Home About us Contact
|
Home About us Contact | ||
|
|
||
Environmental Water Samples (environmental + water_sample)
Selected AbstractsCalixarene/Nafion-Modified Bismuth-Film Electrodes for Adsorptive Stripping Voltammetric Determination of LeadELECTROANALYSIS, Issue 17-18 2009Ferenc Torma Abstract This paper presents an enhanced adsorptive stripping voltammetric procedure (AdSV) for the determination of Pb2+, which relies on the accumulation of the metals at a calixarene-based chemically modified bismuth-film electrode on glassy carbon substrate. Following the accumulation of the target metals at open circuit and a medium exchange, both the square wave anodic stripping detection of the metal ions and the in situ bismuth-film formation was performed simultaneously in a Bi3+ containing supporting electrolyte. The analysis of Pb2+ under optimized conditions resulted in stripping responses with good linearity (in the range 0.05,0.6,,M) and precision (RSD=1.12% at 0.2,,M Pb2+; n=10) and low detection limit (0.02,,g/L at 10,min preconcentration). The determination of Pb2+ (0.4,,M) at 100-fold excess of interfering ions (Cd2+, Cu2+ and Zn2+) yielded well resolved lead signal. The analytical utility of the method elaborated was tested in the analysis of trace Pb2+ in environmental water samples. [source] Simultaneous determination of low-molecular-weight organic acids and chlorinated acid herbicides in environmental water by a portable CE system with contactless conductivity detectionELECTROPHORESIS, Issue 10 2007Yan Xu Abstract This report describes a method to simultaneously determine 11 low-molecular-weight (LMW) organic acids and 16 chlorinated acid herbicides within a single run by a portable CE system with contactless conductivity detection (CCD) in a poly(vinyl alcohol) (PVA)-coated capillary. Under the optimized condition, the LODs of CE-CCD ranged from 0.056 to 0.270,ppm, which were better than for indirect UV (IUV) detection of the 11 LMW organic acids or UV detection of the 16 chlorinated acid herbicides. Combined with an on-line field-amplified sample stacking (FASS) procedure, sensitivity enhancement of 632- to 1078-fold was achieved, with satisfactory reproducibility (RSDs of migration times less than 2.2%, and RSDs of peak areas less than 5.1%). The FASS-CE-CCD method was successfully applied to determine the two groups of acidic pollutants in two kinds of environmental water samples. The portable CE-CCD system shows advantages such as simplicity, cost effectiveness, and miniaturization. Therefore, the method presented in this report has great potential for onsite analysis of various pollutants at the trace level. [source] Detection of toxigenic Vibrio cholerae from environmental water samples by an enrichment broth cultivation,pit-stop semi-nested PCR procedureJOURNAL OF APPLIED MICROBIOLOGY, Issue 3 2000J. Theron A pit-stop semi-nested PCR assay for the detection of toxigenic Vibrio cholerae in environmental water samples was developed and its performance evaluated. The PCR technique amplifies sequences within the cholera toxin operon specific for toxigenic V. cholerae. The PCR procedure coupled with an enrichment culture detected as few as four V. cholerae organisms in pure culture. Treated sewage, surface, ground and drinking water samples were seeded with V. cholerae and following enrichment, a detection limit of as few as 1 V. cholerae cfu ml,1 was obtained with amplification reactions from crude bacterial lysates. The proposed method, which includes a combination of enrichment, rapid sample preparation and a pit-stop semi-nested PCR, could be applicable in the rapid detection of toxigenic V. cholerae in environmental water samples. [source] Detection of cryptosporidia and Cryptosporidium parvum oocysts in environmental water samples by immunomagnetic separation,polymerase chain reactionJOURNAL OF APPLIED MICROBIOLOGY, Issue 1 2000S. Hallier-Soulier Cryptosporidium parvum has emerged as one of the most important new contaminants found in drinking water. Current protocols for the detection of cryptosporidia are time-consuming and rather inefficient. We recently described an immunomagnetic separation,polymerase chain reaction (IMS,PCR) assay permitting highly sensitive detection of C. parvum oocysts in drinking water samples. In this study, a second IMS,PCR assay to detect all cryptosporidial oocysts was developed, and both IMS,PCR assays were optimized on river water samples. A comparative study of the two IMS,PCR assays and the classical