Home About us Contact
|
Home About us Contact | ||
|
|
||
Fabrication Process (fabrication + process)
Selected AbstractsFabrication of enclosed SU-8 tips for electrospray ionization-mass spectrometryELECTROPHORESIS, Issue 24 2005Santeri Tuomikoski Dr. Abstract We describe a novel electrospray tip design for MS which is fabricated completely out of SU-8 photoepoxy. A three-layer SU-8 fabrication process provides fully enclosed channels and tips. The tip shape and alignment of all SU-8 layers is done lithographically and is therefore very accurate. Fabrication process enables easy integration of additional fluidic functions on the same chip. Separation channels can be made with exactly the same process. Fluidic inlets are made in SU-8 during the fabrication process and no drilling or other postprocessing is needed. Channels have been fabricated and tested in the size range of 10,,m×10,,m,50,,m×200,,m. Mass spectrometric performance of the tips has been demonstrated with both pressure-driven flow and EOF. SU-8 microtips have been shown to produce stable electrospray with EOF in a timescale of tens of minutes. With pressure driven flow stable spray is maintained for hours. Taylor cone was shown to be small in volume and well defined even with the largest channel cross section. The spray was also shown to be well directed with our tip design. [source] Regular Arrays of Microdisk Electrodes: Numerical Simulation as an Optimizing Tool to Maximize the Current Response and Minimize the Electrode Area UsedELECTROANALYSIS, Issue 23 2006Francois Abstract Microdisk electrode arrays constitute an interesting tool for electroanalysis and electrocatalysis due to their increased sensitivity and excellent limits of detection. We first demonstrate that a 2-dimensional simulation based on the diffusion domain approximation can be used to simulate the response of such electrochemical systems and therefore improve their design and fabrication process. Second, we report data showing the peak current response for arrays at three typically employed voltage scan rate as a function of the number of disks per unit area and their radii. [source] Simply and reliably integrating micro heaters/sensors in a monolithic PCR-CE microfluidic genetic analysis systemELECTROPHORESIS, Issue 8 2009Runtao Zhong Abstract A novel fabrication process was presented to construct a monolithic integrated PCR-CE microfluidic DNA analysis system as a step toward building a total genetic analysis microsystem. Microfabricated Titanium/Platinum (Ti/Pt) heaters and resistance temperature detectors (RTDs) were integrated on the backside of a bonded glass chip to provide good thermal transfer and precise temperature detection for the drilled PCR-wells. This heater/RTD integration procedure was simple and reliable, and the resulting metal layer can be easily renewed when the Ti/Pt layer was damaged in later use or novel heater/RTD design was desired. A straightforward "RTD-calibration" method was employed to optimize the chip-based thermal cycling conditions. This method was convenient and rapid, comparing with a conventional RTD-calibration/temperature adjustment method. The highest ramping rates of 14°C/s for heating and 5°C/s for cooling in a 3-,L reaction volume allow 30 complete PCR cycles in about 33,min. After effectively passivating the PCR-well surface, successful ,-phage DNA amplifications were achieved using a two- or three-temperature cycling protocol. The functionality and performance of the integrated microsystem were demonstrated by successful amplification and subsequent on-line separation/sizing of ,-phage DNA. A rapid assay for Hepatitis B virus, one of the major human pathogens, was performed in less than 45,min, demonstrating that the developed PCR-CE microsystem was capable of performing automatic and high-speed genetic analysis. [source] Fabrication of enclosed SU-8 tips for electrospray ionization-mass spectrometryELECTROPHORESIS, Issue 24 2005Santeri Tuomikoski Dr. Abstract We describe a novel electrospray tip design for MS which is fabricated completely out of SU-8 photoepoxy. A three-layer SU-8 fabrication process provides fully enclosed channels and tips. The tip shape and alignment of all SU-8 layers is done lithographically and is therefore very accurate. Fabrication process enables easy integration of additional fluidic functions on the same chip. Separation channels can be made with exactly the same process. Fluidic inlets are made in SU-8 during the fabrication process and no drilling or other postprocessing is needed. Channels have been fabricated and tested in the size range of 10,,m×10,,m,50,,m×200,,m. Mass spectrometric performance of the tips has been demonstrated with both pressure-driven flow and EOF. SU-8 microtips have been shown to produce stable electrospray with EOF in a timescale of tens of minutes. With pressure driven flow stable spray is maintained for hours. Taylor cone was shown to be small in volume and well defined even with the largest channel cross section. The