Home About us Contact
|
Home About us Contact | ||
|
|
||
Pure Poly (pure + poly)
Selected AbstractsLower critical solution temperature determination of smart, thermosensitive N -isopropylacrylamide- alt -2-hydroxyethyl methacrylate copolymers: Kinetics and physical propertiesJOURNAL OF APPLIED POLYMER SCIENCE, Issue 5 2008Mohammad M. Fares Abstract The lower critical solution temperatures (LCSTs) were verified and determined for different molar feed ratios of N -isopropylacrylamide (NIPAAm) and 2-hydroxyethyl methacrylate (HEMA) monomers with ultraviolet spectroscopy and differential scanning calorimetry techniques. Increases in the NIPAAm monomer content played a crucial role in the LCST, which increased up to 36.7°C at 50 mol %. However, a further increase in the NIPAAm monomer content steadily reduced the LCST, which decreased to 33°C at 100 mol % NIPAAm [i.e., pure poly(N -isopropylacrylamide)]. The rate of copolymerization, assessed by the conventional conversion (%),time method, and the apparent activation energies were determined. The reactivity ratios of the monomers, determined by the Kelen,Tudos and Fineman,Ross techniques, together with the results of an equation, showed that the copolymer which formed was an alternating copolymer. The Q,e values for the NIPAAm monomer were determined. The equation showed the linear Arrhenius behavior of ln(r1r2) versus the reciprocal of the temperature (where r1 and r2 are the reactivity ratios of NIPAAm and HEMA, respectively): the activation energy difference [i.e., (E12 + E21) , (E11 + E22), where E12, E21, E11, and E22 are various activation energies] was found to be ,109 kJ/mol. The copolymers were characterized with 1H-NMR, 13C-NMR, Fourier transform infrared, ultraviolet,visible, thermogravimetric analysis, differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy techniques. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 [source] Preparation and characterization of infection-resistant antibiotics-releasing hydrogels rods of poly[hydroxyethyl methacrylate- co -(poly(ethylene glycol)-methacrylate]: Biomedical application in a novel rabbit penile prosthesis modelJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 1 2008M. Yakup Ar Abstract In this work, preparation and characterization of novel three different antibiotic loaded penile prosthesis in the rod form were investigated by copolymerization of 2-hydroxyethylmethacrylate (HEMA) with poly(ethylene glycol)-methacrylate, (PEG-MA). To achieve this goal, a series of novel copolymer hydrogels were prepared in rod form using HEMA and PEG-MA monomers via UV initiated photopolymerization. The thermal stability of the copolymer was found to be lowered by increase in the ratio of PEG-MA in the rod structure. Contact angle measurements on the surface of copolymer hydrogel demonstrated that the copolymer gave rise to a significant hydrophilic surface compared with pure poly(HEMA). The blood protein adsorption and platelet adhesion were significantly reduced on the surface of the copolymer hydrogels compared with control pure poly(HEMA). Poly(HEMA:PEG-MA;1:1)-1 formulation containing different antibiotics (20 mg antibiotic/g polymer) released about 90, 91, and 55% of the total loaded cephtriaxon, vancomycin, and gentamicin in 48 h at pH 7.4, respectively. Finally, antibiotics loaded biocompatible poly(HEMA:PEG-MA;1:1)-1 hydrogel compositions was used as a penile prosthesis in preventing cavernous tissue infections in a rabbit prosthesis model. The efficacy of the three different antibiotics loaded hydrogel system was evaluated in four different groups of rabbits, in which various infectious agents were inoculated. The animals were sacrificed after predetermined time periods, and clinical, histological and microbiological assessment on the implant side were carried out to detect infections. Eventually, we concluded that three different antibiotic loaded penile prostheses (i.e. poly(HEMA:PEG-MA;1:1)-1 hydrogel systems) were as effective as parenteral antibiotics applications. © 2007 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008 [source] A composite polymer/tricalcium phosphate membrane for guided bone regeneration in maxillofacial surgeryJOURNAL OF BIOMEDICAL MATERIALS RESEARCH, Issue 5 2001Anita A. Ignatius Abstract The aim of the study was the development of a resorbable membrane for guided bone regeneration (GBR) with improved biocompatibility, which should be stiff enough to avoid membrane collapse during bone healing. Combining a bioactive ceramic with a resorbable polymer may improve the biocompatibility and osteoconductivity of resorbable devices. The present article describes the preparation, the mechanical properties, and the in vitro degradation characteristic of a composite membrane made of poly(L, DL-lactide) and ,-tricalcium phosphate in comparison to a membrane made of pure poly(L, DL-lactide). The tensile strength and the elastic modulus as well as the molecular weight of the membranes were measured after in vitro degradation in buffer at 37 °C up