detection method based on an immunofluorescence assay (IFA) was carried out on 50 environmental samples. Whatever the type of water sample, the discrepancy in C. parvum detection between the IFA and IMS,PCR took the form of IFA-negative/IMS,PCR-positive results, and was caused mainly by the greater sensitivity of IMS,PCR as compared with IFA. Of the 50 water samples, only five tested positive for C. parvum using IMS,PCR, and could constitute a threat to human health. These results show that both IMS,PCR assays provide a rapid (1 d) and sensitive means of screening environmental water samples for the presence of cryptosporidia and C. parvum oocysts. [source] RAPHIDOPHYCEAE [CHADEFAUD EX SILVA] SYSTEMATICS AND RAPID IDENTIFICATION: SEQUENCE ANALYSES AND REAL-TIME PCR ASSAYS,JOURNAL OF PHYCOLOGY, Issue 6 2006Holly A. Bowers Species within the class Raphidophyceae were associated with fish kill events in Japanese, European, Canadian, and U.S. coastal waters. Fish mortality was attributable to gill damage with exposure to reactive oxygen species (peroxide, superoxide, and hydroxide radicals), neurotoxins, physical clogging, and hemolytic substances. Morphological identification of these organisms in environmental water samples is difficult, particularly when fixatives are used. Because of this difficulty and the continued global emergence of these species in coastal estuarine waters, we initiated the development and validation of a suite of real-time polymerase chain reaction (PCR) assays. Sequencing was used to generate complete data sets for nuclear encoded small-subunit ribosomal RNA (SSU rRNA; 18S); internal transcribed spacers 1 and 2, 5.8S; and plastid encoded SSU rRNA (16S) for confirmed raphidophyte cultures from various geographic locations. Sequences for several Chattonella species (C. antiqua, C. marina, C. ovata, C. subsalsa, and C. verruculosa), Heterosigma akashiwo, and Fibrocapsa japonica were generated and used to design rapid and specific PCR assays for several species including C. verruculosa Hara et Chihara, C. subsalsa Biecheler, the complex comprised of C. marina Hara et Chihara, C. antiqua Ono and C. ovata, H. akashiwo Ono, and F. japonica Toriumi et Takano using appropriate loci. With this comprehensive data set, we were also able to perform phylogenetic analyses to determine the relationship between these species. [source] Determination of trace organophosphorus pesticides in water samples with TiO2 nanotubes cartridge prior to GC-flame photometric detectionJOURNAL OF SEPARATION SCIENCE, JSS, Issue 14 2010Yunrui Huang Abstract This article described a new method for the sensitive determination of organophosphorus pesticides in water samples using SPE in combination with GC-flame photometric detection. In the procedure of method development, TiO2 nanotubes were used as SPE adsorbents for the enrichment of organophosphorus pesticides from water samples. Several factors, such as eluent and its volume, sample pH, sample volume, sample flow rate, and concentration of humic acid, were optimized. Under the optimal conditions, the proposed method had good linear ranges as 0.1,40,,g/L for each of them, LOD of 0.11, 0.014, and 0.0025,,g/L, and LOQs of 0.37, 0.047, and 0.0083,,g/L for chlorpyrifos, phorate, and methyl parathion, respectively. The proposed method was validated with real environmental water samples and the spiked recoveries were over the range of 86.5,115.1%. All these results indicated that TiO2 nanotubes, as a new SPE adsorbent, would be used widespread for the preconcentraiton and determination of environmental pollutants in the future. [source] Magnesium oxide microspheres as a novel solid-phase extraction sorbent for the determination of benzo[a]pyrene in environmental water samplesJOURNAL OF SEPARATION SCIENCE, JSS, Issue 12 2010Jing Jin Abstract Magnesium oxide microspheres were developed as a novel SPE sorbent for the determination of benzo[a]pyrene (BaP), one of the most potent carcinogenic agents, in environmental water samples. The parameters controlling the extraction efficiency, such as elution volume, flow rate, pH values, and breakthrough volume, were investigated in detail. Considering the facile preparation and satisfying recovery, a corresponding analytical method has been developed to determine the concentration of BaP in real tap water, river water, and seawater. The recoveries for the spiked BaP were excellent (94,101%). [source] Highly sensitive determination of tetrabromobisphenol A and bisphenol A in