Home About us Contact
|
Home About us Contact | ||
|
|
||
Spherical Particles (spherical + particle)
Selected AbstractsSilica Supported Submicron SiO2@Y2SiO5:Eu3+ and SiO2@Y2SiO5:Ce3+/Tb3+ Spherical Particles with a Core,Shell Structure: Sol,Gel Synthesis and CharacterizationEUROPEAN JOURNAL OF INORGANIC CHEMISTRY, Issue 18 2006Cuikun Lin Abstract X1 -Y2SiO5:Eu3+ and X1 -Y2SiO5:Ce3+ and/or Tb3+ phosphor layers have been coated on nonaggregated, monodisperse, submicron spherical SiO2 particles by a sol,gel process, followed by surface reaction at high temperature (1000 °C), to give core/shell structured SiO2@Y2SiO5:Eu3+ and SiO2@Y2SiO5:Ce3+/Tb3+ particles. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), TEM, photoluminescence (PL), low voltage cathodoluminescence (CL), and time-resolved PL spectra and lifetimes are used to characterize these materials. The XRD results indicate that X1 -Y2SiO5 layers have been successfully coated on the surface of SiO2 particles, as further verified by the FESEM and TEM images. The PL and CL studies suggest that SiO2@Y2SiO5:Eu3+, SiO2@Y2SiO5:Tb3+ (or Ce3+/Tb3+), and SiO2@Y2SiO5:Ce3+ core/shell particles exhibit red (Eu3+, 613 nm: 5D0,7F2), green (Tb3+, 542 nm: 5D4,7F5), or blue (Ce3+, 450 nm: 5d-4f) luminescence, respectively. PL excitation, emission, and time-resolved spectra demonstrate that there is an energy transfer from Ce3+ to Tb3+ in the SiO2@Y2SiO5:Ce3+,Tb3+ core/shell particles. (© Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2006) [source] Size Measurement of Very Small Spherical Particles by Mie Scattering Imaging (MSI)PARTICLE & PARTICLE SYSTEMS CHARACTERIZATION, Issue 5 2004Arne Graßmann Abstract The Mie Scattering Imaging method (MSI) gathers out-of-focus images of dispersed spherical particles present in a laser light sheet and extracts the individual particle diameter from these images. The general idea of the method has been around for more than a decade and a number of papers has dealt with it over recent years. Our work focuses on small particle sizes from 20 ,m down to 2 ,m, a range which has not been tackled so far although it is of great importance in particle systems. We present an optical set-up with a special arrangement of camera lenses that allows to work in this range. An evaluation algorithm based on correlation of the experimental optical information with theoretical Mie scattering was found to give the most accurate results for particle sizing. Besides accuracy measurements on solid spheres the versatility of the method is demonstrated by an example of transient droplet growth between 2,7,,m. [source] An innovative method to obtain porous PLLA scaffolds with highly spherical and interconnected poresJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2008Cédryck Vaquette Abstract Scaffolding is an essential issue in tissue engineering and scaffolds should answer certain essential criteria: biocompatibility, high porosity, and important pore interconnectivity to facilitate cell migration and fluid diffusion. In this work, a modified solvent casting-particulate leaching out method is presented to produce scaffolds with spherical and interconnected pores. Sugar particles (200,300 ,m and 300,500 ,m) were poured through a horizontal Meker burner flame and collected below the flame. While crossing the high temperature zone, the particles melted and adopted a spherical shape. Spherical particles were compressed in plastic mold. Then, poly- L -lactic acid solution was cast in the sugar assembly. After solvent evaporation, the sugar was removed by immersing the structure into distilled water for 3 days. The obtained scaffolds presented highly spherical interconnected pores, with interconnection pathways from 10 to 100 ,m. Pore interconnection was obtained without any additional step. Compression tests were carried out to evaluate the scaffold mechanical performances. Moreover, rabbit bone marrow mesenchymal stem cells were found to adhere and to proliferate in vitro in the scaffold over 21 days. This technique produced scaffold with highly spherical and interconnected pores without the use of additional organic solvents to leach out the porogen. © 2007 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008 [source] In-Flight-Melted Soda-Lime-Silica Glass by RF Induction Thermal PlasmaJOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 12 2008Fuji Funabiki Granulated raw materials with a particle size of 20,80 ,m were prepared from a slurry of Na2CO3, CaCO3, and SiO2 (quartz) by the spray-dry method, and injected with carrier gas into a radio-frequency induction thermal plasma. Spherical particles 5,60 ,m in size were obtained and analyzed. Thermo-gravimetric analysis and X-ray diffraction analysis showed that during the short flight of the order of milliseconds, all carbonates were decomposed and >95% quartz was reacted into a noncrystalline state. Glass transition was clearly observed by differential thermal analysis. Increase of the carrier gas from 3 to 6 L/min led to a decrease in the volatilization ratio of Na2O from 46% to 18% with a slight decrease of the reaction ratio of quartz in trade balance. Electron probe microanalysis showed that the volatilization could be attributed to an excess heating of small particles <30 ,m, and suppression by the increase of carrier gas. [source] Solution-Based Synthesis of Submicrometer ZrB2 and ZrB2,TaB2JOURNAL OF THE AMERICAN CERAMIC SOCIETY, Issue 