spray was also shown to be well directed with our tip design. [source] A microfabricated hybrid device for DNA sequencingELECTROPHORESIS, Issue 21 2003Shaorong LiuArticle first published online: 6 NOV 200 Abstract We have created a hybrid device of a microfabricated round-channel twin-T injector incorporated with a separation capillary in order to extend the straight separation distance for high speed and long readlength DNA sequencing. Semicircular grooves on glass wafers are obtained using a photomask with a narrow line-width and a standard isotropic photolithographic etching process. Round channels are made when two etched wafers are face-to-face aligned and bonded. A two-mask fabrication process has been developed to make channels of two different diameters. The twin-T injector is formed by the smaller channels whose diameter matches the bore of the separation capillary, and the "usual" separation channel, now called the connection channel, is formed by the larger ones whose diameter matches the outer diameter of the separation capillary. The separation capillary is inserted through the connection channel all the way to the twin-T injector to allow the capillary bore flush with the twin-T injector channels. The total dead-volume of the connection is estimated to be , 5 pL. To demonstrate the efficiency of this hybrid device, we have performed four-color DNA sequencing on it. Using a 200 ,m twin-T injector coupled with a separation capillary of 20 cm effective separation distance, we have obtained readlengths of 800 plus bases at an accuracy of 98.5% in 56 min, compared to about 650 bases in 100 min on a conventional 40 cm long capillary sequencing machine under similar conditions. At an increased separation field strength and using a diluted sieving matrix, the separation time has been reduced to 20 min with a readlength of 700 bases at 98.5% base-calling accuracy. [source] Sequencing of real-world samples using a microfabricated hybrid device having unconstrained straight separation channelsELECTROPHORESIS, Issue 21 2003Shaorong Liu Abstract We describe a microfabricated hybrid device that consists of a microfabricated chip containing multiple twin-T injectors attached to an array of capillaries that serve as the separation channels. A new fabrication process was employed to create two differently sized round channels in a chip. Twin-T injectors were formed by the smaller round channels that match the bore of the separation capillaries and separation capillaries were incorporated to the injectors through the larger round channels that match the outer diameter of the capillaries. This allows for a minimum dead volume and provides a robust chip/capillary interface. This hybrid design takes full advantage, such as sample stacking and purification and uniform signal intensity profile, of the unique chip injection scheme for DNA sequencing while employing long straight capillaries for the separations. In essence, the separation channel length is optimized for both speed and resolution since it is unconstrained by chip size. To demonstrate the reliability and practicality of this hybrid device, we sequenced over 1000 real-world samples from Human Chromosome 5 and Ciona intestinalis, prepared at Joint Genome Institute. We achieved average Phred20 read of 675 bases in about 70 min with a success rate of 91%. For the similar type of samples on MegaBACE 1000, the average Phred20 read is about 550,600 bases in 120 min separation time with a success rate of about 80,90%. [source] Porous Porphyrin Nanoarchitectures on SurfacesEUROPEAN JOURNAL OF INORGANIC CHEMISTRY, Issue 24 2010Rie Makiura Abstract Controlling the size and the growth direction of porous hybrid objects , metal,organic frameworks (MOFs) or porous coordination polymers (PCPs) , at the nanoscale is a critical issue for enabling their use in a number of potential applications that have arisen from the current remarkable activity in studying such porous materials. This microreview describes the recent progress in the design, growth, and characterization of multidimensional nanoarchitectures by employing porphyrin-based components. The versatility of the sequential bottom-up fabrication process, which uses multitopic molecular building units assembled by appropriately chosen linkers, is suitable to be extended to the formation of a rich variety of nanostructures endowed with pores on surfaces. [source] Surface Nanometer-Scale Patterning in Realizing Large-Scale Ordered Arrays of Metallic Nanoshells with Well-Defined Structures and Controllable PropertiesADVANCED FUNCTIONAL MATERIALS, Issue 15 2010Shikuan Yang Abstract Surface patterns of nanoshell arrays play an important role in diverse applications including surface-enhanced Raman scattering (SERS) sensors, lithium-ion batteries, solar cells, and optical devices. This paper describes an innovative surface nanopatterning technique for realizing large-scale ordered arrays of metallic spherical nanoshells with well-defined structures. Ag nanoshell arrays are