|
| ||
|
|
||
CB Particles (cb + particle)
Selected AbstractsEffect of morphology on the electric conductivity of binary polymer blends filled with carbon blackJOURNAL OF APPLIED POLYMER SCIENCE, Issue 3 2007Zhongbin Xu Abstract Several carbon black (CB)-filled binary polymer blends were prepared in Haake rheometer. Distribution states of CB and effect of morphology on the electric conductivity of different ternary composites were investigated. Under our experimental condition CB particles located preferentially at the interface between polymethyl methacrylate (PMMA) and polypropylene (PP) in PMMA/PP/CB composites, in high-density polyethylene (HDPE) phase in PP/HDPE/CB composites, and in Nylon6 (PA6) phase in polystyrene (PS)/PA6/CB, PP/PA6/CB, PMMA/PA6/CB, and polyacrylonitrile (PAN)/PA6/CB composites; the ternary composites in which CB particles locate at the interface of two polymer components have the highest electric conductivity when the mass ratio of the two polymers is near to 1 : 1. The ternary composites in which CB particles located preferentially in one polymer have the highest electric conductivity usually when the amount of the polymer component having CB particles is comparatively less than the amount of the polymer component not having CB particles; if the formulations of PS/PA6/CB, PP/PA6/CB, and PMMA/PA6/CB composites equaled and PA6/CB in them is in dispersed phase, PS/PA6/CB composites have the highest electric conductivity and PP/PA6/CB composites have the lowest electric conductivity; suitable amount of PS or PAN in PA6/CB composites increase the electric conductivity due in the formation of a parallel electrocircuit for electrons to transmit. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007 [source] New antistatic charge and electromagnetic shielding effectiveness from conductive epoxy resin/plasticized carbon black compositesPOLYMER COMPOSITES, Issue 2 2008Nadia Abdel Aal Recently, there is an increasing interest in electromagnetic interference shielding due to the rapid increase in electromagnetic pollution and the wide use of commercial and military products. Conducting polymer composites were prepared in the presence of epoxy resin and plasticized carbon black (CB). The structural characteristics of the composites were examined by means of scanning electron microscopy, cross linking density, and interparticle distance among conductive particles. The mechanical properties such as Young's modulus, elongation at break, and hardness of the composites were investigated as a function of CB content. The results indicated that CB could improve the composite microstructure. The higher mechanical behavior than green epoxy can be attributed to the interaction between CB particles and epoxy resin. The conductivity, mobility carriers, and number of charges of the composites at room temperature were found to be dependent on CB content. The applicability of the composites to antistatic charge dissipation was examined. Dependence of the microwave properties of the epoxy/CB composites on the volume fraction of CB particles and frequency were studied. Moreover the permittivity as a function of frequency of the composites was studied. The electromagnetic wave shielding of epoxy/CB composites is dominant by both reflection and absorption. Composites can find applications in antistatic charge dissipation and in suppression of electromagnetic interference and stealth technology. POLYM. COMPOS., 2008. © 2007 Society of Plastics Engineers [source] Hysteresis measurements and dynamic mechanical characterization of functionally graded natural rubber,carbon black compositesPOLYMER ENGINEERING & SCIENCE, Issue 5 2010S.S. Ahankari Functionally graded polymer composites (FGPCs) were prepared by construction based layering method employing natural rubber (NR) as a matrix and carbon black (CB) in graded form. CB particles were graded along the rectangular geometry polymer matrix comprising the variation of particle volume fraction along thickness direction. These FGPCs were characterized through hysteresis measurements and compared with uniformly dispersed polymeric composites (UDPCs) maintaining the same average amount of filler. Dynamic mechanical properties of these FGPCs and UDPCs were also compared. Dynamic mechanical characterization revealed that FGPCs show much higher storage modulus than the corresponding UDPCs for any given combination of stacking sequence. Loss tangent of FGPCs was also observed to be lesser when compared to UDPCs leading to less hysteretic losses followed by lesser heat buildup in the composite. Hysteresis measurements accorded with the results of dynamic mechanical characterization. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers [source] Anisotropy in the electrical behavior of immiscible polypropylene/nylon/carbon black blends processed slightly below the melting temperature of the nylonPOLYMER ENGINEERING & SCIENCE, Issue 9 2006J. Zoldan Carbon black (CB) containing polypropylene/nylon (PP/Ny) blends, processed slightly below the melting temperature (Tm) of the dispersed Ny phase, leads to formation of fibrillar Ny phase and electrically anisotropic systems. CB containing PP/Ny blends were compounded (twin screw extruder) and processed (injection molding) slightly below the Tm of dispersed Ny phase at different blending sequences. To establish structure,property relationships scanning electron microscopy, high resolution scanning electron microscopy, differential scanning calorimeter were used and electrical properties were also studied. Addition of CB to binary PP/Ny blends, processed below the Ny Tm, altered the Ny fibrillation process forming an irregular continuous phase, containing the CB particles, rather than the fibrils formed in the PP/Ny blends. Yet, upon changing the processing sequence, i.e., compounding PP and CB and then adding Ny in the injection molding stage, Ny fibrils were attained, maintaining phase continuity, oriented in the flow direction and CB particles preferentially located on their surfaces. Blends exhibiting a fibrillar Ny network covered by CB particles exhibited electrical anisotropy. The Ny fibrils exhibited an additional higher crystalline melting peak and molecular orientation. The composites are conductive in the Ny fibril direction, while insulating in the perpendicular direction. Once the CB is located within both, the Ny and the PP matrix the electrical behavior is isotropic. POLYM. ENG. SCI., 46:1250,1262, 2006. © 2006 Society of Plastics Engineers [source] Production of electrically conductive networks in immiscible polymer blends by chaotic mixingPOLYMER ENGINEERING & SCIENCE, Issue 1 2006Dhawal P. Dharaiya A minor polymer was deformed into lamellar and fibrillar morphological forms in a chaotic mixer, which rendered the resultant immiscible blend electrically conductive along the flow direction. This was demonstrated using a blend consisting of 10 wt% polypropylene (PP), polyamide 6 (PA6), and 1 wt% conductive carbon black (CB) particles. It was found that PP-phase containing CB particles deformed into lamellar and fibrillar morphological forms produced continuous networks in the flow direction, and provided conductivity by double percolation. Breakup of PP fibrils into droplets destroyed the continuous conductive networks, although conductivity was sustained purportedly due to migration of CB particles from the bulk to the surface of closely spaced PP droplets. This was augmented by the formation of much smaller PP droplets in the presence of CB particles. On continued mixing, the blend eventually turned into insulator as CB particles migrated from the polymer,polymer interfaces to PA6 phase. POLYM. ENG. SCI., 46:19,28, 2006. © 2005 Society of Plastics Engineers [source] | ||||||||||