5 2008Yanli Xie Zirconium diboride and a zirconium diboride/tantalum diboride mixture were synthesized by solution-based processing. Zirconium n -propoxide was refluxed with 2,4-pentanedione to form zirconium diketonate. This compound hydrolyzed in a controllable fashion to form a zirconia precursor. Boria and carbon precursors were formed via solution additions of phenol,formaldehyde and boric acid, respectively. Tantalum oxide precursors were formed similarly as zirconia precursors, in which tantalum ethoxide was used. Solutions were concentrated, dried, pyrolyzed (800°,1100°C, 2 h, flowing argon), and exposed to carbothermal reduction heat treatments (1150°,1800°C, 2 h, flowing argon). Spherical particles of 200,600 nm for pure ZrB2 and ZrB2,TaB2 mixtures were formed. [source] Analysis of electrokinetic transport of a spherical particle in a microchannelELECTROPHORESIS, Issue 4 2007Harikrishnan N. Unni Abstract Electrokinetically driven microfluidic devices that are used for biological cell/particle manipulation (e.g., cell sorting, separation) involve electrokinetic transport of these particles in microchannels whose dimension is comparable with particles' size. This paper presents an analytical study on electrokinetic transport of a charged spherical particle in a charged parallel-plate microchannel. Under the thin electric double-layer assumption, solutions in closed-form solutions for the particle velocity and disturbed electrical and fluid velocity fields are obtained for plane-symmetric (along the channel centerline) and asymmetric (off the channel centerline) motions of a sphere in a parallel-plate microchannel. The effects of relative particle size and eccentricity (i.e., off the centerline distance) on a particle's translational and rotational velocities are analyzed. [source] Modelling, identification, and control of a spherical particle trapped in an optical tweezerINTERNATIONAL JOURNAL OF ROBUST AND NONLINEAR CONTROL, Issue 16 2005A. Ranaweera Abstract We provide an introduction to modelling, identification, and control of a spherical particle trapped in an optical tweezer. The main purpose is to analyse the properties of an optical tweezer from a control systems point of view. By representing the non-inertial dynamics of a trapped particle using a stochastic differential equation, we discuss probability distributions and compute first mean exit times. Within the linear trapping region, experimentally measured mean passage times for a 9.6-µm diameter polystyrene bead show close agreement with theoretical calculations. We apply a recursive least squares method to a trapped 9.6-µm diameter polystyrene bead to study the possibility of obtaining faster calibrations of characteristic frequency. We also compare the performance of proportional control, LQG control, and nonlinear control to reduce fluctuations in particle position due to thermal noise. Assuming a cubic trapping force, we use computer simulations to demonstrate that the nonlinear controller can reduce position variance by a factor of 65 for a 1-µm diameter polystyrene bead under typical conditions. Copyright © 2005 John Wiley & Sons, Ltd. [source] Study on the Radius of an Electrical Spherical Micelle: Functional Theoretical ApproachCHINESE JOURNAL OF CHEMISTRY, Issue 4 2004Zheng-Wu Wang Abstract For the purpose of eliminating restriction, the Poisson-Boltzmann (PB) equation, which represents the potential of the electrical double layer of spherical micelles, can be solved analytically only under the lower potential condition, a kind of iterative method in functional analysis theory has been used. The radius of the spherical particle can be obtained from the diagram of the second iterative solution of the potential versus the distance from the center of the particle. The influences of the concentration of the ions, the charge number of ions, the aggregation number of the particle, the dielectric constant of solvent and the temperature of system on the radius also have been studied. [source] Effectiveness of Microporous Polysaccharide Hemospheres for Achieving Hemostasis in Mohs Micrographic SurgeryDERMATOLOGIC SURGERY, Issue 6 2004FRCPC, Stephen R. Tan MD Background. Microporous polysaccharide hemospheres consist of controlled-porosity spherical particles manufactured from bioinert plant polysaccharide. Microporous polysaccharide hemospheres facilitate hemostasis by rapidly absorbing the fluid component of blood, concentrating platelets and clotting factors to accelerate blood clotting. Objective. The objective was to compare a microporous polysaccharide hemosphere bandage and electrocautery in achieving hemostasis. Methods. Twenty-four patients with a total of 48 stages of Mohs micrographic surgery were included. Patients were stratified by whether or not they were taking anticoagulant medications. Within each group, patients were randomized to receive either the microporous polysaccharide hemosphere bandage or electrocautery. Outcomes included bleeding through the dressing (early time point) and active bleeding upon dressing removal (late time point). Results. Nineteen patients not taking anticoagulants had 40 stages, of which 18 received the study bandage and 22 received electrocautery. The remaining 5 patients on anticoagulants had 8 stages, of which 4 received the study bandage and 4 received electrocautery. In both total and subgroup analysis, there was a higher incidence