Home About us Contact
|
Home About us Contact | ||
|
|
||
Coating Procedure (coating + procedure)
Selected AbstractsOne-Step, Painting-Like Coating Procedures To Make Surfaces Highly and Permanently BactericidalBIOTECHNOLOGY PROGRESS, Issue 2 2006Daewon Park Previously we found that covalent attachment of long-chained, moderately hydrophobic polycations to surfaces of solid objects renders the latter permanently bactericidal. Herein we replaced such surface-specific, multistep immobilization techniques with a single-step, general procedure akin to common painting. Glass or polyethylene slides were briefly dipped into organic solutions of certain optimally hydrophobic N -alkyl-PEI (where PEI stands for branched 750-kDa polyethylenimine) polycations, followed by solvent evaporation. The resultant polycation-coated slides were able to kill on contact all of the encountered bacterial cells, whether the Gram-positive human pathogen Staphylococcus aureus or its Gram-negative brethren Escherichia coli. This biocidal effect was found not to be caused by N -alkyl-PEI molecules leached from the surface. Further examination of the mechanism of this bactericidal action suggested that the surface-deposited N -alkyl-PEI kills bacteria by rupturing their cellular membranes. This conclusion was further supported by studies in which the molecular weight of PEI and the hydrophobicity of the alkyl moiety were varied. [source] Rapid capillary electrophoresis time-of-flight mass spectrometry separations of peptides and proteins using a monoquaternarized piperazine compound (M7C4I) for capillary coatingsELECTROPHORESIS, Issue 8 2008Anisa Elhamili Abstract A monoquaternarized piperazine, 1-(4-iodobutyl) 4-aza-1-azoniabicyclo[2,2,2] octane iodide (M7C4I), has been evaluated as a surface derivatization reagent for CE in combination with TOF MS for the analysis of proteins, peptides, and protein digests. The M7C4I piperazine, at alkaline pH, forms a covalent bond via alkylation of the ionized silanols producing a cationic surface with a highly stable and reversed EOF. The obtained surface yields rapid separations (less than 5,min) of peptides and proteins at acidic pH with high separation efficiencies (up to 1.1×106 plates/m for peptides and up to 1.8×106 plates/m for proteins) and no observed bleeding of the coating reagent into the mass spectrometer. The simplicity of the coating procedure also enables fast (2,min) regeneration of the surface, if necessary. This is useful in the analysis of complex samples in order to prevent possible memory effects. The potential of using M7C4I-coated capillaries for MS analysis of complex samples is demonstrated by the separation of peptides, proteins, and protein digests. Even more, the spectacular thing in which large intact proteins with molecular masses over 0.5,MDa could be separated. The coating showed good ability to handle these large proteins with high efficiency and retained peak shape as demonstrated by separation of IgG1 (150,kDa) and thyroglobulin (669,kDa). [source] Capillary electrophoresis using copolymers of different composition as physical coatings: A comparative studyELECTROPHORESIS, Issue 5-6 2006Guillaume L. Erny Abstract In this work, a comparative study on the use of different polymers as physically adsorbed coatings for CE is presented. It is demonstrated that the use of ad hoc synthesized polymers as coatings allows tailoring the EOF in CE increasing the flexibility of this analytical technique. Namely, different polymers were synthesized at our laboratory using different percentages of ethylpyrrolidine methacrylate (EpyM) and N,N -dimethylacrylamide (DMA). Thus, by modifying the percentage of EpyM and DMA monomers it is possible to manipulate the positive charge of the copolymer, varying the global electrical charge on the capillary wall and with that the EOF. These coated capillaries are obtained by simply flushing a given EpyM,DMA aqueous solution into bare silica capillaries. It is shown that by using these coated capillaries at adequate pHs, faster or more resolved CE separations can be achieved depending on the requirements of each analysis. Moreover, it is demonstrated that these coated capillaries reduce the electrostatic adsorption of basic proteins onto the