environmental water samples by solid-phase extraction and liquid chromatography-tandem mass spectrometryJOURNAL OF SEPARATION SCIENCE, JSS, Issue 11 2010Ru-Song Zhao Abstract Using bamboo-activated charcoal as SPE adsorbent, a novel SPE method was developed for the sensitive determination of tetrabromobisphenol A and bisphenol A in environmental water samples by rapid-resolution LC-ESI-MS/MS. Important parameters influencing extraction efficiency, including type of eluent, eluent volume, sample pH, volume and flow rate, were investigated and optimized. Under the optimal extraction conditions (eluent: 8,mL methanol, pH: 7; flow rate: 4,mL/min; sample volume: 100,mL), low LODs (0.01,0.02,ng/mL), good repeatability (6.2,8.3%) and wide linearity range (0.10,10,ng/mL) were obtained. Satisfied results were achieved when the proposed method was applied to determine the two target compounds in real-world environmental water samples with spiked recoveries over the range of 80.5,119.8%. All these facts indicate that trace determination of tetrabromobisphenol A and bisphenol A in real-world environmental water samples can be realized by bamboo-activated charcoal SPE-rapid resolution-LC-ESI-MS/MS. [source] Sensitive determination of phenols in environmental water samples with SPE packed with bamboo carbon prior to HPLCJOURNAL OF SEPARATION SCIENCE, JSS, Issue 4 2009Ru-Song Zhao Abstract Bamboo carbon, an inexpensive, readily available material, has attracted great attention in recent years because of adsorptive properties. In this paper, the potential of bamboo carbon as a SPE adsorbent for the determination of phenols, was investigated. Phenols are important environmental contaminants that may adversely affect human health. Parameters influencing extraction efficiency, including type of eluent, eluent volume, amount of adsorbent, as well as sample pH, volume, and flow rate were investigated and optimized. The optimized results exhibited excellent linear relationships between peak area and phenol concentrations over the range of 2.0,100 ng/mL, with precision between 2.2,7.2%. The LODs were 0.06,0.4 ng/mL for the eight phenols tested. The proposed method has been successfully applied to the analysis of several real-world environmental water samples. These results indicate that bamboo carbon may be used as a novel SPE adsorbent for the concentration and determination of phenols in real environmental water samples. [source] Determination of nonsteroidal antiinflammatory drugs in water samples using liquid chromatography coupled with diode-array detector and mass spectrometryJOURNAL OF SEPARATION SCIENCE, JSS, Issue 17 2005Jolanta Debska Abstract An analytical method for the determination of trace levels of six different nonsteroidal antiinflammatory drugs (NSAIDs) in water samples has been developed and validated. Environmentally relevant pharmaceuticals were chosen according to human consumption in Poland. Final analysis of the target compounds was performed by RP LC,diode-array detection,MS, whereas sample preparation included an SPE step. For this SPE step, a number of packing materials, such as LiChrolut RP-18, calixarene, Strata-X, BAKERBOND Narc-2, BAKERBOND Polar Plus, BAKERBOND styrene divinylbenzene-1, and Discovery DSC-18, were used, and their respective advantages and disadvantages in this study were discussed. The RP-18 phase was found to be the most retentive for all analytes. The detection limits for compounds in surface waters were varied from 0.005 for diflunisal to 0.095 ,g/L for ibuprofen. The average recoveries of NSAIDs from the surface water samples ranged from 80 up to 103%. RSD value is relatively low (from 4% for fenoprofen up to 8% for ibuprofen). The performance of the method was tested with several environmental water samples. [source] Validation of a quantitative assay using GC/MS for trace determination of free and conjugated estrogens in environmental water samplesJOURNAL OF SEPARATION SCIENCE, JSS, Issue 1-2 2003Asmaa Mouatassim-Souali Abstract It has been shown that sewage effluent can discharge human hormones and pharmaceuticals, particularly estrogens and synthetic chemicals, which are able to disrupt animal and human endocrine systems into surface waters. Since many surface waters receive sewage effluent and are subsequently used to produce drinking water, it is of principal interest to assess their contamination level and thereby their possible public health and environmental impact. To date, no data concerning the occurrence of estrogens