of bleeding through the dressing with the study bandage (p<0.05), but no increase in the incidence of active bleeding upon dressing removal (p>0.05). Conclusion. The microporous polysaccharide hemosphere study bandage had an increased incidence of bleeding through the dressing compared to electrocautery, but did not have an increased incidence of active bleeding upon dressing removal. [source] Numerical comparison between Maxwell stress method and equivalent multipole approach for calculation of the dielectrophoretic force in single-cell trapsELECTROPHORESIS, Issue 11 2005Carlos Rosales Abstract This paper presents detailed numerical calculations of the dielectrophoretic force in traps designed for single-cell trapping. A trap with eight planar electrodes is studied for spherical and ellipsoidal particles using the boundary element method (BEM). Multipolar approximations of orders one to three are compared with the full Maxwell stress tensor (MST) calculation of the electrical force on spherical particles. Ellipsoidal particles are also studied, but in their case only the dipolar approximation is available for comparison with the MST solution. The results show that a small number of multipolar terms need to be considered in order to obtain accurate results for spheres, even in the proximity of the electrodes, and that the full MST calculation is only required in the study of nonspherical particles. [source] Separation and recovery of intact gold-virus complex by agarose electrophoresis and electroelution: Application to the purification of cowpea mosaic virus and colloidal gold complexELECTROPHORESIS, Issue 17 2004Carissa M. Soto Abstract Colloidal gold has been coupled to a mutant cowpea mosaic virus (CPMV), which contains 60 cysteine residues on the surface. A purification process was developed to separate the gold-containing viral nanoblocks (VNBs) from the free gold. Agarose electrophoresis was utilized to separate the mixture followed by electroelution of the desired sample to recover the intact virus. Mobility of Au-VNB and free colloidal gold was facilitated by the addition of thioctic acid (TA). 30% of the gold-containing virus was recovered after electroelution as determined by absorbance measurements. Histogram analysis of transmission electron microscopy (TEM) images demonstrated the efficient separation of gold-containing virus from free gold. TEM and scanning electron microscopy (SEM) images indicated that the virus was recovered intact. Monodisperse spherical particles of nominal size of 45 nm were observed under SEM. [source] Microwave Assisted Synthesis of Yb:Y2O3 Based Materials for Laser Source Application,ADVANCED ENGINEERING MATERIALS, Issue 3 2010Anna Luisa Costa Yb:Y2O3 submicrometric particles were synthesized through co-precipitation of Yb and Y nitrate in water. Microwave heating and controlled release of ammonia through urea decomposition at reaction temperature leaded to the formation of disaggregated, monosized spherical particles of carbo-hydroxy-nitrate precursors. Pure crystalline Yb:Y2O3 powder that preserved the described morphology was obtained after calcination in air at 800,°C for 30,min. This powder mixed with commercial alumina powder was used to produce transparent Yb:YAG ceramics. Improved properties in terms of powder morphology and reactivity were presented in comparison with powders obtained by traditional heating. [source] Diffusion of strongly sorbed solutes in soil: a dual-porosity model allowing for slow access to sorption sites and time-dependent sorption reactionsEUROPEAN JOURNAL OF SOIL SCIENCE, Issue 1 2010M. Ptashnyk We use homogenization techniques to derive a dual (or double) porosity model of solute diffusion and reaction in soil, allowing for slow access to sorption sites within micro-aggregates and time-dependent sorption reactions. We give a means for determining the conditions in which micro-scale concentration gradients affect macro-scale gradients and fluxes. We present equations for a unit volume of soil represented as a series of uniformly-spaced, porous spherical particles, containing and surrounded by solution through which solutes diffuse. The methods we use can, in principle, be applied to more complex geometries. We compare the model's predictions with those of the equivalent single porosity model for commonly used boundary conditions. We show that failure to allow for slow access to reaction sites can lead to seriously erroneous results. Slow access has the effect of decreasing the sorption of solute into soil from a source or desorption from soil to a sink. As a result of slow access, the diffusion coefficients of strongly-sorbed solutes measured at the macro-scale will be time-dependent and will depend on the method of measurement. We also show that slow access is more often likely to limit macro-scale diffusion than rates of slow chemical reactions per se. In principle, the unimportance of slow reactions except at periods longer than several weeks of diffusion simplifies modelling because, if slow access is correctly allowed for, sorption can be described with equilibrium relations with an understanding of speciation and rapid sorption-desorption reactions. [source] Full-length prion protein aggregates to amyloid fibrils and spherical particles by distinct pathwaysFEBS JOURNAL, Issue 9 2008Driss El Moustaine As limited structural information is available on prion protein (PrP) misfolding