Home  About us  Contact
 

Composite Plates (composite + plate)

Distribution by Scientific Domains
Polymers and Materials Science100%

Selected Abstracts

Experimental study of sharp-tipped projectile perforation of GFRP plates containing sand filler under high velocity impact and quasi-static loadings

POLYMER COMPOSITES, Issue 10 2009
Ali Reza Sabet
Penetration and perforation behavior of glass fiber reinforced plastic (GFRP) plates containing 20% sand filler have been investigated via high velocity impact tests using sharp tipped (30°) projectile and quasi-static perforation tests. Two size sand filler (75 and 600 ,m) were used in 4-, 8-, and 14-layered laminated composite plates to study sensitivity of filler size toward loading system. Composite plates were examined for perforation load rate at 5 mm/min and high-velocity impact loading up to 220 m/s. Results indicated higher energy absorption for GFRP plates containing sand filler for both high-velocity impact and quasi-static perforation tests. Higher ballistic limits were recorded for specimens containing sand filler. The study showed clear role played by coarse-sized sand filler as a secondary reinforcement in terms of higher energy absorption as compared with nonfilled and specimens containing fine-sized fillers. The investigation successfully characterized behavior of quasi-static test during penetration and perforation of the sharp-tipped indenter as an aid for impact application studies. Residual frictional load in the specimens containing sand filler constituted considerable portion of load bearing during perforation in quasi-static tests. Delaminations followed by fiber and matrix fracture were major failure mode in high-velocity tests and the main energy absorbing mechanism in thick-walled plates, whereas in quasi-static tests the failures were more of matrix fracture and fiber sliding. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers [source]

Impact behavior of hybrid composite plates

JOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2010
Metin Sayer
Abstract This experimental study deals with the impact response of hybrid composite laminates. Two different hybrid composite laminates, aramid/glass and aramid/carbon, and two different stacking sequences, such as [0/0/90/90]A+ [90/90/0/0]G for AG1 and [0/90/±45]A+ [±45/90/0]G for AG2 and so on (see Table I), were chosen for impact testing. The impact energy was gradually increased until complete perforation took place, and an energy profiling method (EPM) was used to identify the perforation thresholds of composites. The damaged samples were visually inspected. The images of the several samples subjected to various impact energies were registered and used for comparison and identifying damage mechanisms. The perforation thresholds for [0/90/±45]s aramid/glass and aramid/carbon laminates were found to be approximately 5% higher than those for their counterparts with the [0/0/90/90]s stacking sequence. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source]

Atmospheric Pressure Plasma Treatment of Glass Fibre Composite for Adhesion Improvement

PLASMA PROCESSES AND POLYMERS, Issue S1 2007
Yukihiro Kusano
Abstract Glass-fibre-reinforced polyester composite plates were treated with an atmospheric pressure dielectric barrier discharge. Synthetic air was used as the treatment gas. The water contact angle dropped markedly from 84 to 22° after a 2-s treatment, and decreased to 0° when the composite plates were treated for more than 30 s. X-Ray photoelectron spectroscopic analysis showed that the contents of aluminium and oxygen on the surface increased with the plasma treatment. The adhesion strength of the 2-s treated surface was comparable to or higher than that achieved by conventional mechanical surface roughening. It decreased when the surfaces were treated for 5 and 15 s, but recovered for 30-s treatment. [source]

Contribution of wood fiber hygroexpansion to moisture induced thickness swelling of composite plates

POLYMER COMPOSITES, Issue 5 2010
Karin M. Almgren
One of the main drawbacks of wood fiber-based composite materials is their propensity to swell due to moisture uptake. Because the wood fibers are usually the main contributor to hygroexpansion, it is of interest to quantify the hygroexpansion coefficient of wood fibers, to compare and rank different types of fibers. This investigation outlines an inverse method to estimate the transverse hygroexpansion coefficient of wood fibers based on measurements of moisture induced thickness swelling of composite plates. The model is based on composite micromechanics and laminate theory. Thickness swelling has been measured on polylactide matrix composites with either bleached reference fibers or crosslinked fibers. The crosslinking modification reduced the transverse hygroexpansion of the composites and the transverse coefficient of hygroexpansion of the fibers was reduced from 0.28 strain per relative humidity for reference fibers to 0.12 for cross-linked fibers. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers [source]

Experimental study of sharp-tipped projectile perforation of GFRP plates containing sand filler under high velocity impact and quasi-static loadings

POLYMER COMPOSITES, Issue 10 2009
Ali Reza Sabet
Penetration and perforation behavior of glass fiber reinforced plastic (GFRP) plates containing 20% sand filler have been investigated via high velocity impact tests using sharp tipped (30°) projectile and quasi-static perforation tests. Two size sand filler (75 and 600 ,m) were used in 4-, 8-, and 14-layered laminated composite plates to study sensitivity of filler size toward loading system. Composite plates were examined for perforation load rate at 5 mm/min and high-velocity impact loading up to 220 m/s. Results indicated higher energy absorption for GFRP plates containing sand filler for both high-velocity impact and quasi-static perforation tests. Higher ballistic limits were recorded for specimens containing sand filler. The study showed clear role played by coarse-sized sand filler as a secondary reinforcement in terms of higher energy absorption as compared with nonfilled and specimens containing fine-sized fillers. The investigation successfully characterized behavior of quasi-static test during penetration and perforation of the sharp-tipped indenter as an aid for impact application studies. Residual frictional load in the specimens containing sand filler constituted considerable portion of load bearing during perforation in quasi-static tests. Delaminations followed by fiber and matrix fracture were major failure mode in high-velocity tests and the main energy absorbing mechanism in thick-walled plates, whereas in quasi-static tests the failures were more of matrix fracture and fiber sliding. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers [source]