present in the French aquatic environment are available. We therefore developed and validated an analytical procedure, which allows simultaneous quantitative determination of three natural estrogens, 17,-estradiol, estriol, and estrone and one of the synthetic estrogens most widely used in contraception, ethinylestradiol, in water. Water samples are extracted using solid-phase extraction (SPE) and then separated by gas-chromatography coupled with mass spectrometric detection. Under our conditions, detection limits of estrogens reached the pg range of injected sample, i. e. less than 0.1 ng L,1. Conjugated estrogens were also investigated using the same procedure as described above but with a enzymatic hydrolysis preliminary step before extraction. The analysis of samples collected from four wastewater treatment plants and from surface water showed significant concentrations of estrogens ranging from 2 to 18 ng L,1 and from 0.5 to 3 ng L,1, respectively. Furthermore, no estrogen conjugated forms were detected in the water samples. [source] Evaluation and applicability of a purification method coupled with nested PCR for the detection of Toxoplasma oocysts in waterLETTERS IN APPLIED MICROBIOLOGY, Issue 5 2006C. Kourenti Abstract Aims:, To describe the development, evaluation and applicability of a complete method for the detection of Toxoplasma gondii in water. Methods and Results:, The method incorporated concentration of water samples by Al2(SO4)3 -flocculation, purification by discontinuous sucrose gradients and detection of toxoplasmic DNA by 18S-rRNA nested PCR. Tap water replicates and natural water samples were seeded with defined numbers of Toxoplasma oocysts and processed for evaluation studies. When applied to environmental samples, the method gave highest detection sensitivities of 100 oocysts in river water and 10 oocysts in well- and sea water. The method was finally applied in 60 water samples of different quality and origin collected over a 14-month period. Toxoplasmic DNA was detected in four samples. Conclusions:, The method offers an alternative towards improving current methods that can be used for the detection of Toxoplasma oocysts in environmental water samples. Significance and Impact of the Study:, The method in its current form will be helpful for assessment of Toxoplasma contamination in water resources, particularly after outbreak events. [source] Quantitative RT-PCR for the enumeration of noroviruses (Norwalk-like viruses) in water and sewageLETTERS IN APPLIED MICROBIOLOGY, Issue 2 2004M.A. Laverick Abstract Aims:, Aims of investigation: (i) develop a quantitative RT-PCR for noroviruses and (ii) evaluate it on environmental samples. Methods and Results:, Noroviruses in environmental water samples were concentrated by adsorption/elution/flocculation. Sewage was processed by clarification and protein flocculation. Norovirus-specific cDNA produced by primer-directed reverse transcription of extracted RNA was amplified by LightCycler® and accumulation of product monitored by observation of fluorescence induced by the incorporation of SYBR Green. Absolute quantitation of product was achieved by construction of standard curves using quantitative standards produced by cloning a modified sequence of the 3,-region of the forward norovirus primer. Reaction specificity was confirmed by analysis of product melting curves. Conclusions:, Sewage was found to contain up to 1·8 × 106 norovirus cDNA copies per 100 ml and effluent contained up to 1·7 × 106 copies per 10 l. Marine bathing water and recreational river waters also contained noroviruses. Sample inhibition was detected to varying degrees in most sample types. Significance and Impact of the Study:, The study will enable quantitative comparisons be made of samples from different locations and treatment processes, and inform the debate on the revision of the EU Bathing Water Directive; it will have important implications for the analysis of samples derived from different aquatic matrices, and from foods. [source] Application of functional group modified substrate in room-temperature phosphorescence, I,, -cyclodextrin modified paper substrate for enrichment and determination of fluorene and acenaphtheneLUMINESCENCE: THE JOURNAL OF BIOLOGICAL AND CHEMICAL LUMINESCENCE, Issue 4-5 2005Ruohua Zhu Abstract A novel method for the determination of fluorene and acenaphthene on solid phase extraction,room-temperature phosphorescence (SPE,RTP) was studied. , -cyclodextrin (, -CD) was chemically