to 28 weeks. The initial tensile strength of the composite and the polymer membrane was 37.3 ± 2.4 MPa and 27.7 ± 2.3 MPa and the elastic modulus 3106 ± 108 MPa and 3101 ± 104 MPa, respectively. The mechanical properties remained constant up to 8 weeks and then decreased slowly until week 28. The molecular weight of both membranes decreased steadily from 170,000 D to 30,000 D. It was concluded that the mechanical requirements for a membrane for GBR were fulfilled by the composite membrane. © 2001 John Wiley & Sons, Inc. J Biomed Mater Res (Appl Biomater) 58: 564,569, 2001 [source] Cationic photopolymerization of cis -2,3-tetramethylene-1,4,6-trioxaspiro[4,4]nonaneJOURNAL OF POLYMER SCIENCE (IN TWO SECTIONS), Issue 14 2009Ying-Gev Hsu Abstract The spiro-orthoester, cis -2,3-tetramethylene-1,4,6-trioxaspiro[4,4]nonane (cis -TTN) (I), underwent rapid cationic photopolymerization when exposed to UV light using diphenyliodonium salts as a photoinitiator. The polymer, poly[(trans -OCB)x, -(cis -OCB)x, -(CHO)y] thus formed consisted of poly(trans -2-oxycyclohexyl butanoate) (trans -OCB)x, (II), poly(cis -2-oxycyclohexyl butanoate) (cis -OCB)x, (III), and poly- (1,2-cyclohexene oxide) (CHO)y segments, and no expected pure poly(ether-ester), that is, poly(2-oxycyclohexyl butanoate), was isolated. The structure of the polymer was identified, and the mechanism of the reaction was deduced. The polymer thus formed exhibited expansion in volume during cationic photopolymerization when compared to that obtained by conventional cationic polymerization using a Lewis acid (e.g., BF3OEt2, CH3OSO2CF3, or SnCl4) as an initiator, which demonstrated volume shrinkage during polymerization. The volume expansion of the polymer during polymerization was due to (1) the lower content of the higher density (CHO)y segment in the polymer chain and, more importantly, (2) the higher and optimal mole ratio of (trans -OCB)x, and (cis -OCB)x, segments that led the polymer in a more disordered, less dense, and higher volumetric state. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3680,3690, 2009 [source] Synthesis and characterization of homo- and copolymers of 3-(2-cyano ethoxy)methyl- and 3-[methoxy(triethylenoxy)]methyl-3,-methyl-oxetanePOLYMER INTERNATIONAL, Issue 10 2005Lin Ye Abstract Two oxetane-derived monomers 3-(2-cyanoethoxy)methyl- and 3-(methoxy(triethylenoxy)) methyl-3,-methyloxetane were prepared from the reaction of 3-methyl-3,-hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo- and copolyethers were synthesized with BF3· Et2O/1,4-butanediol and trifluoromethane sulfonic acid as initiator through cationic ring-opening polymerization. The structure of the polymers was characterized by FTIR and1H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (Tg), the DSC data imply that the resulting copolymers have a lower Tg than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P-AN 20) is 1.07 × 10,5 S cm,1 at room temperature and 2.79 × 10,4 S cm,1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry [source] Facile High-Yield Synthesis of Polyaniline Nanosticks with Intrinsic Stability and Electrical ConductivityCHEMISTRY - A EUROPEAN JOURNAL, Issue 33 2008Xin-Gui Li Prof. Abstract Chemical oxidative polymerization at 15,°C was used for the simple and productive synthesis of polyaniline (PAN) nanosticks. The effect of polymerization media on the yield, size, stability, and electrical conductivity of the PAN nanosticks was studied by changing the concentration and nature of the acid medium and oxidant and by introducing organic solvent. Molecular and supramolecular structure, size, and size distribution of the PAN nanosticks were characterized by UV/Vis and IR spectroscopy, X-ray diffraction, laser particle-size analysis, and transmission electron microscopy. Introduction of organic solvent is advantageous for enhancing the yield of PAN nanosticks but disadvantageous for formation of PAN nanosticks with small size and high conductivity. The concentration and nature of the acid medium have a major influence on the polymerization yield and conductivity of the nanosized PAN. The average diameter and length of PAN nanosticks produced with 2,M HNO3 and 0.5,M H2SO4 as acid media are about 40 and 300,nm, respectively. The PAN nanosticks obtained in an optimal medium (i.e., 2,M HNO3) exhibit the highest conductivity of 2.23,S,cm,1 and the highest yield of 80.7,%. A mechanism of formation of nanosticks instead of nanoparticles is proposed. Nanocomposite films of the PAN nanosticks with poly(vinyl alcohol) show a low percolation threshold of 0.2,wt,%, at which the film retains almost the same transparency and strength as pure poly(vinyl alcohol) but 262,000 times the conductivity of pure poly(vinyl alcohol) film. The present synthesis of PAN nanosticks requires no external stabilizer and provides a facile and direct route for fabrication of PAN nanosticks with high yield, controllable size, intrinsic self-stability, strong redispersibility, high purity, and optimizable conductivity. [source] | ||||||||||