prepared using polystyrene sphere templates by an electrophoretic process in Ag colloidal solutions. The fabricated Ag nanoshell arrays have a high controllability of the structural parameters, including the diameter, the surface roughness, and the intershell spacing, giving rise to the tunable properties of nanoshell arrays. As an example, tunable SERS and localized surface plasmon resonance of the nanoshell arrays are demonstrated by controlling the structural parameters. The surface nanopatterning technique shown in this paper is a general fabrication process in achieving not only metallic nanoshell arrays, but also nanoshell arrays of semiconductors and metallic oxides. [source] Assessment of fire protection performance of water mist applied in exhaust ducts for semiconductor fabrication processFIRE AND MATERIALS, Issue 5 2005Yi-Liang Shu Abstract Fume exhaust pipes used in semiconductor facilities underwent a series of fire tests to evaluate the performance of a water mist system. The parameters considered were the amount of water that the mist nozzles used, the air flow velocity, the fire intensity and the water mist system operating pressure. In order to make a performance comparison, tests were also performed with a standard sprinkler system. The base case served as a reference and applied a single water mist nozzle (100 bar operating pressure, 7.3 l/min water volume flux and 200 µm mean droplet size) installed in the pipe (60 cm in diameter) subjected to a 350°C air flow with an average velocity of 2 m/s. In such a case, the temperature in the hot flow dropped sharply as the water mist nozzle was activated and reached a 60°C saturation point. Under the same operating conditions, four mist nozzles were applied, and made no further contribution to reducing the fire temperature compared with the case using only a single nozzle. Similar fire protection performances to that in the base case were still retained when the exhaust flow velocity increased to 3 m/s and the inlet air temperature was increased to 500°C due to a stronger input fire scenario, respectively. Changing to a water mist system produced a better performance than a standard sprinkler. With regard to the effect of operating pressure of water mist system, a higher operating pressure can have a better performance. The results above indicate that the droplet size in a water-related fire protection system plays a critical role. Copyright © 2005 John Wiley & Sons, Ltd. [source] Characterization of a Novel Fiber Composite Material for Mechanotransduction Research of Fibrous Connective TissuesADVANCED FUNCTIONAL MATERIALS, Issue 5 2010Hazel R. C. Screen Abstract Mechanotransduction is the fundamental process by which cells detect and respond to their mechanical environment, and is critical for tissue homeostasis. Understanding mechanotransduction mechanisms will provide insights into disease processes and injuries, and may support novel tissue engineering research. Although there has been extensive research in mechanotransduction, many pathways remain unclear, due to the complexity of the signaling mechanisms and loading environments involved. This study describes the development of a novel hydrogel-based fiber composite material for investigating mechanotransduction in fibrous tissues. By encapsulating poly(2-hydroxyethyl methacrylate) rods in a bulk poly(ethylene glycol) matrix, it aims to create a micromechanical environment more representative of that seen in vivo. Results demonstrated that collagen-coated rods enable localized cell attachment, and cells are successfully cultured for one week within the composite. Mechanical analysis of the composite indicates that gross mechanical properties and local strain environments could be manipulated by altering the fabrication process. Allowing diffusion between the rods and surrounding matrix creates an interpenetrating network whereby the relationships between shear and tension are altered. Increasing diffusion enhances the shear bond strength between rods and matrix and the levels of local tension along the rods. Preliminary investigation into fibroblast mechanotransduction illustrates that the fiber composite upregulates collagen I expression, the main protein in fibrous tissues, in response to cyclic tensile strains when compared to less complex 2D and 3D environments. In summary, the ability to create and manipulate a strain environment surrounding the fibers, where combined tensile and shear forces uniquely impact cell functions, is demonstrated. [source] Time Controlled Protein Release from Layer-by-Layer Assembled Multilayer Functionalized Agarose HydrogelsADVANCED FUNCTIONAL MATERIALS, Issue 2 2010Sumit Mehrotra Abstract Axons of the adult central nervous system exhibit an extremely limited ability to regenerate after spinal cord injury. Experimentally generated patterns of axon growth are typically disorganized and randomly oriented. Support of linear axonal growth into spinal cord lesion sites has been demonstrated using arrays of uniaxial