capillary wall. Furthermore, EpyM,DMA coatings allow the reproducible chiral separation of enantiomers through the partial filling technique (PFT). The EpyM,DMA coated capillaries are demonstrated to provide reproducible EOF values independently of the pH and polymer composition with%RSD values lower than 2% for the same day. It is also demonstrated that the coating procedure is reproducible between capillaries. The compatibility of this coating protocol with CE in microchips is discussed. [source] Multilayer poly(vinyl alcohol)-adsorbed coating on poly(dimethylsiloxane) microfluidic chips for biopolymer separationELECTROPHORESIS, Issue 1 2005Dapeng Wu Abstract A poly(dimethylsiloxane) (PDMS) microfluidic chip surface was modified by multilayer-adsorbed and heat-immobilized poly(vinyl alcohol) (PVA) after oxygen plasma treatment. The reflection absorption infrared spectrum (RAIRS) showed that 88% hydrolyzed PVA adsorbed more strongly than 100% hydrolyzed one on the oxygen plasma-pretreated PDMS surface, and they all had little adsorption on original PDMS surface. Repeating the coating procedure three times was found to produce the most robust and effective coating. PVA coating converted the original PDMS surface from a hydrophobic one into a hydrophilic surface, and suppressed electroosmotic flow (EOF) in the range of pH 3,11. More than 1 000,000 plates/m and baseline resolution were obtained for separation of fluorescently labeled basic proteins (lysozyme, ribonuclease B). Fluorescently labeled acidic proteins (bovine serum albumin, ,-lactoglobulin) and fragments of dsDNA ,X174 RF/HaeIII were also separated satisfactorily in the three-layer 88% PVA-coated PDMS microchip. Good separation of basic proteins was obtained for about 70 consecutive runs. [source] Lithium Batteries: (Adv. Funct.ADVANCED FUNCTIONAL MATERIALS, Issue 10 2009Mater. The cover picture is a scanning electron microscopy image of uncoated and 0.5 wt% TiO2 nanoparticle-coated LiCoO2 cathode particles, which are investigated in the research and development of lithium rechargeable batteries that require high power, high capacity, and high safety. TiO2 nanoparticles with sizes below 100 nm are mixed with LiCoO2 particles with an average particle size of 20,µm in a rotating jar at 200 rpm. The mixed particles are then fired at 1000°C for 5 h in air. The uncoated and 0.5 wt% coated particles show similar surface morphologies to each other. Despite the use of dry coating, Ti atoms appear to distribute uniformly throughout the particles. The advantage of this method is a simplified and cost-effective coating procedure, and these electrochemical enhancements can lead to versatile potential applications of the batteries, and provide breakthroughs in the power supply of mobile electronics. [source] A Simple, One-Step Approach to Durable and Robust Superhydrophobic Textiles,ADVANCED FUNCTIONAL MATERIALS, Issue 22 2008Jan Zimmermann Abstract Superhydrophobic textile fabrics are prepared by a simple, one-step gas phase coating procedure by which a layer of polymethylsilsesquioxane nanofilaments is grown onto the individual textile fibers. A total of 11 textile fabrics made from natural and man made fibers are successfully coated and their superhydrophobic properties evaluated by the water shedding angle technique. A thorough investigation of the commercially relevant poly(ethylene terephthalate) fabric reveals an unparalleled long-term water resistance and stability of the superhydrophobic effect. Because of the special surface geometry generated by the nanoscopic, fibrous coating on the microscopic, fibrous textiles, the coated fabric remains completely dry even after two months of full immersion in water and stays superhydrophobic even after continuous rubbing with a skin simulating friction partner under significant load. Furthermore, important textile parameters such as tensile strength, color, and haptics are unaffected by the silicone nanofilament coating. For the first time, an in-depth characterization of the wetting properties, beyond simple contact angle measurements, as well as a thorough evaluation of the most important textile parameters is performed on a superhydrophobic fabric, which reveals a true potential for application. [source] | ||||||||||