			Home About us Contact

Time-lapse Survey (time-lapse + survey)

Distribution by Scientific Domains

Earth and Environmental Science	100%

Selected Abstracts

Processing, modelling and predicting time-lapse effects of overpressured fluid-injection in a fractured reservoir

GEOPHYSICAL JOURNAL INTERNATIONAL, Issue 2 2002
Erika Angerer
Summary Time-lapse seismology is important for monitoring subsurface pressure changes and fluid movements in producing hydrocarbon reservoirs. We analyse two 4-D, 3C onshore surveys from Vacuum Field, New Mexico, USA, where the reservoir of interest is a fractured dolomite. In Phase VI, a time-lapse survey was acquired before and after a pilot tertiary-recovery programme of overpressured CO2 injection, which altered the fluid composition and the pore-fluid pressure. Phase VII was a similar time-lapse survey in the same location but with a different lower-pressure injection regime. Applying a processing sequence to the Phase VI data preserving normal-incidence shear-wave anisotropy (time-delays and polarization) and maximizing repeatability, interval-time analysis of the reservoir interval shows a significant 10 per cent change in shear-wave velocity anisotropy and 3 per cent decrease in the P -wave interval velocities. A 1-D model incorporating both saturation and pressure changes is matched to the data. The saturation changes have little effect on the seismic velocities. There are two main causes of the time-lapse changes. Any change in pore-fluid pressures modifies crack aspect ratios. Additionally, when there are overpressures, as there are in Phase VI, there is a 90° change in maximum impedance directions, and the leading faster split shear wave, instead of being parallel to the crack face as it is for low pore-fluid pressures, becomes orthogonal to the crack face. The anisotropic poro-elasticity (APE) model of the evolution of microcracked rock, calculates the evolution of cracked rock to changing conditions. APE modelling shows that at high overburden pressures only nearly vertical cracks, to which normal incidence P waves are less sensitive than S waves, remain open as the pore-fluid pressure increases. APE modelling matches the observed time-lapse effects almost exactly demonstrating that shear-wave anisotropy is a highly sensitive diagnostic of pore-fluid pressure changes in fractured reservoirs. In this comparatively limited analysis, APE modelling of fluid-injection at known pressure correctly predicted the changes in seismic response, particularly the shear-wave splitting, induced by the high-pressure CO2 injection. In the Phase VII survey, APE modelling also successfully predicted the response to the lower-pressure injection using the same Phase VI model of the cracked reservoir. The underlying reason for this remarkable predictability of fluid-saturated reservoir rocks is the critical nature and high crack density of the fluid-saturated cracks and microcracks in the reservoir rock, which makes cracked reservoirs critical systems. [source]

Full waveform inversion of seismic waves reflected in a stratified porous medium

GEOPHYSICAL JOURNAL INTERNATIONAL, Issue 3 2010
Louis De Barros
SUMMARY In reservoir geophysics applications, seismic imaging techniques are expected to provide as much information as possible on fluid-filled reservoir rocks. Since seismograms are, to some degree, sensitive to the mechanical parameters and fluid properties of porous media, inversion methods can be devised to directly estimate these quantities from the waveforms obtained in seismic reflection experiments. An inversion algorithm that uses a generalized least-squares, quasi-Newton approach is described to determine the porosity, permeability, interstitial fluid properties and mechanical parameters of porous media. The proposed algorithm proceeds by iteratively minimizing a misfit function between observed data and synthetic wavefields computed with the Biot theory. Simple models consisting of plane-layered, fluid-saturated and poro-elastic media are considered to demonstrate the concept and evaluate the performance of such a full waveform inversion scheme. Numerical experiments show that, when applied to synthetic data, the inversion procedure can accurately reconstruct the vertical distribution of a single model parameter, if all other parameters are perfectly known. However, the coupling between some of the model parameters does not permit the reconstruction of several model parameters at the same time. To get around this problem, we consider composite parameters defined from the original model properties and from a priori information, such as the fluid saturation rate or the lithology, to reduce the number of unknowns. Another possibility is to apply this inversion algorithm to time-lapse surveys carried out for fluid substitution problems, such as CO2 injection, since in this case only a few parameters may vary as a function of time. We define a two-step differential inversion approach which allows us to reconstruct the fluid saturation rate in reservoir layers, even though the medium properties are poorly known. [source]

Controlled sources for shear-wave surveys in mines

GEOPHYSICAL PROSPECTING, Issue 3 2000
Gordon M. Holmes
The ability to analyse shear-wave anisotropy in a mine environment is greatly aided by using multiple source orientations of a reproducible, impulsive shear-wave source. The analysis of what is probably the first controlled source shear-wave experiment in a mine environment demonstrates clearly that shear-wave polarizations and time delays between split shear-wave arrivals are reliably measured because of the use of multiple source orientations rather than a single shear-wave source. Reliability is further aided by modelling the shear-wave source radiation pattern, which allows for the unequivocal discrimination between seismic raypaths where shear-wave splitting did and did not occur. The analysis also demonstrates the great importance of high reproducibility of the seismic source for the use of shear waves in time-lapse surveys to monitor changes in a rockmass. [source]