channels, templated with agarose hydrogel, and containing genetically engineered cells that secrete brain-derived neurotrophic factor (BDNF). However, immobilizing neurotrophic factors secreting cells within a scaffold is relatively cumbersome, and alternative strategies are needed to provide sustained release of BDNF from templated agarose scaffolds. Existing methods of loading the drug or protein into hydrogels cannot provide sustained release from templated agarose hydrogels. Alternatively, here it is shown that pH-responsive H-bonded poly(ethylene glycol)(PEG)/poly(acrylic acid)(PAA)/protein hybrid layer-by-layer (LbL) thin films, when prepared over agarose, provided sustained release of protein under physiological conditions for more than four weeks. Lysozyme, a protein similar in size and isoelectric point to BDNF, is released from the multilayers on the agarose and is biologically active during the earlier time points, with decreasing activity at later time points. This is the first demonstration of month-long sustained protein release from an agarose hydrogel, whereby the drug/protein is loaded separately from the agarose hydrogel fabrication process. [source] On the Synthesis of Carbon Nanofibers and Nanotubes by Microwave Irradiation: Parameters, Catalysts, and SubstratesADVANCED FUNCTIONAL MATERIALS, Issue 17 2009Tamara Druzhinina Abstract The microwave (MW)-assisted synthesis of one dimensional carbon systems is introduced as a promising approach to improve the speed and cost-effectiveness of the fabrication process. Improved reaction conditions are generated by direct MW heating and synthesis under advanced reaction conditions. The influence of the reaction conditions is investigated and the importance of individual process parameters on the synthesis is discussed. Temperature and pressure data recorded during the irradiation process are analyzed in detail and allow the determination of essential process parameters. This leads to improved reaction conditions, better control of the one-dimensional carbon nanosystems by tuning the catalyst materials, and allows expanding this approach to initiate the synthesis on a variety of different substrates, such as quartz glass and mica. [source] Fabrication of a Memory Chip by a Complete Self-Assembly Process Using State-of-the-Art Multilevel Cell (MLC) Technology,ADVANCED FUNCTIONAL MATERIALS, Issue 8 2008Anirban Bandyopadhyay Abstract Using a two bit molecular switch, an ultra-dense memory chip has been built following a fully automated fabrication process. Well-ordered templates are grown naturally using a well-defined protocol of temperature variation. This template is so designed that molecules are adsorbed selectively only into particular sites whenever they are bombarded on the template through an e-beam evaporator for a particular time. The technique is a generalized protocol that has been used to grow atomic-scale templates by proper tuning of basic global parameters like temperature and evaporation time. Tuning of the basic template parameters is also demonstrated here, and has been used to scale down parameter values following the same route. Tuning the junction profile should allow selective adsorption of more complicated multi-level switches in future. Therefore, a fairly simple technology has been established that addresses one of the most fundamental issues of continuous miniaturization, i.e., simultaneous automated growth of thousands of atomically precise single molecular devices. [source] A Microfluidic Approach for the Formation of Conductive Nanowires and Hollow Hybrid StructuresADVANCED MATERIALS, Issue 20 2010Josep Puigmartí-Luis A facile fabrication process for micro- and nanometer-scale hybrid structures employing a microfluidic reactor is described. The unique properties of hydrodynamic flow focusing are exploited to promote the formation of well-defined structures with dissimilar morphology and structure in a fast and simple way. The hybrid nanowires are potential candidates for nanometer-sized sensors due to their electrical conductivity and their ease of functionalization. [source] Low cross talk design and simple fabrication process of electrostatic vertical comb-drive actuators for positioning applicationIEEJ TRANSACTIONS ON ELECTRICAL AND ELECTRONIC ENGINEERING, Issue 3 2007Michael Zickar Non-member No abstract is available for this article. [source] Development of a 95/5 poly(L -lactide- co -glycolide)/hydroxylapatite and ,-tricalcium phosphate scaffold as bone replacement material via selective laser sinteringJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2008Rebecca Louise Simpson Abstract 95/5 Poly(L -lactide- co -glycolide) was investigated for the role of a porous scaffold, using the selective laser sintering (SLS) fabrication process, with powder sizes of 50,125 and 125,250 ,m. SLS parameters of laser power, laser scan speed, and part bed temperature were altered and the degree of sintering was assessed by scanning electron microscope. Composites of the 125,250 ,-tricalcium phosphate (CAMCERAM® II) were sintered, and SLS settings using 40 wt % CAMCERAM® II were optimized for further tests. Polymer thermal degradation during processing led to a reduction in number and weight averaged molecular weight of 9% and 12%, respectively. Compression tests using the optimized composite sintering parameters gave a Young's modulus, yield strength, and strain at 1% strain offset of 0.13 ± 0.03 GPa, 12.06 ± 2.53 MPa, and 11.39 ± 2.60%, respectively. Porosity was found to be 46.5 ± 1.39%. CT data was used to create an SLS model of a human fourth middle phalanx and a block with designed porosity was fabricated to illustrate the process capabilities. The results have shown that this composite and fabrication method has potential in the fabrication of porous scaffolds for bone tissue engineering. © 2007 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008 [source] A time-dependent multiphysics, multiphase modeling framework for carbon nanotube synthesis using chemical vapor depositionAICHE JOURNAL, Issue 12 2009Mahmoud Reza Hosseini Abstract A time-dependent multiphysics, multiphase model is proposed and fully developed here to describe carbon nanotubes (CNTs) fabrication using chemical vapor deposition (CVD). The fully integrated model accounts for chemical reaction as well as fluid, heat, and mass transport phenomena. The feed components for the CVD process are methane (CH4), as the primary carbon source, and hydrogen (H2). Numerous simulations are performed for a wide range of fabrication temperatures (973.15,1273.15 K) as well as different CH4 (500,1000 sccm) and H2 (250,750 sccm) flow rates. The effect of temperature, total flow rate, and feed mixture ratio on CNTs growth rate as well as the effect of amorphous carbon formation on the final product are calculated and compared with experimental results. The outcomes from this study provide a fundamental understanding and basis for the design of an efficient CNT fabrication process that is capable of producing a high yield of CNTs, with a minimum amount of amorphous carbon. © 2009 American Institute of Chemical Engineers AIChE J, 2009 [source] Formation process of three-dimensional arrays from silica spheresAICHE JOURNAL, Issue 5 2003Keiji Ishikawa Elucidating the formation process of 3-D arrays from submicrometer-sized particles is a key to creating an optimal fabrication process of photonic crystals. In this research, the spontaneous sedimentation of silica spheres is imaged by in situ confocal laser scanning microscopy, and the dynamics is studied. When the pH is 7.0 and 10, the rate of the formation process of a hexagonal structure is attributed to the transport of spheres in the early stage of precipitation, and can be reproduced by a simple equation for Langmuir-type adsorption, ignoring the desorption part. In a later stage, however, the rate becomes smaller. In the first layer, even after drying, the nearest two spheres are separated, while maintaining a hexagonal structure. From the results, the formation process of three-dimensional arrays from silica spheres is illustrated. [source] Photopolymerization with microscale resolution: Influence of the physico-chemical and photonic parametersJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 11 2008Olivier Soppera Abstract This article is aimed at demonstrating that physicochemical parameters can be used to control the spatial extent (length, width, and shape) of polymer objects in view of micro- and nano-fabrication applications. In particular, we showed that oxygen quenching and internal filter effects could be turned to advantage to modulate the response of the material by controlling the threshold energy of polymerization and/or the shape of the light into the photopolymerizable medium. The experimental configuration used in this study is based on light-induced polymerization at the extremity of an optical fiber that produces polymer micro-objects after development. Spectroscopic approaches and polymerization threshold measurements were performed to quantitatively evaluate the influence of the physicochemical parameters on the micropatterning of photopolymerizable material. Interestingly, fluorescence that is usually regarded as a process competing with photopolymerization reaction, was used for controlling the fabrication process. By this means, it was possible to better understand the impact of a nonhomogeneous irradiation on photopolymerization process and thus, to tune the shape and the size of the final polymer objects. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3783,3794, 2008 [source] Microtensile Bond Strength and Impact Energy of Fracture of CAD-Veneered Zirconia RestorationsJOURNAL OF PROSTHODONTICS, Issue 3 2009Moustafa N. Aboushelib DDS Abstract Purpose: With state-of-the-art CAD/CAM technology, the fabrication of large and complex zirconia frameworks is just a click away. On the other hand, veneering of the frameworks is still operator-dependent. The aim of this work was to evaluate CAD veneering of zirconia restorations in terms of zirconia veneer bond strength and impact energy of fracture in a step towards complete automation of the fabrication process. Materials and Methods: A new CAD/CAM system was used to fabricate a resin replica of the esthetic ceramic required to veneer a zirconia framework. The replica was seated on the zirconia framework and further processed using press-on technology. The bond strength between zirconia and the CAD veneer was evaluated using microtensile bond strength test. The impact energy of fracture of the specimens was also investigated. Manually layered zirconia specimens served as a control (,= 0.05). Results: There was no significant difference in the microtensile bond strength between zirconia and either of the used veneers (39 MPa). Even though the impact energy of fracture of the CAD-veneered and manually layered specimens was almost identical (0.13 J), the former demonstrated a cohesive fracture of the veneer, while the latter failed by delamination of the veneer ceramic. Conclusion: CAD veneering is a reliable method for veneering zirconia restorations. [source] Ion-Exchange Loading of Yttrium Acetate as a Sintering Aid on Aluminum Nitride Powder via Aqueous ProcessingJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 11 2000Yasuhiro Shimizu A novel fabrication process of AlN ceramics via aqueous colloidal processing and pressureless sintering has been presented. The chemical stability of AlN powder in water was improved by the surface chemical modification with sebacic acid, while maintaining a hydrophilic surface. The treatment of the sebacic acid-modified powder with yttrium acetate tetrahydrate resulted in strong immobilization of Y3+ ions, as a sintering aid, at a highly dispersive level on the AlN powder surface through ion exchange with the free carboxyl groups of the sebacic acid molecules attached to the AlN surface. By selecting slip compositions for a well-deflocculated condition and firing conditions to burn out organic components in the slip cast compacts, a thermal conductivity of about 250 W/(m·K) could be attained by the pressureless sintering at 1900°C for 5 h. [source] Improvement of Mechanical Properties of Self Setting Calcium Phosphate Bone Cements Mixed With Different Metal OxidesMATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, Issue 12 2003U. Gbureck Calciumphosphat Zemente; Metalloxide; Mechanische Eigenschaften Abstract Calcium phosphate cements (CPC), based on multicomponent powder mixtures of calcium orthophosphates with medium particle sizes in the region of 1 - 20 ,m, set isothermally in an aqueous environment to form hydroxyapatite (HA). HA cement reactants include tetracalcium phosphate (TTCP), tricalcium phosphate (TCP), dicalcium phosphate anhydrate (DCPA), dicalcium phosphate dihydrate (DCPD), monocalcium phosphate (MCPA) or octacalcium phosphate (OCP). The aim of this study was to improve the mechanical performance of TTCP / DCPA cement by adding several metal oxides to tetracalcium phosphate during the fabrication process. Cements based on tetracalcium phosphate mixed with silica or titanium oxide showed significant increases in compressive strength, approximately 80 - 100 MPa, whilst no change in the mechanical behavior of CPC was observed if zirconia was added. X-ray diffraction measurement confirmed the setting reaction of doped cements was similar to that of pure CPC. Low crystalline HA was found to be the main constituant of set cement; additional phases, such as calcium titanate or calcium zirconate, were not involved in the reaction. A mechanical reinforcement effect was thought to result from changes in the thermodynamic or kinetic solubilities of doped tetracalcium phosphates, this would lead to slower HA crystal formation and a more cross-linked cement structure. Verbesserung der mechanischen Eigenschaften von Calciumphosphat-Zementen durch Modifikation mit verschiedenen Metalloxiden Calciumphosphat-Zemente, CPC, bestehen aus Pulvermischungen verschiedener Calcium orthophophate, beispielsweise Tetracalciumphosphat (TTCP), Tricalciumphosphat (TCP), Dicalciumphosphatanhydrid (DCPA), Dicalciumphosphatdihydrat (DCPD), Monocalcium phosphatanhydrid (MCPA) oder Octacalciumphosphat (OCP) mit durchschnittlichen Partikelgrößen im Bereich von 1 , 20 ,m. Die Zemente binden in wässriger Umgebung isotherm zu Hydroxylapatit ab. Das Ziel dieser Arbeit war die Verbesserung materialspezifischer Eigenschaften , wie die mechanische Festigkeit - eines TTCP / DCPA-Zementes durch die Verwendung von Metalloxiden im Syntheseprozess von Tetracalciumphosphat. Zemente, die aus mit Silicium- oder Titandioxid versetzten Tetracalciumphosphaten hergestellt wurden, zeigten eine deutliche Steigerung der Druckfestigkeit auf Werte von 80 , 100 MPa, während im Falle von Zirkoniumdioxid keine Änderung der mechanischen Stabilität erreicht werden konnte. Röntgendiffraktometrische Untersuchungen ergaben, dass die Abbindereaktion dieser Zemente ähnlich der eines reinen TTCP / DCPA-Zements