and aggregation, a causative link between the specific (supra)molecular structure of PrP and transmissible spongiform encephalopathies remains to be elucidated. In this study, high pressure was utilized, as an approach to perturb protein structure, to characterize different morphological and structural PrP aggregates. It was shown that full-length recombinant PrP undergoes ,-sheet aggregation on high-pressure-induced destabilization. By tuning the physicochemical conditions, the assembly process evolves through two distinct pathways leading to the irreversible formation of spherical particles or amyloid fibrils, respectively. When the PrP aggregation propensity is enhanced, high pressure induces the formation of a partially unfolded aggregated protein, AggHP, which relaxes at ambient pressure to form amorphous aggregates. The latter largely retain the native secondary structure. On prolonged incubation at high pressure, followed by depressurization, AggHP transforms to a monodisperse population of spherical particles of about 20 nm in diameter, characterized by an essentially ,-sheet secondary structure. When the PrP aggregation propensity is decreased, an oligomeric reaction intermediate, IHP, is formed under high pressure. After pressure release, IHP relaxes to the original native structure. However, on prolonged incubation at high pressure and subsequent depressurization, it transforms to amyloid fibrils. Structural evaluation, using optical spectroscopic methods, demonstrates that the conformation adopted by the subfibrillar oligomeric intermediate, IHP, constitutes a necessary prerequisite for the formation of amyloids. The use of high-pressure perturbation thus provides an insight into the molecular mechanism of the first stages of PrP misfolding into amyloids. [source] High Quality Factor Metallodielectric Hybrid Plasmonic,Photonic CrystalsADVANCED FUNCTIONAL MATERIALS, Issue 12 2010Xindi Yu Abstract A 2D polystyrene colloidal crystal self-assembled on a flat gold surface supports multiple photonic and plasmonic propagating resonance modes. For both classes of modes, the quality factors can exceed 100, higher than the quality factor of surface plasmons (SP) at a polymer,gold interface. The spatial energy distribution of those resonance modes are carefully studied by measuring the optical response of the hybrid plasmonic,photonic crystal after coating with dielectric materials under different coating profiles. Computer simulations with results closely matching those of experiments provide a clear picture of the field distribution of each resonance mode. For the SP modes, there is strong confinement of electromagnetic energy near the metal surface, while for optical modes, the field is confined inside the spherical particles, far away from the metal. Coating of dielectric material on the crystal results in a large shift in optical features. A surface sensor based on the hybrid plasmonic,photonic crystal is proposed, and it is shown to have atomic layer sensitivity. An example of ethanol vapor sensing based on physisorption of ethanol onto the sensor surface is demonstrated. [source] Synthesis of Luminescent ZrO2:Eu3+ Nanoparticles and Their Holographic Sub-Micrometer Patterning in Polymer CompositesADVANCED FUNCTIONAL MATERIALS, Issue 11 2009Tsedev Ninjbadgar Abstract Here, the facile synthesis of fluorescent ZrO2:Eu3+ nanoparticles with luminescence quantum yield of up to 8.7% that can be easily dispersed in organic solvents and utilized for the preparation of organic/inorganic volume holographic gratings is presented. The nanoparticles are prepared through a one-step solvothermal process resulting in spherical particles with a mean size of 4,nm that were highly crystalline directly after the synthesis, without any need for calcination treatment. Detailed luminescence studies of the nanoparticles as a function of Eu3+ content demonstrate that the dopant concentration and its site symmetry play an important role in the emissive properties and lifetime of the luminescent centers. It is shown that the luminescence quantum yield of the colloidal ZrO2:Eu3+ nanoparticles increases with dopant concentration up to a critical concentration of 11 mol% while the luminescence lifetime is shortened from 1.8 to 1.4 ms. Holographic photopolymerization of suitable monomer mixtures containing the luminescent nanoparticles demonstrated the ability to inscribe volume Bragg gratings (refractive index contrast n1 up to 0.011) with light-emissive properties, evidencing the high suitability of this approach for the fabrication of tailored nanomaterials for elaborate and demanding applications. [source] Cover Picture: Composite Silica Spheres with Magnetic and Luminescent Functionalities (Adv. Funct.ADVANCED FUNCTIONAL MATERIALS, Issue 4 2006Mater. Abstract Photographs of a colloidal dispersion of composite nanoparticles with magnetic and luminescent functionalities are shown (left, in column), which are schematically illustrated in the main image. As reported by Salgueiriño-Maceira and co-workers on p.,509, such functionalities are imparted by magnetic and semiconductor nanoparticles within a silica matrix. In the absence of a magnetic field the particles are uniformly dispersed, although they accumulate and can be dragged under the influence of a magnetic field. Their movement can be monitored by their photoluminescence. A new class of highly fluorescent, photostable, and