Home About us Contact
|
Home About us Contact | ||
|
|
||
Exposure Temperatures (exposure + temperature)
Selected AbstractsReproductive responses to photoperiod and temperature by artificially hibernated bumblebee (Bombus terrestris) queensENTOMOLOGICAL RESEARCH, Issue 4 2008Md. Ruhul AMIN Abstract Post-hibernated bumblebee (Bombus terrestris) queens were kept for 1 week under photoperiodic conditions of 8 h light : 16 h dark, and at four different temperatures (24, 28, 32 and 36°C). The reproductive performance of the queens was then observed. It was found that exposure temperature and hibernation duration did not affect the oviposition rate. The pre-oviposition period was found to be shortest (3.8 ± 0.7 days) for queens that had hibernated for 4.0 months and had been activated at 28°C. Timing of the initiation of the switch-point was not affected by exposure temperature and hibernation duration. Significantly higher numbers of workers (268.0 ± 31.4) and sexual queens (119.3 ± 16.8) were produced by the queens that had hibernated for 3.0 months and had been activated at 28 and 36°C, respectively. The queens that had hibernated for 4.0 months and had been activated at 36°C produced the highest number of males (296.2 ± 32.3). [source] Thermal aging of a blend of high-performance fibersJOURNAL OF APPLIED POLYMER SCIENCE, Issue 5 2010Carlos Arrieta Abstract The focus of this work is the study of the thermal aging of high-performance fibers used in the making of fire protective garments. Accelerated thermal aging tests were carried out on fabric samples made up of a blend of Kevlar® (poly p -phenylene terephthalamide) and PBI (poly benzimidazole) staple fibers, as well as on yarns pulled from this fabric, by means of exposure to elevated temperatures, comprised between 190°C and 320°C. All samples underwent loss of breaking force retention. The material thermal life, defined as the time required for the fibers to attain a 50% reduction of the original breaking force, ranged between a dozen of days at the lowest exposure temperature, to less than an hour at the highest. Breaking force data were fitted using the Arrhenius model following two different approaches, namely the extrapolated thermal life value and the shift factors yielded by the time-temperature superposition (TTS). The Arrhenius model seemed to describe appropriately the overall aging process, as inferred from the excellent fit obtained when using both approaches, although activation energies provided from both approaches are different. To follow the chemical evolution of the material with thermal aging, Fourier-transform infrared (FTIR) analyses were conducted. The qualitative analysis of the FTIR spectra showed little evidence of chemical changes between the aged and the nonaged samples, indicating either that the aging process carries on without significant modification of the chemical structure of the fibers, or that FTIR is not an appropriate method to spot such a modification. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Prudent practices for the design and installation of heat-producing devices near wood materialsFIRE AND MATERIALS, Issue 2 2007Vytenis Babrauskas Abstract The conditions required to cause ignition of solid wood materials under short-term heating are examined, and it is found that the appropriate ignition temperature applicable under these conditions is 250°C. It is then shown that ignition requirements are different if long-term heating is involved and that ignition can occur at exposure temperatures much lower than the ignition temperature pertinent to short-term heating. It is shown that hot surfaces of 77 °C or higher, if located for a long duration next to a wood member are liable to lead to its ignition in a self-heating mode. Recommendation is made that prudent practices for design or installation must also involve a suitable safety factor. Copyright © 2006 John Wiley & Sons, Ltd. [source] Nisin Diffusion in Protein Films: Effects of Film Type and TemperatureJOURNAL OF FOOD SCIENCE, Issue 8 2002A. Teerakarn ABSTRACT: Protein films [cast corn zein (CCZ), heat-pressed corn zein (HPCZ), cast wheat gluten (CWG), and heat-pressed wheat gluten (HPWG)] were studied at different exposure temperatures (5, 25, 35, and 45 °C) to determine nisin diffusion in aqueous model systems. Kinetics of nisin diffusion in protein films followed a Fickian diffusion model. The CCZ had the lowest nisin diffusivity and highest nisin retention. Diffusivities in HPCZ, CWG, and HPWG films were not significantly different. Temperature dependence of nisin diffusion in all films followed an Arrhenius model, which indicated no morphological changes within 5 to 45 °C. The activation energy for nisin diffusion in corn-zein films was higher than that in wheat-gluten films. [source] Cell Separator Operation within Temperature Ranges To Minimize Effects on Chinese Hamster Ovary Cell Perfusion CultureBIOTECHNOLOGY PROGRESS, Issue 6 2007Hans Drouin A cell retention device that provides reliable high-separation efficiency with minimal negative effects on the cell culture is essential for robust perfusion culture processes. External separation devices generally expose cells to periodic variations in temperature, most commonly temperatures below 37 °C, while the cells are outside the bioreactor. To examine this phenomenon, aliquots of ,5% of a CHO cell culture were exposed to 60 s cyclic variations of temperature simulating an acoustic separator environment. It was found that, for average exposure temperatures between 31.5 and 38.5 °C, there were no significant impacts on the rates of growth, glucose consumption, or t-PA production, defining an acceptable range of operating temperatures. These results were subsequently confirmed in perfusion culture experiments for average exposure temperatures between 31.6 and 38.1 °C. A 25,1 central composite factorial design experiment was then performed to systematically evaluate the effects of different operating variables on the inlet and outlet temperatures of a 10L acoustic separator. The power input, ambient temperature, as well as the perfusion and recycle flow rates significantly influenced the temperature, while the cell concentration did not. An empirical model was developed that predicted the temperature changes between the inlet and the outlet of the acoustic separator within ±0.5 °C. A series of perfusion experiments determined the ranges of the significant operational settings that maintained the acoustic separator inlet and outlet temperatures within the acceptable range. For example, these objectives were always met by using the manufacturer-recommended operational settings as long as the recirculation flow rate was maintained above 15 L day,1 and the ambient temperature was near 22 °C. [source] | ||||||||||