|
| ||
|
|
||
Acquisition Geometry (acquisition + geometry)
Selected AbstractsDistance separated simultaneous sweeping, for fast, clean, vibroseis acquisitionGEOPHYSICAL PROSPECTING, Issue 1 2010Jack Bouska ABSTRACT Distance separated simultaneous sweeping DS3 is a new vibroseis technique that produces independent records, uncontaminated by simultaneous source interference, for a range of offsets and depths that span all target zones of interest. Use of DS3 on a recent seismic survey in Oman, resulted in a peak acquisition rate of 1024 records per hour. This survey employed 15 vibrators, with a distance separation of 12 km between simultaneous active sources, recorded by 8000 active channels across 22 live lines in an 18.5 km × 11 km receiver patch. Broad distribution of simultaneous sources, across an adequately sized recording patch, effectively partitions the sensors so that each trace records only one of the simultaneous sources. With proper source separation, on a scale similar to twice the maximum usable source receiver offset, wavefield overlap occurs below the zone of interest. This yields records that are indistinguishable from non-simultaneous source data, within temporal and spatial limits. This DS3 technique may be implemented using a wide variety of acquisition geometries, optimally with spatially large recording patches that enable appropriate source separation distances. DS3 improves acquisition efficiency without data quality degradation, eliminating the requirement for special data processing or noise attenuation. [source] Infilling of sparse 3D data for 3D focusing operator estimationGEOPHYSICAL PROSPECTING, Issue 6 2004M.J. Van De Rijzen ABSTRACT Seismic migration can be formulated in terms of two consecutive downward extrapolation steps: refocusing the receivers and refocusing the sources. Applying only the first focusing step with an estimate of the focusing operators results in a common focal point (CFP) gather for each depth point at a reflecting boundary. The CFP gathers, in combination with the estimates of the focusing operators, can be used in an iterative procedure to obtain the correct operators. However, current 3D seismic data acquisition geometries do not contain the dense spatial sampling required for calculation of full 3D CFP gathers. We report on the construction of full 3D CFP gathers using a non-full 3D acquisition geometry. The proposed method uses a reflector-orientated data infill procedure based on the azimuthal redundancy of the reflection data. The results on 3D numerical data in this paper show that full 3D CFP gathers, which are kinematically and dynamically correct for the target event, can be obtained. These gathers can be used for iterative updating of the 3D focusing operators. [source] High-resolution seismic imaging in deep sea from a joint deep-towed/OBH reflection experiment: application to a Mass Transport Complex offshore NigeriaGEOPHYSICAL JOURNAL INTERNATIONAL, Issue 3 2010S. Ker SUMMARY We assess the feasibility of high-resolution seismic depth imaging in deep water based on a new geophysical approach involving the joint use of a deep-towed seismic device (SYSIF) and ocean bottom hydrophones (OBHs). Source signature measurement enables signature deconvolution to be used to improve the vertical resolution and signal-to-noise ratio. The source signature was also used to precisely determine direct traveltimes that were inverted to relocate source and receiver positions. The very high accuracy of the positioning that was obtained enabled depth imaging and a stack of the OBH data to be performed. The determination of the P -wave velocity distribution was realized by the adaptation of an iterative focusing approach to the specific acquisition geometry. This innovative experiment combined with advanced processing succeeded in reaching lateral and vertical resolution (2.5 and 1 m) in accordance with the objectives of imaging fine scale structures and correlation with in situ measurements. To illustrate the technological and processing advances of the approach, we present a first application performed during the ERIG3D cruise offshore Nigeria with the seismic data acquired over NG1, a buried Mass Transport Complex (MTC) interpreted as a debris flow by conventional data. Evidence for a slide nature of a part of the MTC was provided by the high resolution of the OBH depth images. Rigid behaviour may be inferred from movement of coherent material inside the MTC and thrust structures at the base of the MTC. Furthermore, a silt layer that was disrupted during emplacement but has maintained its stratigraphic position supports a short transport distance. [source] Infilling of sparse 3D data for 3D focusing operator estimationGEOPHYSICAL PROSPECTING, Issue 6 2004M.J. Van De Rijzen ABSTRACT Seismic migration can be formulated in terms of two consecutive downward extrapolation steps: refocusing the receivers and refocusing the sources. Applying only the first focusing step with an estimate of the focusing operators results in a common focal point (CFP) gather for each depth point at a reflecting boundary. The CFP gathers, in combination with the estimates of the focusing operators, can be used in an iterative procedure to obtain the correct operators. However, current 3D seismic data acquisition geometries do not contain the dense spatial sampling required for calculation of full 3D CFP gathers. We report on the construction of full 3D CFP gathers using a non-full 3D acquisition geometry. The proposed method uses a reflector-orientated data infill procedure based on the azimuthal redundancy of the reflection data. The results on 3D numerical data in this paper show that full 3D CFP gathers, which are kinematically and dynamically correct for the target event, can be obtained. These gathers can be used for iterative updating of the 3D focusing operators. [source] Fracture characterization from walkaround VSPsGEOPHYSICAL PROSPECTING, Issue 6 2003Steve Horne ABSTRACT A walkaround VSP is a novel acquisition geometry comprising multiple sources azimuthally distributed around a fixed multi-component receiver at approximately the same offset. Such a configuration allows the robust measurement of fracture-induced anisotropy by the analysis of certain seismic attributes with respect to azimuth. [source] A comparative study on interpolation methods for controlled cardiac CTINTERNATIONAL JOURNAL OF IMAGING SYSTEMS AND TECHNOLOGY, Issue 2 2007Deepak Bharkhada Abstract Bai et al. recently proposed to acquire random fan-beam/cone-beam projections with a linear/planar detector from a circular scanning locus for controlled cardiac computed tomography (CT). After specifying a uniform acquisition geometry required by FBP (filtration-backprojection), we rebin the random fan-beam/cone-beam data via nearest-neighbor, quadrilateral and triangle-based linear interpolation methods. The fan-beam and parallel-beam FBP algorithms are employed for rebinned fan-beam projections. The FDK (Feldkamp,Davis,Kress) and t-FDK (tent-FDK) methods are employed for rebinned cone-beam data. Also, nonuniform weighting fan-beam/FDK methods are used to reconstruct without rebinning. As a benchmark, the images are reconstructed using uniform weighting fan-beam/FDK method from data collected at the specified uniform grid. To evaluate the different methods, effects of increasing the number of projections and adding Poisson noise are studied. The root mean square error (RMSE) is used to quantify the image quality by numerical tests with the cardiac phantom. Our results show that it is helpful to perform data interpolation for improvements of the image quality in controlled cardiac CT from random projections. Our simulations indicate that triangular interpolation gives the most satisfactory result for improved image quality whereas quadrilateral interpolationgives the best noise performance. © 2007 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 17, 91,98, 2007 [source] | ||||||||||