Home About us Contact
|
Home About us Contact | ||
|
|
||
Selective Membrane (selective + membrane)
Selected AbstractsOptimization of the Composition of Interfaces in Miniature Planar Chloride ElectrodesELECTROANALYSIS, Issue 15-16 2003Renata Paciorek Abstract Different solid contact arrangements for miniature screen-printed electrodes and silicon based electrodes for chloride ions were investigated. As an inner contact the electrochemically deposited gold on screen-printed silver and platinum (silicon based electrodes) were used. As the ion-exchanger for chloride methyl-tri- n -tetradecylammonium chloride with PVC or Tecoflex as the polymer matrix was used. The influence of different intermediate layers between inner contact and the ion selective membrane was studied. The best characteristic of the electrode was obtained for electrodes containing gold contact and conductive polymer (poly-3-octylthiophene) with adhesive admixture between the inner contact and the proper ion selective membrane. [source] Membrane reactor modelling, validation and simulation for the WGS reaction using metal doped silica membranesASIA-PACIFIC JOURNAL OF CHEMICAL ENGINEERING, Issue 1 2010S. Battersby Abstract In this work, a Matlab Simulink© model was developed to analyse and predict the performance of a metal doped silica membrane reactor for H2 production via both the high and low temperature water gas shift reaction. An activated transport model for mixed gas separation with combined reaction was developed to model the effects within a membrane reactor unit. The membrane reactor was modelled as a number of perfectly mixed compartments containing a catalyst bed and a gas selective membrane. The combined model provided a good fit to experimentally measured results for higher conversions up to equilibrium, which is generally the case for industrial applications. Simulation results showed that H2 separation and H2 recovery improved with pressure, due to the H2 concentration driving force across the membrane. For a single stage membrane reactor unit, a maximum conversion of 93% could be achieved with a H2 recovery rate of 95%. In addition, the membrane reactor efficiency increased at higher temperatures and lower H2O:CO feed ratios, allowing for CO conversion improvements by the membrane reactor. Copyright © 2009 Curtin University of Technology and John Wiley & Sons, Ltd. [source] Solar membrane natural gas steam-reforming process: evaluation of reactor performanceASIA-PACIFIC JOURNAL OF CHEMICAL ENGINEERING, Issue 1 2010M. De Falco Abstract In this work, the performance of an innovative plant for efficient hydrogen production using solar energy for the process heat duty requirements has been evaluated via a detailed 2D model. The steam-reforming reactor consists of a bundle of coaxial double tubes assembled in a shell. The annular section of each tube is the reaction zone in which Ni-based catalyst pellets are packed, whereas the inner tube is a dense Pd-based selective membrane that is able to remove hydrogen from the reaction zone. By coupling reaction and hydrogen separation, equilibrium constrains inside the reactor are circumvented and high methane conversions at relatively low temperatures are achieved. The heat needed for the steam-reforming reaction at this low operating temperature can be supplied by using a molten salt stream, heated up to 550 °C by a parabolic mirror solar plant, as heating fluid. The effects on membrane reactor performance of some operating conditions, as gas mixture residence time, reaction pressure and steam-to-carbon ratio, are assessed together with the enhancement of methane conversion with respect to the traditional process, evaluated in the range 40.5,130.9% at the same operating conditions. Moreover, owing to the use of a solar source for chemical process heat duty requirements, the greenhouse gases (GHG) reduction is estimated to be in the range 33,67%. Copyright © 2009 Curtin University of Technology and John Wiley & Sons, Ltd. [source] Steam reforming of propane in a zirconia membrane reactor with a Rh-supported Ce0.15Zr0.85O2 catalystASIA-PACIFIC JOURNAL OF CHEMICAL ENGINEERING, Issue 3 2009K. Kusakabe Abstract The steam reforming (SR) of propane for hydrogen production at 400,600 °C in a porous yttria-stabilized zirconia (YSZ) membrane reactor was investigated. The YSZ membrane was used as a hydrogen selective membrane. A Rh-supported Ce0.15Zr0.85O2 catalyst was packed in the membrane reactor because the catalyst was found to be the most suitable catalyst for the low-temperature SR of propane on the basis of the results obtained using a packed bed reactor. The conversion of propane in the membrane reactor was higher than that in a packed bed reactor due to the shift of equilibrium toward the hydrogen-producing side. In spite of relatively low permeation selectivity (ideal H2/CO selectivity = 9 at 100 °C), hydrogen permeation through the membrane caused an increase in the CO2 fraction and a decrease in the CO fraction in reformed gas. This indicates that the water-gas shift reaction was an important contributor in the product distribution in the membrane reactor. Meanwhile, the methane fraction remained largely unchanged, regardless of selective hydrogen permeation. Copyright © 2009 Curtin University of Technology and John Wiley & Sons, Ltd. [source] Membrane reformer PEM cogeneration systems for residential applications,Part A: full load and partial load simulationASIA-PACIFIC JOURNAL OF CHEMICAL ENGINEERING, Issue 3 2009Stefano Campanari Abstract This two-part paper investigates the performances and economic potential benefits of a fuel cell cogeneration system based on a membrane reformer (MREF), using polymer electrolyte membrane (PEM) fuel cells, applied to residential cogeneration. Part A of this work focuses on the thermodynamic analysis and simulation of the system at full and partial load conditions, discussing its performance by means of a sensitivity analysis carried out under different operating conditions. Part B presents the technoeconomic analysis of the proposed system integrated into a real residential application, dealing with the energy savings and the economic balances, and proposes a preliminary design of the cogeneration unit. The system is based upon a PEM fuel cell, integrated with a membrane reformer (MREF) to form a small-scale, highly efficient cogeneration unit, potentially suitable for application to distributed generation in the residential field. The high purity hydrogen fuel required by the PEM fuel cell is produced in the membrane reformer through hydrogen selective membranes based on a Pd-Ag alloy. The analysis is carried out aiming to define the system energy balances in all the conditions occurring under real operation, including the influence of ambient temperature and of the expected fuel cell efficiency decay with time. The discussion reveals the relevant potential advantages of the MREF solution with respect to fuel cell units based on steam reforming (SR) or auto-thermal reforming (ATR): when compared to these solutions, MREF exhibits a 10% points higher electrical efficiency and requires a much simpler plant layout. These results are the basis for the detailed system technoeconomic analysis carried out in Part B of the work. Copyright © 2009 Curtin University of Technology and John Wiley & Sons, Ltd. [source] | ||||||||||