bonded onto chromatography paper by reaction with epichorohydrin in an ultrasonic bath. The RTP signal of fluorene and acenaphthene included on the , -CD-modified paper was increased more than 10 times compared with non-modified filter paper, indicating the formation of the inclusion complex. The conditions for the of RTP of compounds were studied in detail. The linear ranges of fluorene and acenaphthene concentrations to the RTP intensity were over two orders of magnitude (8.0 × 10,7,4.0 × 10,5 mol/L for fluorene) with a correlation coefficient of 0.999. The concentration limits of detection for fluorene and acenaphthene were 1.11 × 10,8 mol/L and 3.8 × 10,7 mo/L, respectively. When the sampling volume was 10 µL, the absolute LODs for fluorene and acenaphthene were 18.4 pg/spot and 0.58 ng/spot, respectively. The modified filter paper was used for solid phase extraction (SPE) and the retention behaviour of fluorene and acenaphthene was examined. The enrichment efficiency of the analytes was higher than 100-fold. The SPE,RTP coupling technique was applied directly to the determination of fluorene and acenaphthnene in environmental water samples. Copyright © 2005 John Wiley & Sons, Ltd. [source] Cloud point extraction combined with electrothermal vaporization inductively coupled plasma mass spectrometry for the speciation of inorganic selenium in environmental water samplesRAPID COMMUNICATIONS IN MASS SPECTROMETRY, Issue 19 2006Beibei Chen A new method based on cloud point extraction (CPE) separation and electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICPMS) detection has been proposed for the speciation of inorganic selenium in environmental waters. When the temperature of the system is higher than the cloud point temperature (CPT) of the selected surfactant Triton X-114, the complex of Se(IV) with ammonium pyrrolidine dithiocarbamate (APDC) seems to be extracted into the surfactant-rich phase, whereas the Se(VI) remains in aqueous solutions. Thus, an insitu separation of Se(IV) and Se(VI) could be realized. The concentrated analyte was introduced into the ETV-ICP mass spectrometer for determination of Se((IV) after dilution with 200,µL methanol. Se(VI) was reduced to Se(IV) prior to determining total selenium, and its assay was based on subtracting Se(IV) from total selenium. The main factors affecting the CPE and the vaporization behavior of the analyte were investigated in detail. Under the optimized experimental conditions, the limit of detection (LOD) for Se(IV) was 8.0,ng/L with an enhancement factor of 39 when 10,mL of sample solution was preconcentrated to 0.2,mL. The relative standard deviation (RSD) was found to be 3.9% (CSe(IV),=,1.0,µg/L, n,=,7). The proposed method was applied to the speciation of inorganic selenium in different environmental water samples with the recovery for the spiked samples in the range of 82,102%. Copyright © 2006 John Wiley & Sons, Ltd. [source] Analysis of estrogenic contaminants in river water using liquid chromatography coupled to ion trap based mass spectrometryRAPID COMMUNICATIONS IN MASS SPECTROMETRY, Issue 14 2002Tom Benijts A precise and reliable method, using liquid chromatography combined with ion trap based mass spectrometry, for the determination of three endogenous estrogens, namely, estrone, estradiol, and estriol, and two synthetic estrogens, ethinyl estradiol and diethylstilbestrol, in environmental water samples was developed. Optimization of the parameter settings of the ion source and mass analyzer as well as evaluation of solvent composition were carried out by continuous introduction of standards through a syringe pump. In negative ion mode the electrospray ionization source gave acceptable results. The optimum solvent used consisted of water/acetonitrile, with no volatile bases or buffers added. A simple, off-line, manual solid-phase extraction method was developed for sample preparation of environmental water samples. Recoveries were over 86% for all compounds. The method was validated and found to be linear, selective, and robust. For analysis of a 50-mL sample, the limit of detection (LOD) ranged from 3.2 to 10.6,ng/L for all compounds, and the limit of quantitation (LOQ) from 10.6 to 35.0,ng/L. Within-day (n,=,5) and total (n,=,5) reproducibility were investigated at three different concentration levels and ranged from 6.2 to 9.5% and 9.4 to 12.1%, respectively. Finally, the method was applied to real-world samples. Copyright © 2002 John Wiley & Sons, Ltd. [source] | |||||||||||||