|
| ||
|
|
||
Cellulose Film (cellulose + film)
Selected AbstractsStructure and properties of cellulose nanocomposite films containing melamine formaldehydeJOURNAL OF APPLIED POLYMER SCIENCE, Issue 4 2007Marielle Henriksson Abstract Films of high Young's modulus and low density are of interest for application as loudspeaker membranes. In the present study nanocomposite films were prepared from microfibrillated cellulose (MFC) and from MFC in combination with melamine formaldehyde (MF). The prepared materials were studied with respect to structure as well as physical and mechanical properties. Studies in SEM and calculation of porosity showed that these materials have a dense paper-like structure. The moisture sorption isotherms were measured and showed that moisture content decreased in the presence of MF. Mechanical properties were studied by dynamical mechanical thermal measurements as well as by tensile tests. Cellulose films showed an average Young's modulus of 14 GPa while the nanocomposites showed an average Young's modulus as high as 16.6 GPa and average tensile strength as high as 142 MPa. By controlling composition and structure, the range of properties of these materials can extend the property range available for existing materials. The combination of comparatively high mechanical damping and high sound propagation velocity is of technical interest. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007 [source] Preparation and properties of the single-walled carbon nanotube/cellulose nanocomposites using N -methylmorpholine- N -oxide monohydrateJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2010Dong-Hun Kim Abstract Single-walled carbon nanotube (SWNT)/cellulose nanocomposite films were prepared using N -methylmorpholine- N -oxide (NMMO) monohydrate as a dispersing agent for the acid-treated SWNTs (A-SWNTs) as well as a cellulose solvent. The A-SWNTs were dispersed in both NMMO monohydrate and the nanocomposite film (as confirmed by scanning electron microscopy) because of the strong hydrogen bonds of the A-SWNTs with NMMO and cellulose. The mechanical properties, thermal properties, and electric conductivity of the nanocomposite films were improved by adding a small amount of the A-SWNTs to the cellulose. For example, by adding 1 wt % of the A-SWNTs to the cellulose, tensile strain at break point, Young's modulus, and toughness increased , 5.4, , 2.2, and , 6 times, respectively, the degradation temperature increased to 9°C as compared with those of the pure cellulose film, and the electric conductivities at , (the wt % of A-SWNTs in the composite) = 1 and 9 were 4.97 × 10,4 and 3.74 × 10,2 S/cm, respectively. Thus, the A-SWNT/cellulose nanocomposites are a promising material and can be used for many applications, such as toughened Lyocell fibers, transparent electrodes, and soforth. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Effects of vanillin and plasticizer on properties of chitosan-methyl cellulose based filmJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2008Jurmkwan Sangsuwan Abstract Chitosan-methyl cellulose based films which incorporatate vanillin as an antimicrobial agent and polyethylene glycol 400 (PEG) as a plasticizer were developed in this study. The effects of vanillin and plasticizer concentration on mechanical, barrier, optical, and thermal properties of chitosan-methyl cellulose film were evaluated. When the vanillin concentration was increased at a given PEG level, film flexibility decreased while tensile strength increased slightly. Vanillin increased the barrier to oxygen but not water vapor. Increasing vanillin content resulted in less transparency and a more yellowish tint. The bulky nature of vanillin reduced film crystallization. When PEG concentration was increased at a given vanillin level, it resulted in greater film flexibility but reduced film strength. Water vapor permeability (WVP) and oxygen permeability (OP) increased with increase in PEG content. PEG contributed less to the opacity, yellowness, and crystallization of the film than did vanillin. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Structure and Properties of CdS/Regenerated Cellulose NanocompositesMACROMOLECULAR MATERIALS & ENGINEERING, Issue 10 2005Dong Ruan Abstract Summary: Novel inorganic-organic hybrid materials composed of cadmium sulfide (CdS) semiconducting nanocrystals and regenerated cellulose (RC) were prepared by using in situ synthesizing method. Cellulose was dissolved in a 6 wt.-% NaOH/4 wt.-% urea/thiourea aqueous solution at low temperature followed by addition of cadmium chloride (CdCl2), resulting that the CdS nanocrystals were successfully grown in situ in the cellulose solution. Nanocomposite films containing homogeneous CdS nanoparticles were obtained by casting the resulting solution. Their structure and optical properties were characterized by X-ray photoelectron spectroscopy, wide-angle X-ray diffraction, thermogravimetry analysis, dynamic mechanical analysis, atomic force microscopy, transmittance electronic microscope, UV-vis spectroscopy, and photoluminescence spectroscopy. The experimental results confirmed that the CdS nanocrystalline existed in the composite films, and cellulose matrix provided a confined medium for CdS particle growth in uniform size. The CdS/RC composites showed narrow emission in photoluminescence spectra, and their optical absorbance in the UV range was higher than that of the cellulose film without CdS. This work provided a simple method to prepare cellulose functional materials in NaOH/urea aqueous solution. Photoluminescence of CdS/RC nanocomposites and TEM image of CdS nanocrystals dispersed in RC matrix. [source] Effect of covalent bonds on the mechanical properties of a multi-walled carbon nanotube/cellulose compositePOLYMER INTERNATIONAL, Issue 8 2010Sungryul Yun Abstract A multi-walled carbon nanotube (MWCNT)/cellulose composite was synthesized to improve the mechanical strength of regenerated cellulose film. N,N -carbonyldiimidazole was mixed with functionalized MWCNTs and sonicated at 60 °C for 12 h. The resulting MWCNT-imidazolide was mixed with cellulose solution, and reacted at various temperatures for various times. The occurrence of covalent bonds between MWCNTs and cellulose was investigated using Fourier transform infrared spectroscopy and Raman spectroscopy. According to mechanical tensile tests, Young's modulus of the MWCNT/cellulose composite was found to be 11.2 GPa, an increase of approximately 110% with respect to regenerated cellulose film. Copyright © 2010 Society of Chemical Industry [source] | ||||||||||