Home About us Contact
|
Home About us Contact | ||
|
|
||
Various Monomers (various + monomer)
Selected AbstractsBlock copolymer preparation by atom transfer radical polymerization under emulsion conditions using a nanoprecipitation techniqueJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 2 2008Delphine Chan-Seng Abstract Living-radical polymerization of acrylates were performed under emulsion atom transfer radical polymerization (ATRP) conditions using latexes prepared by a nanoprecipitation technique previously employed and optimized for the polymerization of styrene. A macroinitiator of poly(n -butyl acrylate) prepared under bulk ATRP was dissolved in acetone and precipitated in an aqueous solution of Brij 98 to preform latex particles, which were then swollen with monomer and heated. Various monomers (i.e. n -butyl acrylate, styrene, and tert -butyl acrylate) were used to swell the particles to prepare homo- and block copolymers from the poly(n -butyl acrylate) macroinitiator. Under these conditions latexes with a relatively good colloidal stability were obtained. Furthermore, amphiphilic block copolymers were prepared by hydrolysis of the tert -butyl groups and the resulting block copolymers were characterized by dynamic light scattering (DLS) and transmission electron microscopy (TEM). The bulk morphologies of the polystyrene- b -poly(n -butyl acrylate) and poly(n -butyl acrylate)- b -poly(acrylic acid) copolymers were investigated by atomic force microscopy (AFM) and small angle X-ray scattering (SAXS). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 625,635, 2008 [source] Atmospheric molding of ionic copolymer MALDI-TOF/MS arrays: A new tool for protein identification/profilingELECTROPHORESIS, Issue 24 2006Alexander Muck Abstract An atmospheric molding protocol has been used to prepare an ionic methacrylate-based copolymer sample support chips for MALDI (pMALDI)-MS by targeting selected groups of various monomers copolymerized during molding, namely, carboxy, sulfo, dimethylalkyamino, and trimethylalkylammonium groups. The new disposable array chips provide analyte-oriented enhancement of protein adsorption to the modified substrates without requiring complicated surface coating or derivatization. The MALDI-MS performance of the new ionic copolymer chips was evaluated for lysozyme, ,-lactoglobulin,A, trypsinogen and carbonic anhydrase,I using washing with solutions prepared in pH or ionic strength steps. On cationic chips, the proteins are washed out at pH lower than their pI values, and on anionic chips at pH higher than their pI values. The ability of the microfabricated pMALDI chip set to selectively adsorb different proteins from real samples and to significantly increase their MS-signal was documented for the transmembrane photosystem,I protein complex from the green alga Chlamydomonas reinhardtii. The proteins were almost exclusively adsorbed according to calculated pI values and grand average of hydropathy (GRAVY) indexes. The new disposable chips reduce manipulation times and increase measurement sensitivity for real-world proteomic samples. The simple atmospheric molding procedure enables additional proteomic operations to be incorporated on disposable MALDI-MS integrated platforms. [source] Living radical photopolymerization induced grafting on thiol,ene based substratesJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 10 2005Sirish K. Reddy Abstract The formation of reactive substrates with iniferter-mediated living radical photopolymerization is a powerful technique for surface modification, which can readily be used to facilitate the incorporation of a variety of surface functionalities. In this research, the photopolymerization kinetics of novel bulk thiol,ene systems have been compared with those of typical acrylate and methacrylate systems when polymerized in the presence of the photoiniferter p -xylene bis(N,N -diethyl dithiocarbamate) (XDT). In the presence of XDT, the thiol,ene systems photopolymerize more quickly than the traditional acrylate and methacrylate systems by one to two orders of magnitude. Fourier transform infrared spectroscopy has been used to monitor the photografting kinetics of various monomers on dithiocarbamate-functionalized surfaces. Furthermore, this technique has been used to evaluate surface-initiation kinetics and to emphasize the influence of bulk substrate properties on grafting kinetics. Finally, photopatterning has been demonstrated on a dithiocarbamate-incorporated thiol,ene substrate with conventional photolithographic techniques. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2134,2144, 2005 [source] Controlled free-radical polymerization of vinyl chlorideJOURNAL OF VINYL & ADDITIVE TECHNOLOGY, Issue 3 2005Dietrich Braun Owing to the importance of poly(vinyl chloride) (PVC) as the second-largest plastic in volume after the polyolefins and above styrene polymers, the control of the free-radical polymerization of vinyl chloride (VC) is of high industrial and academic interest. But still the term "controlled" polymerization is not yet clearly defined. Often it is used for quasi-living polymerizations with equilibrium reactions in the initiation and/or termination step or for the control of the molecular weight distribution (MWD), but it can also be applied to several structural aspects such as stereochemistry, branching, or special technical properties. In the present article, the control of chain growth and chain transfer is discussed. It has been well known for many years that the propagation step in the VC polymerization is terminated to a large degree by the rather frequent and temperature-dependent chain transfer of the growing macromolecules to the monomer. Therefore, the degree of polymerization is strongly governed by the polymerization temperature. However, this transfer step does not result in a controlled or a narrow MWD. By means of free-radical nitroxide-mediated polymerization of VC in suspension, PVC with a narrower MWD can be obtained also at higher polymerization temperatures. The resulting PVC with nitroxide end groups can act as a macro-initiator for various monomers, resulting in two-block copolymers, which are, e.g., interesting compatibilizers in blends with PVC. J. VINYL ADDIT. TECHNOL., 11:86,90, 2005. © 2005 Society of Plastics Engineers [source] Ring-Opening Metathesis Polymerization Based Post-Synthesis Functionalization of Electron Beam Curing Derived Monolithic MediaMACROMOLECULAR RAPID COMMUNICATIONS, Issue 21 2007Rajendar Bandari Abstract Monolithic materials were prepared via electron-beam curing from ethyl methacrylate, trimethylolpropane triacrylate, and norborn-5-ene-2-ylmethyl acrylate. Reaction of the norborn-2-ene groups with either RuCl2(PCy3)2(CHPh) (1) or RuCl2(PCy3)(1,3-dimesityl-4,5-dihydroimidazol-2-inylidene)(CHPh) (2) resulted in the surface attachment of the initiators. The extent of initiator immobilization was found to be substantially higher for 1 than for 2. Reaction of the surface immobilized initiators with various monomers resulted in the desired surface modification of EB-derived monoliths. The amounts of grafted monomer were determined by elemental analysis and ICP-OES. [source] Experimental Requirements for an Efficient Control of Free-Radical Polymerizations via the Reversible Addition-Fragmentation Chain Transfer (RAFT) Process,MACROMOLECULAR RAPID COMMUNICATIONS, Issue 9 2006Arnaud Favier Abstract Summary: Reversible addition-fragmentation chain transfer (RAFT) polymerization is a recent and very versatile controlled radical polymerization technique that has enabled the synthesis of a wide range of macromolecules with well-defined structures, compositions, and functionalities. The RAFT process is based on a reversible addition-fragmentation reaction mediated by thiocarbonylthio compounds used as chain transfer agents (CTAs). A great variety of CTAs have been designed and synthesized so far with different kinds of substituents. In this review, all of the CTAs encountered in the literature from 1998 to date are reported and classified according to several criteria : i) the structure of their substituents, ii) the various monomers that they have been polymerized with, and iii) the type of polymerization that has been performed (solution, dispersed media, surface initiated, and copolymerization). Moreover, the influence of various parameters is discussed, especially the CTA structure relative to the monomer and the experimental conditions (temperature, pressure, initiation, CTA/initiator ratio, concentration), in order to optimise the kinetics and the efficiency of the molecular-weight-distribution control. Schematic of the RAFT polymerization. [source] | ||||||||||