Home  About us  Contact
 

Element Procedure (element + procedure)

Distribution by Scientific Domains
Engineering100%

Kinds of Element Procedure

  • finite element procedure
    		•

    Selected Abstracts

    Adaptive superposition of finite element meshes in non-linear transient solid mechanics problems

    INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING, Issue 9 2007
    Z. Yue
    Abstract An s-adaptive finite element procedure is developed for the transient analysis of 2-D solid mechanics problems with material non-linearity due to progressive damage. The resulting adaptive method simultaneously estimates and controls both the spatial error and temporal error within user-specified tolerances. The spatial error is quantified by the Zienkiewicz,Zhu error estimator and computed via superconvergent patch recovery, while the estimation of temporal error is based on the assumption of a linearly varying third-order time derivatives of the displacement field in conjunction with direct numerical time integration. The distinguishing characteristic of the s-adaptive procedure is the use of finite element mesh superposition (s-refinement) to provide spatial adaptivity. Mesh superposition proves to be particularly advantageous in computationally demanding non-linear transient problems since it is faster, simpler and more efficient than traditional h-refinement schemes. Numerical examples are provided to demonstrate the performance characteristics of the s-adaptive method for quasi-static and transient problems with material non-linearity. Copyright © 2007 John Wiley & Sons, Ltd. [source]

    A plasticity based model and an adaptive algorithm for finite element analysis of reinforced concrete panels

    INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING, Issue 11 2002
    J. Pravida
    Abstract This paper deals with an adaptive finite element procedure for the analysis of plain and reinforced concrete panels in a state of plane stress. Therefore, we will present a plasticity based model for plain concrete which captures the two failure modes of concrete within one formulation. In spite of a simple formulation the model is capable to describe the different mechanisms for tensile failure as well as for compression fracture. To restrict the time discretization error and the spatial discretization error to certain tolerances, the constitutive model is embedded in an adaptive algorithm which controls the size of the incremental load steps and leads to a hierarchical mesh refinement if necessary. The application of the model will be shown by various numerical examples. Copyright © 2002 John Wiley & Sons, Ltd. [source]

    Retracted and replaced: A flow-condition-based interpolation finite element procedure for triangular grids

    INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS, Issue 8 2005
    Haruhiko Kohno
    Abstract A flow-condition-based interpolation finite element scheme is presented for use of triangular grids in the solution of the incompressible Navier,Stokes equations. The method provides spatially isotropic discretizations for low and high Reynolds number flows. Various example solutions are given to illustrate the capabilities of the procedure. This article and been retracted and replaced. See retraction and replacement notice DOI: 10.1002/fld.1247.abs. Copyright © 2005 John Wiley & Sons, Ltd. [source]

    Three-dimensional finite element analysis of lined tunnels

    INTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 3 2001
    C. E. Augarde
    Abstract This paper describes finite element procedures that have been developed to model the ground movements that occur when a shallow tunnel is installed in a clay soil. This study is part of a wider project concerned with the development of new methods to predict the likely extent of damage to surface structures caused by nearby shallow tunnelling. This particular paper, however, is concerned only with the numerical model of tunnel installation. The structural liner is an important component of this tunnel installation model; two different ways of modelling the liner (based on continuum elements and shell elements) are discussed in the paper. A test problem consisting of the installation of a lined tunnel in an elastic continuum is used to investigate the merits of these different approaches. When continuum elements are used to model the liner, the numerical results agree well with an analytical solution to the problem. When shell elements are used to model the liner, however, the results were found to be significantly influenced by the particular formulation adopted for the shell elements. Example analyses, involving incremental tunnel construction in a clay soil where the soil is modelled using a kinematic hardening plasticity model, are described. These analyses confirm that a thin layer of continuum elements may be used, satisfactorily, to model tunnel linings in a soil,structure interaction analysis of this sort. Copyright © 2001 John Wiley & Sons, Ltd. [source]

    Adaptive finite element procedures for elastoplastic problems at finite strains

    PROCEEDINGS IN APPLIED MATHEMATICS & MECHANICS, Issue 1 2003
    A. Koch Dipl.-Ing.
    A major difficulty in the context of adaptive analysis of geometrically nonlinear problems is to provide a robust remeshing procedure that accounts both for the error caused by the spatial discretization and for the error due to the time discretization. For stability problems, such as strain localization and necking, it is essential to provide a step,size control in order to get a robust algorithm for the solution of the boundary value problem. For this purpose we developed an easy to implement step,size control algorithm. In addition we will consider possible a posteriori error indicators for the spatial error distribution of elastoplastic problems at finite strains. This indicator is adopted for a density,function,based adaptive remeshing procedure. Both error indicators are combined for the adaptive analysis in time and space. The performance of the proposed method is documented by means of representative numerical examples. [source]