of PMR-15 resin at elevated temperaturesPOLYMER ENGINEERING & SCIENCE, Issue 1 2010Rong Chen The polyimides formed from the polymerization of monomeric-reactants (PMR) approach have been increasingly used as matrix materials in fiber-reinforced composites on aerospace and space structures for high temperature applications. The performance of PMR-based structures depends on the mechanical durability of PMR resins at elevated temperatures, including creep and stress relaxation. In this work, the creep behavior of PMR-15 resin was studied using the impression technique in the temperature range of 563,613 K and the punching stress range of 76,381 MPa. It was found that there existed a steady state creep for the creep tests performed at temperatures of 563 K and higher, from which a constant impression velocity was calculated. The steady state impression velocity increased with temperature and punching stress with the stress exponent in the range of 1.5,2.2. The average of the apparent activation energy of the PMR-15 was calculated as 122.7 ± 6.1 kJ/mol. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers [source] Nanofiller-reinforced polymer nanocompositesPOLYMERS FOR ADVANCED TECHNOLOGIES, Issue 8 2008J. Njuguna Abstract In this work, the technology of nano- and micro-scale particle reinforcement concerning various polymeric fiber-reinforced systems including polyamides (PAs), polyesters, polyurethanes (PUs), polypropylenes (pps), and high-performance/temperature engineering polymers such as polyimide (PI), poly(ether ether ketone) (PEEK), polyarylacetylene (PAA), and poly p -phenylene benzobisoxazole (PBO) is reviewed. When the diameters of polymer fiber materials are shrunk from micrometers to submicrons or nanometers, there appear several unique characteristics such as very large surface area to volume ratio (this ratio for a nanofiber can be as large as 103 times of that of a microfiber), flexibility in surface functionalities and superior mechanical performance (such as stiffness and tensile strength) compared to any other known form of the material. While nanoparticle reinforcement of fiber-reinforced composites has been shown to be a possibility, much work remains to be performed in order to understand how nanoreinforcement results in dramatic changes in material properties. The understanding of these phenomena will facilitate their extension to the reinforcement of more complicated anisotropic structures and advanced polymeric composite systems. Copyright © 2008 John Wiley & Sons, Ltd. [source] Flammability and fire resistance of composites reinforced by natural fibersPOLYMERS FOR ADVANCED TECHNOLOGIES, Issue 6 2008Ryszard Koz, owski Abstract Natural fiber-reinforced composites are more and more frequently applied to building industry and transportation. Therefore, the knowledge of their behavior during fire is of high importance. Flammability is one of very important parameters that often limits the application of composites to a given area. It is well-known that addition of lignocellulosic fibers to polymer changes mechanical properties of the product obtained. However, little information is available on their fire performance. The purpose of this review was to obtain fire performance data for several types of composites reinforced by lignocellulosic fibers. Copyright © 2008 John Wiley & Sons, Ltd. [source] | ||||||||||