verläuft. Jeweiliges Hauptprodukt war niedrigkristalliner Hydroxylapatit, die im Herstellungsprozess von Tetracalciumphosphat entstandenen Nebenprodukte Calciumtitanat bzw. ,zirkonat waren nicht an der Abbindereaktion beteiligt. Ein Grund für die Steigerung der mechanischen Stabilität ist offensichtlich die Veränderung der kinetischen und thermodynamischen Löslichkeit der synthetisierten Tetracalciumphosphate, die zu einer langsameren Abbindereaktion und somit einer besseren Vernetzung in der Hydroxylapatitstruktur führt. [source] Synthesis and stability of iron nanoparticles for lunar environment studiesMETEORITICS & PLANETARY SCIENCE, Issue 6 2010Ching-Cheh HUNG However, unlike the true lunar dust, today's simulants do not contain nanophase iron. Two different processes have been developed to fabricate nanophase iron to be used as part of a lunar dust simulant. (1) The first is to sequentially treat a mixture of ferric chloride, fluorinated carbon, and soda lime glass beads at about 300 °C in nitrogen, at room temperature in air, and then at 1050 °C in nitrogen. The product includes glass beads that are gray in color, can be attracted by a magnet, and contains ,-iron nanoparticles (which seem to slowly lose their lattice structure in ambient air during a period of 12 months). This product may have some similarity to the lunar glassy agglutinate, which contains FeO. (2) The second is to heat a mixture of carbon black and a lunar simulant (a mixed metal oxide that includes iron oxide) at 1050 °C in nitrogen. This process simulates lunar dust reactions with the carbon in a micrometeorite at the time of impact. The product contains a chemically modified simulant that can be attracted by a magnet and has a surface layer whose iron concentration increased during the reaction. The iron was found to be ,-iron and Fe3O4 nanoparticles, which appear to grow after the fabrication process. This growth became undetectable after 6 months of ambient air storage, but may last for several years or longer. [source] A flexible RF transmitter module based on flexible printed circuit board by using micro-machining fabrication processMICROWAVE AND OPTICAL TECHNOLOGY LETTERS, Issue 12 2010Seong-Sik Myoung Abstract This article presents a flexible RF transmitter module based on flexible printed circuit board (FPCB). The polyimide with micro-machining fabrication technique is employed for realization of FPCB to achieve the high flexibility as well as low loss at microwave frequency band. The active devices in the proposed flexible RF transmitter are design with InGaP/GaAs hetero-junction bipolar transistor monolithic microwave integrated circuit process, and the passive devices such as the filter and interconnection lines are fully integrated on the FPCB board to avoid use of external off-chip components for maximized flexibility. The FPCB transmitter module is designed for a short-distance sensor network based on OFDM communication system, and the measured conversion gain and error vector magnitude of the fabricated flexible transmitter are 27 dB and ,32 dB, respectively. © 2010 Wiley Periodicals, Inc. Microwave Opt Technol Lett 52:2636,2639, 2010; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.25572 [source] Waveguide bandpass filters for MMIC applicationsMICROWAVE AND OPTICAL TECHNOLOGY LETTERS, Issue 5 2005L. Lalehparvar Abstract Novel 3D multilayer waveguide structures for MMIC filter applications are proposed and examined in this paper. Periodic multilayer-waveguide resonant structures, which can be used for bandpass filters, are presented. The structure has a high Q and supports a simple fabrication process. An MMIC filter based on this proposed periodic-resonator configuration is designed at 74 GHz using the commercial software package HFSS. The simulated S -parameter responses and a photomicrograph of the fabricated monolithic dielectric filled rectangular waveguide on GaAs substrate are presented. © 2005 Wiley Periodicals, Inc. Microwave Opt Technol Lett 46: 471,473, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.21020 [source] Application of microsize light-emitting diode structure for monolithic optoelectronic integrated circuitsPHYSICA STATUS SOLIDI (A) APPLICATIONS AND MATERIALS SCIENCE, Issue 6 2007S. Y. Moon Abstract A Si/III,V,N alloys/Si structure was grown on a Si substrate by solid-source molecular beam epitaxy (SSMBE) with an rf plasma nitrogen source and electron-beam (EB) evaporator. A two-dimensional (2D) growth mode was maintained during the growth of all layers. High-resolution X-ray diffraction (HRXRD) revealed that the structure had a small lattice mismatch to the Si substrate. InGaPN/GaPN double-heterostructure (DH) light-emitting diodes (LEDs) were fabricated on Si/III,V,N alloys/Si structure. The various sized LEDs were fabricated to put into the MOSFET for monolithic optoelectronic integrated circuits (OEIC). The luminescence properties of LEDs were evaluated by electroluminescence (EL). A double emission peak from all LED samples was observed