magnetic core/shell nanoparticles in the submicrometer size range has been synthesized from a modified Stöber method combined with the layer-by-layer (LbL) assembly technique. Luminescent magnetic nanoparticles are prepared via two main steps. The first step involves controlled addition of tetraethoxysilane to a dispersion of Fe3O4/,-Fe2O3 nanoparticles, which are thereby homogeneously incorporated as cores into monodisperse silica spheres. The second step involves the LbL assembly of polyelectrolytes and luminescent CdTe quantum dots onto the surfaces of the silica-coated magnetite/maghemite particles, which are finally covered with an outer shell of silica. These spherical particles have a typical diameter of 220,±,10,nm and a saturation magnetization of 1.34,emu,g,1 at room temperature, and exhibit strong excitonic photoluminescence. Nanoparticles with such a core/shell architecture have the added benefit of providing a robust platform (the outer silica shell) for incorporating diverse functionalities into a single nanoparticle. [source] Evaluation of a laser-assisted particle sizing/settling velocity determination techniqueHYDROLOGICAL PROCESSES, Issue 9 2006Dr I. G. Droppo Abstract The use of predictive models for the understanding and management of sediment and contaminant transport generally requires knowledge of particle size and settling velocity. Particle size is often obtained by direct measurements, and the settling velocities are usually predicted using the Stokes' law (or a modification thereof) for single-grained spherical particles. Such measurements and estimates are not satisfactory measures for cohesive sediments, which exist as agglomerated particles called flocs and whose behaviour is significantly different from that of the single-grained particles. Direct measurement of settling velocity and size using optical methods in settling columns has also been employed to improve these predictions; however, the subjectivity in determining which particles are in focus results in unreliable size data. An out-of-focus particle will generally possess a larger size than in reality. This paper evaluates a laser-assisted particle sizing/settling velocity determination technique's ability to eliminate the subjectivity and improve particle-sizing accuracy during settling column experiments. Although the diffraction of light by the translucent standard beads (used for evaluating the technique's accuracy for determining particle size) posed a problem, the results suggest that this technique has potential for assisting researchers to obtain the most accurate settling particle size data possible. Copyright © 2005 John Wiley & Sons, Ltd. [source] Numerical studies of shear banding in interface shear tests using a new strain calculation method,INTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 12 2007Jianfeng Wang Abstract Strain localization is closely associated with the stress,strain behaviour of an interphase system subject to quasi-static direct interface shear, especially after peak stress state is reached. This behaviour is important because it is closely related to deformations experienced by geotechnical composite structures. This paper presents a study using two-dimensional discrete element method (DEM) simulations on the strain localization of an idealized interphase system composed of densely packed spherical particles in contact with rough manufactured surfaces. The manufactured surface is made up of regular or irregular triangular asperities with varying slopes. A new simple method of strain calculation is used in this study to generate strain field inside a simulated direct interface shear box. This method accounts for particle rotation and captures strain localization features at high resolution. Results show that strain localization begins with the onset of non-linear stress,strain behaviour. A distinct but discontinuous shear band emerges above the rough surface just before the peak stress state, which becomes more expansive and coherent with post-peak strain softening. It is found that the shear bands developed by surfaces with smaller roughness are much thinner than those developed by surfaces with greater roughness. The maximum thickness of the intense shear zone is observed to be about 8,10 median particle diameters. The shear band orientations, which are mainly dominated by the rough boundary surface, are parallel with the zero extension direction, which are horizontally oriented. Published in 2007 by John Wiley & Sons, Ltd. [source] Experimental investigation of slip-stick behaviour in granular materialsINTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS, Issue 14 2006Khalid A. Alshibli Abstract This paper presents the results of an experimental programme to study load oscillation in granular materials. Spherical glass beads were used in the investigation. Cylindrical specimens were compressed under axisymmetric triaxial loading condition at 25,100,250 and 400 kPa confining pressures. The test parameters included: (i) particle size; (ii) gradation (uniform versus non-uniform specimens); (iii) confining pressure; (iv) loading rate; and (v) specimen density. In general, a slight post-peak principal stress softening was observed as well as a continuous volume increase (dilation) even at relatively high strains. This appears to be caused by the uniform shape and smooth surface of the spherical particles. Load oscillations were