			Home About us Contact

Shear-induced Migration (shear-induced + migration)

Distribution by Scientific Domains

Polymers and Materials Science	75%

Selected Abstracts

Shear-induced migration of nanoclay during morphology evolution of PBT/PS blend

JOURNAL OF APPLIED POLYMER SCIENCE, Issue 1 2008
Joung Sook Hong
Abstract In this study, we investigated clay migration and its localization in multiphase blend nanocomposite systems during the evolution of blend morphology to elucidate how a hydrodynamic stress and chemical affinity between the polymer and clay induce them. To observe the morphology evolution, a multilayered blend, alternatively superposed poly(butylenes terephthalate) (PBT) and polystyrene (PS)/clay films or PBT/clay and PS films, was subjected to homogeneous shear flow, 1 s,1. Furthermore, the morphology was observed at different shear rates 1 s,1. When the PBT/(PS/clay) multilayered blend is subjected to flow, the clay dispersed in the PS layer first migrates to the interface depending on the amount of applied strain. The clay at the interface causes the average drop size of blend morphology to become smaller and the blend morphology becomes more stable because of the coalescence suppression effect. As more shear is applied, the clay at the interface moves further into more compatible phase, PBT, although the viscosity of PBT is higher than PS. On the contrary, the clay in the PBT layer does not migrate to the PS phase at any shear rate, which means that its chemical affinity is strong enough to prevent shear-induced migration. The clay increases the viscosity of the PBT phase and results in a different morphology with a droplet, cocontinuous structure. As a result, when the clay is induced to migrate by hydrodynamic stress, it migrates into thermodynamically more stable positions at the interface or in the chemically more compatible phase, depending on the applied strain. Once it is located at a thermodynamically more stable position, it is difficult to push it out only by hydrodynamic stress. The location of clay is significantly affected by the morphology during evolution, which means that the blend morphology can control the droplet form and cocontinuous structure by control of the clay migration kinetics. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source]

Investigation of the relationships between die build up and die swell

POLYMER ENGINEERING & SCIENCE, Issue 2 2009
Todd A. Hogan
Die build up (DBU) is a common problem encountered during extrusion of polymers where material accumulates around the die exit and may cause defects in the surface of the product. This study was initiated to better understand the fundamental relationships between DBU and die swell. The study was conducted on a strand die extrusion system using an ethylene-octene polyolefin elastomer resin. This study demonstrated that die swell is not a root cause of DBU. It was shown that at constant shear rate, increasing the die L/D ratio results in an increase in DBU, while die swell decreases. The important variables influencing DBU for the resin used in this study were: the shear rate or shear stress in capillary portion of the die, the nominal residence time that the resin is exposed to the high shear stress in the die capillary, and the concentration of oligomers present in the resin or generated during processing. These data support the conclusion that DBU is due to the shear-induced migration of oligomeric species in the polymer to the die surface. Higher shear rates and stresses in the die promote this migration and result in a higher concentration of oligomeric species near the die wall. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers [source]

Role of erythrocyte deformability during capillary wetting

BIOTECHNOLOGY & BIOENGINEERING, Issue 2 2006
Ronghui Zhou
Abstract Deformability of erythrocyte was found to fundamentally alter the wetting dynamics of red blood cell (RBC) suspensions during their invasion into capillaries. Normal RBC suspensions failed to penetrate more than 1 cm into a glass capillary when the capillary radius was smaller than a critical value that is dependent on the erythrocyte concentration (about 50 µm for whole blood). In contrast, suspensions of rigidified RBCs, after cross-linking with different concentrations of glutaraldehyde or incubating with 100 ng/mL of an endotoxin, could penetrate any capillary larger than the erythrocyte dimension. The effect of RBC deformability on penetration was attributed to the enhanced shear-induced migration of normal deformable RBCs toward the capillary centreline, which imparted a higher average velocity to the RBCs than the average plasma velocity. As a result, the erythrocytes advanced into the capillary faster than the wetting meniscus, packing behind it to form a concentrated slug. This tightly packed slug had a high hydrodynamic resistance that could arrest the penetrating flow of concentrated suspensions into the small capillaries. © 2005 Wiley Periodicals, Inc. [source]