at about 642 nm and 695 nm at room temperature (RT). As injection current increased, the emission peak wavelength changed from the peak wavelength of the InGaPN layer to that of the GaPN layer, likely due to carrier overflow of the active layer. A simplified fabrication process for the microsize LED of the unit circuit was proposed. The LEDs with emission areas from 5 × 5 ,m2 to 20 × 20 ,m2 were fabricated. The LED with an emission area of 5 × 5 ,m2 can be applied to an optical device of a monolithic OEIC. (© 2007 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] High-voltage rf operation of AlGaN/GaN heterojunction FETsPHYSICA STATUS SOLIDI (A) APPLICATIONS AND MATERIALS SCIENCE, Issue 1 2003M. Kuzuhara Abstract This paper reviews the present status of AlGaN/GaN heterojunction FETs for microwave and millimetre-wave applications. The epitaxial structure of the FET and its fabrication process are described. The dc and rf characteristics are also reported, including state-of-the-art power performance at 2 GHz and 30 GHz. The future prospects of GaN-based transistors are also discussed. (© 2003 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Plasmas for texturing, cleaning, and deposition: towards a one pump down process for heterojunction solar cellsPHYSICA STATUS SOLIDI (C) - CURRENT TOPICS IN SOLID STATE PHYSICS, Issue 3-4 2010Mario Moreno Abstract Low temperature plasma deposition of a-Si:H thin films has emerged as a promising alternative for high efficiency hetero junction (HJ) solar cells. In this work we study plasma processes for texturing and cleaning c-Si wafers pursuing a low cost dry fabrication process of HJ solar cells. We have studied two independent plasma processes: i) Texturing of c-Si wafers using SF6 - O2 plasmas in a RIE system, in order to reduce the surface reflectance and therefore improve the light trapping. The effects of the RF power and gas ratio on the c-Si surface texture have been studied in detail. Highly textured surfaces, with very low reflectance values (around 6% in the range of 300 , 1000 nm) have been achieved. ii) Etching of the native oxide and passivation of the c-Si surface by plasma, in a standard RF PECVD system. We used SiF4 plasma with optimized conditions for an efficient native oxide removal, and without breaking the vacuum, 40 nm of a-Si:H were deposited in order to passivate the c-Si surface. High effective lifetime values were obtained (,eff , 1.5 ms), providing high implicit open circuit voltages (Voc , 0.713 V) and low surface recombination velocities (Seff < 9 cm s -1). (© 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] Photonic circuits writing with UV pulsed laserPHYSICA STATUS SOLIDI (C) - CURRENT TOPICS IN SOLID STATE PHYSICS, Issue 1 2007K. R. Kribich Abstract Photonics technology is employed in a growing number of applications. Biological and chemical sensors (E. Udd, Fiber Optic Sensors: An Introduction for Engineers and Scientists, Wiley, New York, 1991 [1]) for health and environment demand an adaptable technology. Network development towards the end-user requires more interconnecting components. Vision, lighting, data processing in hostile environment (spatial, military) need specific technologies. A flexible and low-cost process using good quality material is necessary. The sol-gel process is a chemical method to fabricate glasses at ambient pressure and moderate temperature. Hybrid materials (H.K. Schmidt et al., Proc. SPIE 3136, 220 (1997) [2]), mixing organic and inorganic parts, offer the advantages of polymer-like materials and glasses. We report on a new hybrid sol-gel technology to overcome the drawbacks of the formerly presented one (H. Krug, F. Teillantes, P.W. Oliviers, and H. Schmidt, Proc. SPIE 1758, 448 (1992) [3]). We present the material synthesis, an accurate and flexible fabrication process based on a pulsed UV laser lithography system and the characterisation of the optical waveguides and photonic circuits realised. (© 2007 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] GaN-based Schottky diodes for hydrogen sensing in transformer oilPHYSICA STATUS SOLIDI (C) - CURRENT TOPICS IN SOLID STATE PHYSICS, Issue 6 2006Peter Sandvik Abstract We report the demonstration of robust, GaN-based hydrogen sensors for use directly in transformer oil. These 1 mm2 Schottky diodes were immersed in a closed loop with Voltesso insulating oil for 21 months of continuous testing. They showed good reproducibility in response to hydrogen gases, while exposed to varying temperatures. We will briefly discuss the transformer monitoring application, the device design and fabrication process, and the sensor performance from 21-months of testing. Transfer functions from oil temperature and dissolved gas concentration have been quantified, and those will be briefly discussed. These new sensors offer a novel alternative to electrochemical cell-based sensors for various applications. (© 2006 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [source] | ||||||||||||||||||||||||||||||||||