observed in the very small, small, and well-graded beads at each confining pressure. For the medium beads, the oscillations appeared at high confining pressure (250 and 400 kPa), and they did not appear in the large beads. The influences of the confining pressure, loading rate, particle size, gradation and specimen density on load oscillation are presented and discussed. Copyright © 2006 John Wiley & Sons, Ltd. [source] Hydroxypropyl-,-Cyclodextrin-Capped Palladium Nanoparticles: Active Scaffolds for Efficient Carbon-Carbon Bond Forming Cross-Couplings in WaterADVANCED SYNTHESIS & CATALYSIS (PREVIOUSLY: JOURNAL FUER PRAKTISCHE CHEMIE), Issue 14-15 2009Jaqueline Abstract A new approach for the preparation of palladium nanoparticles in water from a renewable source, 2-hydroxypropyl-,-cyclodextrin (,-HPCD), which acts both as a reductant and capping agent, is presented. The palladium nanoparticles were characterized by using dynamic light scattering (DLS), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS), which revealed the formation of spherical particles in the size range of 2,7,nm. Further analysis by Fourier-transform infrared spectroscopy (FT-IR) and 1H,NMR did not show covalent bonds between cyclodextrins and palladium nanoparticles, suggesting that ,-HPCD is only physically adsorbed on the nanoparticle surface, presumably through hydrophobic interactions which limit the mutual coalescence of nanoclusters. The catalytic activity was tested in Suzuki, Heck and Sonogashira reactions in neat water, providing good yields and selectivities of coupling products under very low Pd loadings (0.5,0.01,mol%). Remarkably, the nanocatalyst showed significant stability hence the aqueous phase remained active for four subsequent runs. The combination of a binding site for substrates (the HPCD cavity) and a reactive centre (Pd core) provides a potential to explore functional catalysis in aqueous medium. [source] Particle size distributions from small-angle scattering using global scattering functionsJOURNAL OF APPLIED CRYSTALLOGRAPHY, Issue 4 2004G. Beaucage Control and quantification of particle size distribution is of importance in the application of nanoscale particles. For this reason, polydispersity in particle size has been the focus of many simulations of particle growth, especially for nanoparticles synthesized from aerosols such as fumed silica, titania and alumina. Single-source aerosols typically result in close to a log-normal distribution in size and micrograph evidence generally supports close to spherical particles, making such particles ideal candidates for considerations of polydispersity. Small-angle X-ray scattering (SAXS) is often used to measure particle size in terms of the radius of gyration, Rg, using Guinier's law, as well as particle surface area, S/V, from the Porod constant B and the scattering invariant Q. In this paper, the unified function is used to obtain these parameters and various moments of the particle size distribution are calculated. The particle size obtained from BET analysis of gas adsorption data directly agrees with the moment calculated from S/V. Scattering results are also compared with TEM particle-counting results. The potential of scattering to distinguish between polydisperse single particles and polydisperse particles in aggregates is presented. A generalized index of polydispersity for symmetric particles, PDI = BRg4/(1.62G), where G is the Guinier prefactor, is introduced and compared with other approaches to describe particle size distributions in SAXS, specifically the maximum-entropy method. [source] In-situ small-angle scattering study on the formation of a nanocrystalline soft-magnetic alloyJOURNAL OF APPLIED CRYSTALLOGRAPHY, Issue 3-1 2000D. R. Dos Santos A detailed study is presented on the nanocrystallization of the amorphous alloy Fe86Zr7Cu 1B6 (indices indicate at. %). Melt-spun ribbons were rapidly annealed by Joule heating, and the electrical resistance showed strong variations during thermal treatment. X-ray diffraction patterns indicate that these variations are related to the nucleation and growth of ,-Fe nanocrystals, and from peak profile analysis we obtained the average grain size and crystalline volume fraction for different annealing currents. The disorder-order transition was studied by in-situ small-angle X-ray scattering during conventional furnace treatments. SAXS intensity evolution for different temperatures, both below and above the crystallization temperature of the alloy, showed that a fast atomic rearrangement leads to the formation of atomic clusters before crystallization. The evolution of the size distribution function of these clusters as a function of time and temperature was obtained assuming a polydisperse system of spherical particles. [source] Controlled size chitosan nanoparticles as an efficient, biocompatible oligonucleotides delivery systemJOURNAL OF APPLIED POLYMER SCIENCE, Issue 4 2010Romila Manchanda Abstract Polymeric nanoparticles of chitosan crosslinked with glutaraldehyde have been prepared using reverse micellar system. An optically clear solution was obtained on redispersing these nanoparticles in aqueous buffer. The nanoparticles were characterized for their size and surface morphology employing dynamic laser scattering (DLS) and transmission electron microscopy (TEM). The TEM images showed spherical particles with smooth surface and narrow size distribution of about 90 nm, which was also supported by DLS data. Size and morphology of the particles remains the same on redispersing the lyophilized powder of these nanoparticles in aqueous buffer. Further, these nanoparticles were loaded with different synthetic oligonucleotides (ODNs). In vitro pH dependent release of the adsorbed oligonucleotides from these nanoparticles was also studied. At basic pH the release of oligonucleotides was found higher as compared with neutral and acidic medium. Cytotoxicity studies done on HEK 293 cells reveals that oligonucleotide loaded nanoparticles have high cell viability of nearly 76,88% whereas those of lipofectamine was about 35%. