Home About us Contact
|
Home About us Contact | ||
|
|
||
Critical Strain (critical + strain)
Selected AbstractsModeling of Hot Ductility During Solidification of Steel Grades in Continuous Casting , Part I,ADVANCED ENGINEERING MATERIALS, Issue 3 2010Dieter Senk The present paper gives an overview of the simultaneous research work carried out by RWTH Aachen University and ThyssenKrupp Steel Europe AG. With a combination of sophisticated simulation tools and experimental techniques it is possible to predict the relations between temperature distribution in the mould, solidification velocity, chemical steel composition and, furthermore, the mechanical properties of the steel shell. Simulation results as well as experimentally observed microstructure parameters are used as input data for hot tearing criteria. A critical choice of existing hot tearing criteria based on different approaches, like critical strain and critical strain rate, are applied and developed. The new "damage model" is going to replace a basic approach to determine hot cracking susceptibility in a mechanical FEM strand model for continuous slab casting of ThyssenKrupp Steel Europe AG. Critical strains for hot cracking in continuous casting were investigated by in situ tensile tests for four steel grades with carbon contents in the range of 0.036 and 0.76,wt%. Additionally to modeling, fractography of laboratory and industrial samples was carried out by SEM and EPMA and the results are discussed. [source] Bifurcated Mechanical Behavior of Deformed Periodic Porous SolidsADVANCED FUNCTIONAL MATERIALS, Issue 9 2009Srikanth Singamaneni Abstract The transformation of periodic microporous structures fabricated by interference lithography followed by their freezing below glass transition is described. Periodic porous microstructures subjected to internal compressive stresses can undergo sudden structural transformation at a critical strain. The pattern transformation of collapsed pores is caused by the stresses originated during the polymerization of acrylic acid (rubbery component) inside of cylindrical pores and the subsequent solvent evaporation in the organized microporous structure. By confining the polymerization of acrylic acid to localized porous areas complex microscopic periodic structures can be obtained. The control over the mechanical instabilities in periodic porous solids at a sub-micron scale demonstrated here suggests the potential mechanical tunability of photonic, transport, adhesive, and phononic properties of such periodic porous solids. [source] Sex differences in long bone fatigue using a rat modelJOURNAL OF ORTHOPAEDIC RESEARCH, Issue 10 2006Luisa D. Moreno Abstract Stress fractures can occur because of prolonged exercise and are associated with cyclic loading. Fatigue is the accumulated damage that results from cyclic loading and bone fatigue damage is of special concern for athletes and army recruits. Existing literature shows that the rates of stress fracture for female athletes and female army recruits are higher than their male counterparts. In this study, we used an ex vivo rat model to investigate the fatigue response of female and male bones. We determined the strain versus number of cycles to failure (S/N) for each sex and found that for a certain initial strain (5,000,7,000 µ,) female bones have shorter fatigue life. To further characterize the bone response to fatigue, we also determined the creep that occurred during the fatigue test. From the creep data, for a certain strain range, female bones accumulated greater residual strains and reached the critical strain at a faster rate. In summary, this study demonstrates that female rat bones have a lower resistance to fatigue in the absence of a physiological response such as muscle fatigue or osteogenic adaptation. From these results, we hypothesized that creep was the underlying mechanism that accounted for the fast deterioration of female bones during fatigue. © 2006 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 24:1926,1932, 2006 [source] Stress generation in the tension wood of poplar is based on the lateral swelling power of the G-layerTHE PLANT JOURNAL, Issue 4 2008Luna Goswami Summary The mechanism of active stress generation in tension wood is still not fully understood. To characterize the functional interdependency between the G-layer and the secondary cell wall, nanostructural characterization and mechanical tests were performed on native tension wood tissues of poplar (Populus nigra × Populus deltoids) and on tissues in which the G-layer was removed by an enzymatic treatment. In addition to the well-known axial orientation of the cellulose fibrils in the G-layer, it was shown that the microfibril angle of the S2-layer was very large (about 36°). The removal of the G-layer resulted in an axial extension and a tangential contraction of the tissues. The tensile stress,strain curves of native tension wood slices showed a jagged appearance after yield that could not be seen in the enzyme-treated samples. The behaviour of the native tissue was modelled by assuming that cells deform elastically up to a critical strain at which the G-layer slips, causing a drop in stress. The results suggest that tensile stresses in poplar are generated in the living plant by a lateral swelling of the G-layer which forces the surrounding secondary cell wall to contract in the axial direction. [source] | |||||||||||||