Home About us Contact
|
Home About us Contact | ||
|
|
||
Electrode Layer (electrode + layer)
Selected AbstractsAdhesion and Percolation Parameters in Two Dimensional Pd,LSCM Composites for SOFC Anode Current CollectionADVANCED FUNCTIONAL MATERIALS, Issue 5 2010Samir Boulfrad Abstract This paper is concerned with palladium,(La0.75Sr0.25)0.97Cr0.5Mn0.5O3 (LSCM) composite current collectors for solid oxide fuel cells (SOFCs); the composites, which are in a 2D configuration (thickness of about 8,10,µm), are deposited upon an LSCM electrode layer on top of an yttria zirconia electrolyte substrate. The influence of the LSCM particle size on the adhesion between palladium and LSCM are reported and discussed. Compositions using four different LSCM particle sizes (0.21, 0.49, 0.64, and 0.81,µm) with sintered Pd particle sizes approaching 10,µm are investigated. The best bonding is obtained when smaller particles are used. The electrical dc conductivity of the composite is reported as a function of the palladium volume fraction for all used LSCM particle sizes. The measured experimental values present typical insulating,conductive percolation. However, the transition occurs at ,33% of the conductive phase, that is, a lower percentage than for 2D ideal systems and a higher percentage than for 3D ideal systems. This is consistent with lower-dimension percolation for a system of large-grained conductors and small-grained insulators. The general effective media (GEM) equation is used to fit the experimental data, and the two main parameters (the threshold point ,c and the exponent t) are defined. [source] Position-sensitive radiation detectors made of single crystal CVD diamondPHYSICA STATUS SOLIDI (A) APPLICATIONS AND MATERIALS SCIENCE, Issue 9 2009M. Pomorski Abstract Based on a single crystal chemical vapour deposition (scCVD) diamond plate a position sensitive detector [position sensitive detection position sensitive detector (PSD)] has been fabricated. The ,9,mm2 sensing area of the detector consists of a diamond-like carbon (DLC) thin film, in the form of a plane-pad resistive electrode layer deposited on the scCVD surface. The 1D position information is obtained from the resistive charge division between two collecting electrodes located at the extremities of the DLC sensing electrode. The detector properties have been tested using a 241Am ,-particles source. The timing characteristics of the device were probed using broad-band (BB) electronics: the signal formation does not exceed 30,ns, thus detector operation with a negligible ballistic effect is possible at high rates approaching 107,particles/s. The linearity and position resolution of the device was measured using low-noise charge-sensitive (CS) electronics: the position resolution reaches 30,µm (,), the deviation from linearity remain below 2% in the full range of the detector sensing area. [source] Experimental Study on the Molecular Dimension and Configuration of Polymer and Its Flow Characteristics from Electrolyte EffectCHINESE JOURNAL OF CHEMISTRY, Issue 4 2009Xiangguo LU Abstract Molecular clew dimension and configuration of polymer, and flow characteristics of polymer solution were studied from electrolyte effect, by making use of dynamic light scattering (DLS), scanning electron microscopy (SEM), apparent viscosity method and core flow experiment. It can be observed that with the electrolyte concentration increasing, there exists a variation trend of "decreasing, increasing and decreasing again" to the molecular clew dimension of the polymer. The compression action of Ca2+ or Mg2+ to the double electrode layer of polymer molecules is more powerful by comparison against Na+, which results in that Ca2+ and Mg2+ have a more extensive effect on the viscosity of polymer solution, and clew dimensions and their distribution. With the electrolyte concentration increasing, the polymer molecular configuration of multi-layer stereoscopic random reticulation transformed into a dendritic one. During the succeeding water flooding, the variation degree of injection pressure of core was mainly determined by the swelling extent of molecular clew of retained polymer and the produced amount of polymer. And the bigger the molecular weight of polymer is, the stronger the compression or swelling action of electrolyte to the molecule clews is, and the greater the increasing degree of injection pressure during succeeding water flooding is. The greater difference of electrolyte concentrations in used water between polymer flooding and succeeding water flooding can result in greater increasing degree of injection pressure during the succeeding water flooding. So, an advisable increasing in difference of electrolyte concentrations in used water between the polymer flooding and succeeding water flooding was proposed when designing the polymer flooding performance in oilfields, which has promising result for improving effect of polymer flooding. [source] Effect of Nickel Oxide/Yttria-Stabilized Zirconia Anode Precursor Sintering Temperature on the Properties of Solid Oxide Fuel CellsJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 3 2000Søren Primdahl An NiO/yttria-stabilized zirconia (YSZ) layer sintered at temperatures between 1100° and 1500°C onto dense YSZ electrolyte foils forms the precursor structure for a porous Ni/YSZ cermet anode for solid oxide fuel cells. Conflicting requirements for the electrochemical performance and mechanical strength of such cells are investigated. A minimum polarization resistance of 0.09 ,.cm2at 1000°C in moist hydrogen is obtained for sintering temperatures of 1300°,1400°C. The mechanical strength of the cells decreases with increased sintering temperature because of the formation of channel cracks in the electrode layers, originating in a thermal expansion coefficient mismatch between the layers. [source] Influence of imidazolium-based ionic liquids on the performance of ionic polymer conductor network composite actuatorsPOLYMER INTERNATIONAL, Issue 3 2010Sheng Liu Abstract We investigated the influence of ionic liquids (ILs) on the electromechanical performance of ionic polymer conductor network composite (IPCNC) actuators. Four imidazolium ILs with two cations of different sizes, i.e. 1-ethyl-3-methylimidazolium ([EMI+]) and 1-butyl-3-methylimidazolium ([BMI+]), and two anions of different sizes, i.e. tetrafluoroborate ([BF4,]) and trifluoromethanesulfonate ([Tf,]), were used. The IPCNC actuators were fabricated using a direct assembly method with RuO2/Nafion® nanocomposite as the electrode layers. The experimental results reveal that the actuator strain response time is nearly one order of magnitude shorter than the charging time. The IPCNCs with [EMI+][Tf,] exhibit the highest capacitance and the fastest response in both actuation and electrical charging as capacitors. In contrast, the IPCNCs with [EMI+][BF4,] display the slowest charging time and lowest value of capacitance as capacitors. The IPCNCs with [BMI+][BF4,] show the slowest response time. Furthermore, although the ILs used have a marked effect on the capacitances of the IPCNCs, using different ILs does not cause much change in the maximum strain of these IPCNCs. Consequently, the IPCNC actuators with [EMI+][BF4,] show the highest electromechanical conversion efficiency while those with [EMI+][Tf,] have the lowest electromechanical efficiency because of the highest capacitance and largest input electrical energy. The experimental results indicate that the two oppositely charged ions contribute in opposite manner to the strain response and hence the observed shorter actuation response time is likely caused by the strain cancellation effect between the cations and anions. Copyright © 2010 Society of Chemical Industry [source] | ||||||||||