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 [source] Electrosprayed polymer particles: Effect of the solvent propertiesJOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2009Chul Ho Park Abstract Electrospraying technology has been studied in many fields to produce particles of various substances from nanoscale to microscale sizes. Unlike pure liquids, droplets formed by electrospraying that are comprised of polymer solutions undergo additional solidification processes involving solvent evaporation, which primarily determine the particle size and morphology. Herein, the effects of the solvent properties on the morphology and dimensions of solidified particles were systematically studied. In general, the size of the solidified spherical particles with smooth surfaces reflected that of the initially formed liquid droplets, which could partially be estimated by theoretical equations developed for pure liquids. Particle sizes increased with an increase in polymer content and a decrease in the boiling point of the volatile solvent. Inhomogeneous drying processes related to phase separation or skin formation resulted in hollow, cuplike, and porous particle structures, with particle sizes and morphologies that were outside of the scope of the theoretical treatments. The selection of a proper solvent or solvent mixture seemed to be a convenient way to control the particle morphologies, such as hollow, cuplike, or porous structures. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009 [source] Polystyrene nanocomposite materials by in situ polymerization into montmorillonite,vinyl monomer interlayersJOURNAL OF APPLIED POLYMER SCIENCE, Issue 6 2007Ahmed Akelah Abstract A different series of new polystyrene,clay nanocomposites have been prepared by grafting polymerization of styrene with vinyl-montmorillonite (MMT) clay. The synthesis was achieved through two steps. The first step is the modification of clay with the vinyl monomers, such as N,N -dimethyl- n -octadecyl-4-vinylbenzyl-ammonium chloride, n -octadecyl-4-vinylbenzyl-ammonium chloride, triphenyl-4-vinylbenzyl-phosphonium chloride, and tri- n -butyl-4-vinylbenzyl-phosphonium chloride. The second step is the polymerization of styrene with different ratios of vinyl-MMT clay. The materials produced were characterized by different physical and chemical methods: (1) IR spectra, confirming the intercalation of the vinyl-cation within the clay interlayers; (2) thermogravimetric analysis (TGA), showing higher thermal stability for PS,nanocomposites than polystyrene (PS) and higher thermal stability of nanocomposites with of phosphonium moieties than nanocomposites with ammonium moieties; (3) swelling measurements in different organic solvents, showing that the swelling degree in hydrophobic solvents increases as the clay ratio decreases; (4) X-ray diffraction (XRD), illustrating that the nanocomposites were exfoliated at up to a 25 wt % of organoclay content; and (5) scanning electron microscopy (SEM), showing a complete dispersion of PS into clay galleries. Also, transmission electron microscopy (TEM) showed nanosize spherical particles of , 150,400 nm appearing in the images. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3739,3750, 2007 [source] Quantitative evaluation of the prosthetic head damage induced by microscopic third-body particles in total hip replacementJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 4 2001Manuela Teresa Raimondi Abstract The increase of the femoral head roughness in artificial hip joints is strongly influenced by the presence of abrasive particulate entrapped between the articulating surfaces. The aim of the present study is to evaluate the dependence of such damage on the geometry of the particles entrapped in the joint, with reference to the UHMWPE/chrome-cobalt coupling. Five chrome-cobalt femoral heads and their coupled UHMWPE acetabular cups, retrieved at revision surgery after a short period of in situ functioning, have been investigated for the occurrence of third-body damage. This was found on all the prosthetic heads, where the peak-to-valley height of the scratches, as derived from profilometry evaluations, ranged from 0.3,1.3 ,m. The observed damage has been divided into four classes, related to the particle motion while being embedded into the polymer. Two kinds of particle morphology have been studied, spherical and prismatic, with size ranging from 5,50 ,m. In order to provide an estimation of the damage induced by such particles, a finite element model of the third-body interaction was set up. The peak-to-valley height of the impression due to the particle indentation on the chrome-cobalt surface is assumed as an index of the induced damage. The calculated values range from 0.1,0.5 ,m for spherical particles of size ranging from 10,40 ,m. In the case of prismatic particles, the peak-to-valley height can reach 1.3 ,m and depends both on the size and width of the particle's free corner, indenting the chrome-cobalt. As an example, a sharp-edged particle of size 30 ,m can induce on the chrome-cobalt an impression with peak-to-valley height of 0.75 ,m, when embedded into the polyethylene with a free edge of 5 ,m facing the metallic surface. Negligible damage is induced, if a free edge of 7.5 ,m is indenting the counterface. Our findings offer new support to the hypothesis that microscopic third-body particles are capable of causing increased roughening of the femoral head and provide a quantitative evaluation of the phenomenon. © 2001 John Wiley & Sons, Inc. J Biomed Mater Res (Appl Biomater) 58: 436,448, 2001 [source] Flow of particles suspended in a sheared viscous fluid: Effects of finite inertia and inelastic collisionsAICHE JOURNAL, Issue 10 2010Micheline Abbas Abstract We investigate in this article the macroscopic behavior of sheared suspensions of spherical particles. The effects of the fluid inertia, the Brownian diffusion, and the gravity are neglected. We highlight the influence of the solid-phase inertia on the macroscopic behavior of the suspension, considering moderate to high Stokes numbers. Typically, this study is concerned with solid particles O (100 ,m) suspended in a gas with a concentration varying from 5% to 30%. A hard-sphere collision model (with elastic or inelasic rebounds) coupled with the particle Lagrangian tracking is used to simulate the suspension dynamics in an unbounded periodic domain. We first consider the behavior of the suspension with perfect elastic collisions. The suspension properties reveal a strong dependence on the particle inertia and concentration. Increasing the Stokes number from 1 to 10 induces an enhancement of the particle agitation by three orders of magnitude and an evolution of the probability density function of the fluctuating velocity from a highly peaked (close to the Dirac function) to a Maxwellian shape. This sharp transition in the velocity distribution function is related to the time scale which controls the overall dynamics of the suspension flow. The particle relaxation (resp. collision) time scale dominates the particulate phase behavior in the weakly (resp. highly) agitated suspensions. The numerical results are compared with the prediction of two statistical models based on the kinetic theory for granular flows adapted to moderately inertial regimes. The suspensions have a Newtonian behavior when they are highly agitated similarly to rapid granular flows. However, the stress tensors are highly anisotropic in weakly agitated suspensions as a difference of normal stresses arises. Finally, we discuss the effect of energy dissipation due to inelastic collisions on the statistical quantities. We also tested the influence of a simple modeling of local hydrodynamic interactions during the collision by using a restitution coefficient which depends on the local impact velocities. © 2010 American Institute of Chemical Engineers AIChE J, 2010 [source] Migration and sedimentation of spherical particles in a yield stress fluid flowing in a horizontal cylindrical pipeAICHE JOURNAL, Issue 10 2009Othmane Merkak Abstract This study looks at the dynamics of a particle suspended in a viscoplastic fluid, flowing in a horizontal circular cylindrical pipe. Inertia effects are negligible in comparison with viscous effects and plastic effects. The suspensions are highly stabilized and at rest the spheres cannot settle under gravity alone. The results of Merkak et al. (AIChE J. 2008;54:1129,1138) are extended, taking into consideration both particles of the same density or denser than the fluid and pipe-to-particle diameter ratios of 8 or 56. New migration phenomena in the sheared zone are thus evidenced when buoyancy forces are nil. In the case of particles denser than the fluid, it is shown how the spheres settle by bypassing the plug-flow zone. A map showing the stability of flowing suspensions could, thus, be drawn. © 2009 American Institute of Chemical Engineers AIChE J, 2009 [source] Capillary forces between two solid spheres linked by a concave liquid bridge: Regions of existence and forces mappingAICHE JOURNAL, Issue 5 2009David Megias-Alguacil Abstract This article focuses on the capillary interactions arising when two spherical particles are connected by a concave liquid bridge. This scenario is found in many situations where particles are partially wetted by a liquid, like liquid films stabilized with nanoparticles. We analyze different parameters governing the liquid bridge: interparticle separation, wetting angle and liquid volume. The results are compiled in a liquid volume-wetting angle diagram in which the regions of existence (stability) or inexistence (instability) of the bridge are outlined and the possible maximum and minimal particle distances for which the liquid bridge may be found. Calculations of the capillary forces discriminate those conditions for which such force is repulsive or attractive. The results are plotted in form of maps that allow an easy understanding of the stability of a liquid bridge and the conditions at which it may be produced for the two particle model. © 2009 American Institute of Chemical Engineers AIChE J, 2009 [source] | ||||||||||||||||||||||||||||||||||